Condition: ready for operation (used), Year of construction: 2012, pressing force: 40 t, Manufacturer: HSM Dlsdpfx Aex D U N Sjddea Model: HL 4010 Year of manufacture: 2012

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 1800x1800x1900 mm Weight 3000 kg Dljdpfxjvz Ex Nj Addja Total power requirement 33,5 kw

Condition: new, Year of construction: 2025, Only one machine still available for immediate delivery! Delivery in December 2025 still possible. Briquetting press with PLC control and automatic briquette length adjustment Throughput: up to max. 60 kg/h Briquette: 50 mm cylindrical Motor: 5.5 kW Dimensions: 1,900 x 1,350 x 1,410 mm Weight: approx. 860 kg Dlsdpsv Rpxlofx Addja Requirements: Feed material should ideally be shorter than 25 mm in chip length Moisture content 6–12% (absolutely dry basis) Machine suitable for intermittent operation. For example, up to 2.5 hours briquetting; 1 hour pause, etc. If the machine is to run continuously for longer than 2.5 hours at a stretch, optional cooling must be installed.

Condition: used, Year of construction: 2006, power: 5 kW (6.80 HP), FOR SALE/RENT The compactor is suitable for compacting secondary raw materials as well as foodstuffs or other wet waste. Year of manufacture: 2006 Volume: 18 m³ Container dimensions (L x W x H): 5800 x 2500 x 2550 mm Dljdpfx Asx Dlmbsddja Filling height without wheels: 1540 mm Pressing force: 370 kN Motor power: 5.5 kW

Condition: good (used), Year of construction: 2016, functionality: fully functional, Baler Avermann, Model AVOS 1410 BR5 – 45/80, Pressing Force 80 t, Year of Manufacture 2016 Technical Specifications: Manufacturer: Avermann Maschinenfabrik Model: AVOS 1410 BR5 – 45/80 Dedpfx Adjx Dkkxjdela Year of manufacture: 2016 Pressing force: 80 t Drive power: 45 kW Feed opening: 1,400 x 1,000 mm Throughput at 35 kg/m³: 6.0 t/h Throughput at 60 kg/m³: 10.5 t/h Throughput at 100 kg/m³: 17.5 t/h Bale dimensions: 1,100 x 750 mm (W x H), length variable Bale weight: up to 600 kg, depending on material Tying: 5-fold vertical, automatic Machine dimensions: approx. 10,850 x 2,400 x 3,800 mm (L x W x H) Machine weight: approx. 18,000 kg Remarks: The press is still in operation and can be inspected upon request. It is expected to be available from February 2026. A suitable WESTERIA conveyor belt is optionally available. The main cylinder was replaced in November 2025. Additional images available upon request. Please feel free to contact us. Please note: All technical data are based on manufacturer’s information. We do not accept liability for any errors or omissions in the provided specifications. This offer is non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are available by appointment. Sale is ex works, prepaid, without guarantee or warranty.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Dlsdpfx Adjx Dnb Uedsa Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), functionality: fully functional, Brand: HSM Model: VK 20/1200 Motor: 11 kW Dedpfxsxnzf Is Addela Final bale size: 700 x 800 mm Bale weight: 200–350 kg

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 1850x1500x1230 mm Dledpfovz Eqlex Addsa Weight 870 kg Total power requirement 8 kw

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 60 t, input voltage: 400 V, bale weight: 550 kg, overall weight: 2,450 kg, Used HSM V-Press 1160 Plus vertical press from 2016. The device is regularly serviced by an authorized service center. The press is fully functional and in very good technical and technical condition. Crushing force: 594 kN Voltage / required: 400 V / 50 Hz Width x height of the loading opening: 1195 x 650 mm Bale length x width x height: 1200 x 1100 x 1200 mm Width x height x height of the machine: 1780 x 1568 x 2985 mm Dlodpfsx Eb Aujx Addoa Machine weight: 2403 kg Pressed material: foil, mixed paper, cardboard, cutting machine waste Freight costs depend on the weight, volume and above all on the distance, the following information is relevant for inquiries: Delivery address (postcode and name of the town), but further details require a telephone call, so we ask you to inquire about transport costs and other delivery modalities to contact us by phone. Our contact details can be found under the legal information of the seller. We sell and export worldwide, due to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-community invoices - excluding VAT. Opening hours Mon-Fri: 8 a.m.-4 p.m. sat .: closed

Condition: used, Year of construction: 2006, WE ARE SELLING OR RENTING A PRESS STATION WITH A SCREW SYSTEM AND 1 UNIT CAPACITY, SUITABLE FOR PRESSING SECONDARY RAW MATERIALS! MANUFACTURER - PRESTO GmbH (Germany) Dodox Dllwjpfx Addela Model: SPN15 Year of manufacture - 2006 CAPACITY - 30 m³ Power - 11 kW We offer rental of this unit in Lithuania, Latvia, Estonia, and Poland! PRICE UPON REQUEST!

Condition: good (used), Year of construction: 2002, functionality: fully functional, Vertical baler HSM VL 600, year of manufacture 2002 Technical data: Manufacturer: HSM Model: HSM VL 600 Year of manufacture: 2002 Pressing force: 60 t Drive power: 7.5 kW Cycle time (idle): 37 s Filling height: 1130 mm Filling opening: 1150 x 735 mm Dsdpfjx A Ur Djx Addsla Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Machine weight: 3575 kg Materials: Paper, cardboard, film Note: The operating manual is available. Please note: All technical data is based on manufacturer specifications. We do not accept liability for the accuracy of the information provided or for any possible errors. Offers are subject to change, prior sale reserved, and may be withdrawn at any time. Inspections are possible by appointment. Sale ex location, without warranty or guarantee. Our payment terms are 100% advance payment.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame Dlodpfx Ajx A U Nceddja • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: excellent (used), pressing force: 25 t, Equipment: documentation/manual, Tested, cleaned, full service performed. Fully equipped, ready to use! Dledpfx Asx Alcteddsa

Condition: excellent (used), Year of construction: 2017, pressing force: 48 t, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total width: 2,583 mm, total height: 3,994 mm, total length: 6,661 mm, Equipment: documentation/manual, HSM VK 4812 P Year of production: 2015 Fully automatic baler. The device has service and maintenance work by an authorized HSM service with a branch in Germany. The baler comes complete with a ramp for ejection of finished bales and stands for binding wires. Dledpfxex Ebzks Addsa Pressing force: 480 kN Drive power: 18 kW Voltage / frequency: 400 V / 50 Hz Capacity at 50 kg/m³: 10.2 t/h Bale width x height x length: 1100 x 750 x 600 - 1200 mm Total length x width x height: 6661 x 3994 x 2583 Machine weight: 10.2 t Compressed material: foil, mixed paper, cardboard, die-cutter waste Bale tying: 4-fold with wire We also have other presses in stock. Transport costs depend on weight, volume and, above all, distance, the following information is important for inquiries: Delivery address (postal code and city name), but further details require telephone contact, so please inquire about transport costs and other delivery methods to contact us contact us by phone. Our contact details can be found in the seller's legal information. We sell and export worldwide, and thanks to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-Community invoices - without VAT. opening hours Mon-Fri: 8:00-16:00 Sat: closed

Condition: used, Year of construction: 2020, Lifter system for containers for sale/rent – unused!\nType – HKV\nManufacturer – Ludden & Mennekes\nYear of manufacture – 2020\nFits 4-wheel MGB with flat lid, as well as 2-wheel 240 ltr MGB. Dsdox Dlldepfx Addela

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, pressing force: 5 t, Equipment: documentation/manual, Fully equipped, ready to use! Works perfectly. Djdpjx Alb Nsfx Addela

Condition: used, Year of construction: 1991, power: 3 kW (4.08 HP), For sale or rent! We are offering an HSM 155VL vertical baler. Manufacturer: HSM Model: 155VL Year of manufacture: 1991 Motor power: 3.5 kW Dljdpfjx Dldgsx Addja

Condition: used, Year of construction: 1992, pressing force: 30 t, power: 15 kW (20.39 HP), AFFORDABLE BALER FOR SALE WITH DEFECT! Technical Specifications: Manufacturer: Homa Model: BP3000P Year of Manufacture: 1992 Filling Opening: 1050 x 820 mm (L x W) Drive Power: 15 kW Dljdex Dlc Aspfx Addoa Pressing Force: 30 t Settings: Horizontal, fully automatic Bale Size: 800 x 900 mm Bale Weight: ~300 kg Machine Weight: approx. 5,650 kg Defect – Oil has leaked from the system; water may have entered the system! PRICE: EUR 5,500 (EXW Lithuania, Vilnius)

Condition: used, Year of construction: 2007, power: 7 kW (9.52 HP), FOR SALE OR RENT: VERTICAL BALER! (Rental available in Lithuania, Latvia, Estonia, and Poland) Technical Specifications: Manufacturer: HSM Model: HSM 500 VL Djdpfsx Dlb Ejx Addjla Pressing Force: 54–540 kN Bale Size: 1200 x 800 x 1200 mm Bale Weight: approx. 500 kg Max. Bale Size: approx. 1200 x 800 x 1200 mm (W x D x H) Press Chamber Dimensions: 1200 x 800 x 1520 mm (W x D x H) Motor: 7.5 kW Year of Manufacture: 2005 PRICE ON REQUEST!

Condition: used, Year of construction: 2002, pressing force: 115 t, power: 150 kW (203.94 HP), For sale: Paal Konti 425 D horizontal baler Technical specifications: Manufacturer: Paal Model: Konti 425D Year of manufacture: 2002 Feed opening: 102 x 200 cm Dledpjx Dlansfx Addea Drive power: 2 x 45, 2 x 75 kW Pressing force: 115 t Settings: horizontal, fully automatic Bale weight: 550-850 kg Pressing weight: 36 t PRICE ON REQUEST!

Condition: used, Year of construction: 1995, pressing force: 85 t, power: 170 kW (231.14 HP), BALER PAAL KONTI 425 C Technical specifications: Manufacturer: Paal Model: Konti 425C Year of manufacture: 1995 Feed opening: 102 x 175 cm Drive power: 170 kW Compression force: 85 t Settings: Horizontal, fully automatic Bale weight: 500-650 kg Dedpfxsx Dk Tts Addela Press weight: 25 t PRICE ON REQUEST!

Condition: used, Year of construction: 2008, power: 3 kW (4.08 HP), The HSM V-Press 610 is a powerful baler designed for medium to large volumes of waste, making it ideal for commercial and industrial use. This model combines high capacity, efficiency, and reliability, allowing for the effective compaction of a wide range of waste materials. Pressing force: 120 kN Drive power: 3 kW Filling height: 655 mm Filling opening (width x height): 800 x 495 mm Bale length x bale width x bale height: 800 x 600 x 600 mm Bale weight: 100 kg Dimensions (W x D x H): 1198 x 823 x 1986 mm Dledpex Dk Tgjfx Addea Weight: 540 kg Related product line: V-Press Consumables: Strapping Compression materials: Plastic film, mixed paper, cardboard, punching waste! PRICE ON REQUEST!

Condition: used, Year of construction: 1994, pressing force: 40 t, power: 22 kW (29.91 HP), Horizontal Baler for SALE/RENT BAUER 300 The baler is in good working condition (previously used in a print shop)! Technical specifications: Installation of secondary raw material baler Manufacturer: BAUER Dsdpfxex Dk S As Addsla Model: 300 Year of production: 1994 Power: 22 kW Pressing force: 40-50 t Dimensions of the baler: 10,300 x 2,000 x 3,000 mm Tipping weight: approx. 400 kg PRICE ON REQUEST!

Condition: new, Year of construction: 2021, power: 11 kW (14.96 HP), NEW SCREW PRESS STATION WITH 2 PC6500 BOXES FOR SALE! Dljdjx Dk Scspfx Addoa Technical specifications: Total length: 2480 mm Total width: 1660 mm Total weight: 2300 kg Loading height: 1350 mm Inlet dimensions: 1375 x 1490 mm Screw diameter: 750/500 mm Screw speed: 17 rpm Drive power: 11 kW Year of manufacture: 2021, never used! The press station is equipped with a screw system +KEV (carton feed/diversion, coarse shredding unit, corresponding to KZK, only more powerful) PRICE ON REQUEST!

Condition: used, Year of construction: 1994, pressing force: 30 t, power: 22 kW (29.91 HP), LIKON 200C Horizontal Baler Technical Data: Motor Power: 22 kW Year of Manufacture: 1994 Equipped with oil cooler Horizontal tying: 4 x Pressing force: 30 t Overall dimensions of the baler: 10,000 x 2,000 x 2,750 mm Net weight of the baler: 10 t Loading opening dimensions: 1,400 x 700 mm Bale dimensions: 700 x 1,100 x 1,000–1,200 mm (variable length) Dljdpfx Ajx Dk Iwoddoa Includes hydraulic oil No tying wire included Previously operated in a print shop without a conveyor, used exclusively for dry-shredded print waste! Operating hours: 62,639 The baler is in good condition and ready for use. PRICE ON REQUEST!