Channel baler, baling press

BOA Continu 25 LB

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Iodpfeu Thbxox Ab Ija Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), total height: 3,020 mm, total length: 3,300 mm, total width: 5,100 mm, throat depth: 1,060 mm, zware dubbelkoloms lintzaag voor het zagen van hooggelegeerde staalsoorten automatische invoer van het werkstuk met automatische herpositionering CNC-gestuurde variabele snelheid voor invoer en zagen spaantransportband uitgerust met volledig gemotoriseerde Weisshaupt-rollenbanen: - 10,3 meter invoerrollenbaan (buiten) met 2 hydraulische klemmen voor de contouren van het werkstuk - 9 meter invoerrollenbaan (binnen) met 2 hydraulische klemmen voor de uitlijnen van het werkstuk - Maximale werkstukbreedte: 900 mm - elke rol is gemotoriseerd - de capaciteit van één rollenbaan is 4 ton - 4 meter uitvoerrollenbaan: Iodov Sfp Aopfx Ab Ioa één rollenbaan is uitgerust met een weegschaal om het werkstuk na het snijden te wegen (Sartorius-systeem) Max height of workpiece: 860 mm Sawspeed: 16 > 80 m/min Length of band saw: 10260 x 80 x 1,60 mm Power needed: 32 kW (100 amp) Weight: 9 ton (only machine)

Condition: excellent (used), fuel type: diesel, color: yellow, Year of construction: 1998, operating hours: 7,305 h, Year of manufacture: 1998 Number of cylinders: 4 Empty weight: 9.700 kg CE mark: yes Technical condition: very good Visual appearance: very good Price: On request Ijdpfxoxyiv Ee Ab Iea Please contact Ernst van Hek for more information

Condition: used, !! Short delivery time, we will be happy to advise you!! Iedpfx Aju T N Umob Isa A simple flow-wrapping machine that is suitable for packaging various products. Used.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. Iedpou Thhrsfx Ab Isa The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), grinding length: 3,500 mm, center width: 5,000 mm, Cylindrical Grinding Machine Manufactured by Joh. Schehr, Meuselwitz Type SAXW 1000 Weight 33 tons Center distance 5000 mm Grinding length 3.5 meters Concave and convex grinding direction Total length 9.6 meters Width 3 meters Height 2.4 meters 380 volts Iedpswb Dq Nefx Ab Ija The machine can be inspected under power at the supplier's factory.

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, Year of production: 2005 Manufacturer: GUK-Falzmaschinen Griesser & Kunzmann GmbH & Co. KG Machine availability – on request; Machine in use; possibility to carry out work tests during inspections; Good technical condition; Iedpfxorx S Iws Ab Iea Folding machine manufactured by the renowned German company GUK equipped with a high pile feeder (sheet picking with a suction roller from above) FL2-50, 2 folding pockets aggregates, pocket with maximum working widths of 50 cm and mobile chute delivery. Folding machine GUK model FA 50/6-6 FL2-50 – infeed width 500 mm (6+6 folding pockets). Maximum input format: 500 x 850 mm Minimum input format: 105 x 145 mm Minimum folding length: 45 mm Feed rate of sheets from feeder: 40 - 180 m/min Maximum performance: 27.000/from sheet A4 Power supply: 400 V/50 Hz Machine equipment: High pile feeder FL2-50; Batch counter. Multifunction counter programming the operation of the machine. Ability to fold sheets in groups (lots) of the given number in each lot, with stepless adjustment of the spacing between parties. I. folding unit FA 50/6, 6 folding pockets; Sound reduction hood, top. II. folding unit FA 50/6, 6 folding pockets Sound reduction hood, top. Mobile chute delivery S 520. To be added after I or II folding station.

Year of construction: 1963, condition: used, functionality: limited functionality, machine/vehicle number: 512804, 1963 Bobst SP900E with double action stripper in reasonable/good condition. Well-maintained.. in recent years for example sprocket wheels, main gripper chains, counterplate under cuttingplate, cardan joints to the feeding head, have been renewed (original Bobst parts) Ijdpfstyqizjx Ab Ioa Gripperbars have not been renewed recently, they are still in quite a good condition. The knee joints have almost no signs of wear. they were probably at some point and the machine has not been used much since then. There is hardly any screech on them. Machine is dismantled in our storage in the South of The Netherlands, dismantled and not under power. For seriously interested potential buyers we will further upgrade the machine and assemble it and give the possibility to test it inevery way they want. In that case price will be 22,000 euros, loaded on to your transport, EX SITE

Condition: good (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 75,07,50,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Isdpfxsic Rl Ds Ab Isa Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8t The hydraulic unit is functional, the drive motor is in the removed state.

Year of construction: 2007, condition: excellent (used), machine/vehicle number: 33-010, 16 station Gathering machine, handfeeding station, Criss-cross delivery, Spiral raceway, Main milling station, Spine preparation unit, Spine and side glue unit, Cover feeder, Single nipping station, Laydown delivery unit onto conveyor system. Iodpfx Abjh T Dhqe Ioa