Band saw

BEKA-MAK BMSY-360DGH ECO

Condition: new, neu ca. 12 - 14 Wochen ab Auf Türkei 16700 € 320.64 € Schwenkrahmen 4800x34x1,1 mm 15 - 120 m/min 360 mm 360 mm 510x360 mm Godpfew Np N Eox Ah Hebg rund 360 mm, quadrat 360 rund 250 mm, quadrat 220 rund 280 mm, quadrat 260 860 mm 0.37 kW 3 kW 0.12 kW 2650 mm 1210 mm 1870 mm 1450 kg Hydraulic vice Inverter for contious variable band speed Continuously adjustable saw arm lowering speed Hydromechanical blade tension can be read via pressure gauge Control panel Chip brush Coolant equipment Operating instructions in German or English

Condition: used, turning diameter over bed 2400 mm turning diameter over slide rest 2200 mm turning length 10000 mm power capacity 185 kW faceplate diameter 1650 mm turning speeds 1,5 -150 U/min max. workpiece weight 70000 kg clamping diameter 1400 mm Technical data Working range Maximum turning diameter over support: 2200 mm Maximum swing diameter over bed: 2400 mm Maximum turning length: 10,000 mm Clamping diameter in the headstock faceplate: 300 - 1,600 mm with special jaws up to 2,050 mm Clamping diameter in the tailstock faceplate: 300 - 1,400 mm Maximum workpiece weight: 70000 kg Main drive, faceplate Faceplate diameter: 2000 mm Faceplate speeds, continuously adjustable in 4 stages: 1.5 - 150 rpm Maximum torque at rated speed: 220,000 Nm Drive power of main motor: 185 kW Flange centre point angle: 70° Supports Travel of the plunge slide: 500 mm Travel of the face slide: 1400 mm Quick adjustment, longitudinal: 2000 mm/min Quick adjustment, face: 800 mm/min Infinitely variable feed, longitudinal: 0.6 - 300 mm/min Infinitely variable feed, face: 0.3 - 120 mm/min Max. cutting force at support: 20,000 kg Tailstock Faceplate diameter (removable): 1650 mm Faceplate clamping diameter: 1400 mm Flange centre point angle: 70° Quick adjustment: 1250 mm/min Special equipment Copying device for first support Copying length 8500 mm Max. copying depth in one pass 500 mm Boring device: Boring bar 460 x 390 mm Drilling diameter 600 - 1000 mm Maximum drilling depth in one pass 2700 mm At Ks of 200 kp/mm² - s max. = 1.5 mm/rev a = max. chip cross-section 30 mm² at a projection of 1000 mm Reduced chip cross-section with increasing drilling depth A guide ruler for cone turning, adjustment angle up to 8° and a maximum cone length (in one pass) of 2000 mm, adjustment accuracy ± 5 minutes. A guide ruler for cone turning, adjustment angle up to 15° and a maximum cone length (in one pass) of 1000 mm, adjustment accuracy ± 5 minutes. Godpfx Aoxddvnsh Hjbg 125 kg auxiliary crane on spindle box.

Condition: new, Year of construction: 2025, 360 mm 4800 mm Gbedswp Tp Ropfx Ah Hjg 510 mm 360 mm 510x360 mm dimensions of saw-band 4800x34x1,1 mm

Condition: new, Comparable to Behringer, Kaltenbach, Kasto, Jaespa, etc. Patented miter system Continuously adjustable cutting speed Hydraulic feed control Hydraulic lifting and lowering of the saw frame Hydraulic material clamping Powerful frequency-controlled saw drive Swivel range 30° right / 45° left Cutting range in mm: Gbsdeh S Nxpspfx Ah Heg 45° left round 300, flat 300 x 300 90° round 410, flat 620 x 410 45° right round 360, flat 420 x 360 30° right round 300, flat 300 x 300 Remnant piece length without bundle clamping: 60mm Recommended options: Micro-spray device Laser light Clamping pressure regulator Powered chip brush Manual support roller Set-up elements

Condition: ready for operation (used), Year of construction: 2001, CNC milling machine TOS TV-1000 A CONTUR Manufacturer: Trens Model: MC 100 VA Year of construction: 2001 Condition: used Control unit: Heidenhain TNC 426 X-axis travel: 1000mm Y-axis travel: 600mm Z-axis travel: 760mm Gbsdpfehlp Iwjx Ah Hsg Table length: 1080mm Table width: 580mm Tool changer with 40 positions Tool holder according to ISO 40 Spindle speed: 8000 rpm Overall dimensions: L 3200 x W 2100 x H 2900 mm Weight: 6200 kg Shipping possible throughout Germany and Austria. Surcharge 1000 € Sale excluding warranty.

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements Gbsdpfofg E Hpox Ah Hjg all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: like new (used), Year of construction: 1987, functionality: fully functional, machine/vehicle number: 61373, IT IS IN WORKING CONDITION Gsdpfx Aevwlf Ieh Hsbg

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 450x320 saw band length 4250x34x1,1 mm Gbedpjfgyicsfx Ah Heg band speed 40 + 80 m/min table height 845 mm saw band width 34 mm total power requirement 2,2 kW weight of the machine ca. 0,985 t dimensions of the machine ca. 1,4 x 2,0 x 2,2 m Double miter band saw, hydraulic semi-automatic, DGS 350/450 HA-I · miter left + right 60° without machine conversion · 34 mm saw blade width · Large material support turntable, ball bearings · To position the saw blade guides using a very wide linear guide · Strong, robust transmission · Large chipboards · Infeed and outfeed roller Removable chip tray (disinfection) · Free-standing control panel, safe and ergonomic · Storage space for tapes, consumables · Cutting pressure regulator Feed regulator · Fully hydraulic vise Preload super fast (front loading) · Material height sensor (automatic cut start detection) Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise Optimum, material-independent cutting result through fine adjustment of the saw frame by means of: *Pressure Control Valve (Cutting Pressure Force) *Feed Control Valve (Speed) *Switch with pictogram, easy and clear to use

Condition: good (used), Spectro CIROS CCD Water Analyser - height: 105cm - width: 150cm - depth: 75cm Gbjdpefiqn Uofx Ah Hsg Good condition fully functional can be inspected and tested on site. Shipping also abroad. Inspection : Basically I would like to point out that in order to avoid misunderstandings, the article can be inspected and tested under power before purchase. Please ask questions before purchase to avoid any ambiguity. If you have general questions or would like to make an appointment for a viewing, I can be reached at any time at the telephone number below. Errors in the description and prior sale reserved. The value added tax is shown separately on my invoices. Dispatch with forwarding agent.

Condition: used, Year of construction: 2018, DEMAG Overhead Crane – 16 Tons Capacity – Year 2018 Manufacturer DEMAG Cranes & Components GmbH – Germany Type Industrial motorized overhead travelling crane – single or double girder Industrial Applications Heavy-duty lifting in steel plants, fabrication workshops, boiler-making, general machining, and logistics warehouses Main Technical Specifications: - Rated capacity: 16 tons (16,000 kg) - Year of manufacture: 2018 - Manufacturer: DEMAG – global leader in industrial lifting Gbjdpfx Aexb D Nvsh Hsg - Motorized travel on rails - Electric wire rope hoist (DEMAG standard, high capacity) - Power supply: industrial three-phase - Control: pendant or radio remote (depending on configuration) - Condition: used – recent, robust design 🧩 Machine Usage The DEMAG 16T overhead crane is engineered for heavy-duty lifting in demanding environments. Its high capacity and modern design ensure efficiency, safety, and long-term performance. ⚙️ Features / Differentiators - Medium-high capacity (16T) for heavy industrial operations - Recent build (2018) compliant with modern safety standards - Integrated DEMAG hoisting and electrical systems - Compatible with automation and remote-control options