Cylindrical grinding machine

CETOS BUC 63 B/4000

Condition: used, Year of construction: 1997, Technical details: max. module: 7 weight of the machine ca.: 5 t worm grinding diameter: 280-350 mm width of grinding worm: 84-104 mm min. number of teeth: 6 max. number of teeth: 600 max. top circle diameter: 360 mm Gedpsx Aq Egofx Afqsiw max. workpiece weight: 60 kg without filter *

Year of construction: 1998, condition: good (used), Make: UNION Type: Ti 1800 Year: 1998 Specifications Metric US Standard Table Length 2000 mm Table Width 1800 mm Table load 16000 Movement V-axis 1250 mm Rotation B-Axis 360.000 ° Rotation speed B-Axis 1,35 Omw/min. Movement speed V-axis 4000 mm/min. Dimensions (Estimate) Length 3400 mm Width 2000 mm Height Gijdpfskwcdbjx Afqjw 920 mm Weight 6500 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, Gjdpfjfx Hv Hsx Afqsiw various accessories

Condition: used, Year of construction: 2000, Kellenberger 600 U cylindrical grinding machine Condition: Used Year of manufacture: 2000 Technical data: Table: Distance between centers: 600 mm Travel: 900 mm Gisdoy T E Rzepfx Afqow Travel per handwheel revolution, coarse/fine: 20 / 2.5 mm Travel per division on the handwheel: 0.05 mm Speed, hydraulically continuously variable: 0.02 - 6 m/min Reversal travel, minimum: 2.5 mm Dwell time during reversal, continuously variable: 0 - 5 sec Swiveling range: 11 degrees Cross slide: Travel with feed handwheel in fine or coarse mode: 220 mm Travel per handwheel revolution, coarse/fine: 8 / 1 mm/ø Division on the handwheel: 5 µm/ø Division with micrometer adjustment: 1 µm/ø Rapid traverse, hydraulically: 40 mm Feed, hydraulically: 0.95 mm/ø Form grinding: Feed rate: 0.25 - 25 µm/sec Surface grinding: Feed increments per table reversal: 130 µm/ø Grinding spindle head: Grinding wheel for external cylindrical grinding: 400 x 50 x 127 mm

Condition: ready for operation (used), Year of construction: 1969, Centre height: 355 mm Centre distance: 3000 mm Max. swing diameter over bed/gap/cross slide: 715/790/520 mm Spindle bore: 86 mm Spindle mount according to DIN 55027: Size 11 Quill taper of tailstock: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/cross: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitworth threads: 2 - 28 TPI 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module Gijdpfx Afjxpuu Eoqjw 32 diametral pitch threads: 8 - 112 DP Drive motor, pole-changeable: 380 V, 7/11 kW Weight approx.: 7 t Space requirement approx.: 6000 x 2300 mm

Condition: used, Radial drilling machine CSEPEL, Type RFh 75 / 1500 Machine no. 13704, Year of manufacture 1985 Drilling capacity in steel: Ø 75 mm Drilling capacity in cast iron: Ø 90 mm Spindle mount: MK 5 Nominal overhang: 1500 mm Maximum overhang of the spindle: 1500 mm (to the column) Gijdpfx Afslhwr Reqow Minimum overhang of the spindle: 440 mm (to the column) Distance from spindle nose to clamping surface: 370 - 1700 mm Overarm vertical adjustment: 950 mm Table size / clamping surface: 1800 x 1100 mm Column diameter: 450 mm Quill stroke: 380 mm Spindle speed: 19-1900 rpm, 21 steps Feed rate: 0.047-2 mm/rev, 12 steps Motor power: 11 kW Mains connection: 380 Volts, 50 Hz, 15 kW - Right-hand and left-hand rotation of the drilling spindle via hand lever switch - Hydraulic gear change for spindle speed and feed rate - Hydro-mechanical central clamping device - Motorized overarm vertical adjustment - Without coolant system - Machine light - Operating manual Space required: Length 2720 mm x Width 1170 mm x Height max. 3770 mm Transport height with motor on the column: 3500 mm Transport height without motor on the column: 3250 mm Weight: 6.3 tons Good condition

Condition: good (used), Make: Ursviken Type: VPF 1000/800-5,0 Control: Siemens Simatic panel Gisdpskvmi Sofx Afqjw Year: 1970 Hydraulic press for fabrication off large componts like dish heads tanks boiler shipyard and steelconstruction Renewed in 2015 with Siemens SIMATIC panel and E-Cabinet Rittal Build in height 2950 mm Maximum die height 1500 mm Movable Table & Piston in X-Ways Large package Die tooling radius 10/20/30/50/60/80/100 Pressing force 210 kg/cm2 Maximum stroke 800 mm Machine 2350 mm placed in ground Specifications Metric US Standard Capacity Kg 1000 Ton Distance between column 5010 mm Table Length 3000 mm Table Width 2000 mm Table Height 550 mm Ram stroke 1450 mm Approche speed 50 mm/min. Working speed 5 mm/min. Return speed 50 mm/min. Dimensions (Estimate) Length 0 mm Width 0 mm Height 0 mm Weight 0 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1980, condition: good (used), A used, very well-maintained cycle-controlled lathe from Weisser Heilbronn with a SIEMENS control system. Distance between centers 2000 mm Center height 295 mm Swinging diameter over bed 600 mm Swinging diameter over cross slide 260 mm Swinging diameter in the crotch 800 mm Total length of the crotch 375 mm Bed width 450 mm Travel of X-axis 350 mm Travel of Z-axis 1850 mm Spindle nose DIN 55022, size 8 Spindle speed, number 18, 14 – 1400 rpm Spindle bore 71.5 mm Diameter of front bearing 110 mm Feed range 0.01 – 40.95 mm/rev Rapid traverse 8 m/min DC drive 15 kW 400V 50Hz Max. permissible torque on the spindle 2500 Nm Tailstock quill 80 mm Quill stroke 250 mm Internal taper in quill MK 5 Gisdpogyy I Aofx Afqjw Length x width x height Machine weight 5500 kg Accessories: Tailstock Pneumatic three-jaw chuck with replaceable jaws, 315 mm Quick-change tool holder "MULTIFIX" in front of the center, size "C" Four-position turret behind the center Tool holder Coolant system Follow rest, pneumatically actuated Technical data and dimensions: Subject to change without notice. Video conference via WhatsApp possible after scheduling an appointment.

Condition: reconditioned (used), machine/vehicle number: 550-235-ELD, GENERAL CHARACTERISTICS workpiece Ø max. 41 mm Range Module máx/min. 1,5 / 0.39 Rack face width 92 mm Manufacturing No. 550-235-ELD Máx/min. pitch form 20/40-32/64 Maximum stroke of tools trolley 760 mm Gijdpfed Nw Ttex Afqow Rack length máx. 610 mm ELECTRICAL CHARACTERISTICS Main motor power 15 Cv

Condition: used, table length 400 mm table width 300 mm x-travel 300 mm Gjdpfx Afovwgq Sjqeiw y-travel 250 mm z-travel 250 mm weight of the machine ca. 1,2 t dimensions of the machine ca. 2000 x 1200 x 2500 mm The machine is supplied with a wide range of accessories