Pallet strapping and film wrapping line

Cyklob XZE-3111- GL 2020 pallet conveyin

Year of construction: 2004, condition: good (used), Build in 2004 Description/configuration: Complete line for automatic pallet strapping, automatic stretch-wrapping of pallets. Includes fully automated pallet conveying. Line with ""straight""-configuration, built with chain conveyors and configured as follows: > Straight chain conveyor, motorized, travel is long side leading, l~1100 mm, REF 25778.01 > pallet strapper Cyklop XZE-3111, REF 25778.30 > Straight chain conveyor, motorized, travel is long side leading, l~1100 mm, REF 25778.02 > Straight chain conveyor underneath wrapper, motorized, travel is long side leading, l~2600 mm, REF 25778.03 > ring style pallet film wrapper Cyklop GL 2000, REF 25778.40 > Straight chain conveyor, motorized, travel is long side leading, l~1100 mm, REF 25778.04 > Straight chain conveyor, motorized, travel is long side leading, l~1100 mm, REF 25778.04" Layout available max speed in pallets/h: 50 pallets/h Chain conveyor Pallet width of up to 800 mm Pallet length of up to 1200 mm max height full pallet (max passage height): ~1700 mm Height of pallet conveying (min=300mm): ~400 mm max weight full pallet: ~1500 kg Nljdehrmlkjpfx Aqvob Over all length equipment: ~8000 mm Over all width equipment: ~6000 mm Over all height equipment: ~3500 mm Input Power: ~15 kw (whole line) Voltage: 400 V, 3 Ph, 50 Hz Air requirement: 6 bar Equipment at central warehouse Helmstedt with nearest airports: Hannover (~1,5 hrs), Leipzig (~2hrs), Berlin (~2,5 hrs) Condition: cleaned & in working conditions Machine available: upon request

Year of construction: 2025, condition: new, Automated pallet dispenser is the backbone of your automation processes. Loaded with up to 10 euro pallets (1200x800 or 1200x1200), it removes the need to prepare each pallet manually, saving time and reducing strain on employees. Instead, the unit dispenses pallets with a push of a button, or a pre-set algorithm onto a motorised roller conveyor, which transports them for further processing. PD-10 can be used in line with various palletising solutions. Nljdpjhbg Uxefx Aqvsb Fits up to 10 euro pallets Loaded up with a forklift Reduces physical strain Increases efficiency

Condition: excellent (used), Year of construction: 2016, Inca Onset X2, 3/4 automized Color configuration: 8 channel printer with four colours (CMYK) 1/12th of the new price !!!!! Printhead status allowing to print at maximum speed with outstanding quality, up to 140 beds per hour/700m² per hour, needs replacement of 60 heads (circa 45.000€) The machine is in excellent shape, serviced by manufacturer since day number one. Annual maintenance done in May 2025. Available: January 2026 Nlodpfeun Swbex Aqvsb As the business expands, Onset X2 provides the capacity to extend the range of jobs companies can handle. The addition of a second set of CMYK delivers even higher productivity - up to 707m²/hr* (equivalent to 138 full-bed sheets/hr) - while an optional six channels can be populated with light cyan (Lc), light magenta (Lm), white (W) and orange (O) to add versatility and superb quality. A choice of uni-directional, bi-directional and super high-quality print modes can be selected depending on the specific job requirements. * Based on an approximate 6 second material handling time. Decomissioning, transport, installation, training and warranty are included (in Europe) For further technical details please refer to enclosed data sheet.

Condition: used, Aufspannplatte - Tisch einer Langhobelmaschine - Tischbreite/Aufspannbreite: 1845 Tischlaenge/Aufspannlaenge: 5505 mm Nodpfxebn Amfo Aqvelb 7 T-Nuten laengs fuer T-Nutensteine: M 30 T-Nutenabstaende zueinander: 263 mm Gesamtlaenge: 6230 mm Plattenhoehe insgesamt: 350 mm Gewicht: 11 t

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h Nlsdovf E Avopfx Aqvjb bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: excellent (used), Year of construction: 1993, CNG Tank Gas Methane Trailer Natural gas 200 Bar Manufacturer: SAMRO Year: 1993 Tare: 6900 kg We also have other tanks for LIN, LOX, LAR, LNG and CO2, argon, oxygen, nitrogen and carbon dioxide, Hydrogen, Methane Nodpfst D Aptsx Aqvolb We would also be happy to provide you with a quotation or give you more information about other pressure vessels.To discuss the possibilities, please contact us by phone or e-mail.

Condition: new, Year of construction: 2026, functionality: fully functional, Ticab Printing System TPS is an innovative cantilever equipment. It allows feeding huge items beneath the print head. The print head can be adjusted up to 30 cm above the conveyor belt to feed folded cardboard boxes or other huge items. High quality Hewlett Packard HP pigment ink provides resistance to the fading, scratches and water after the image dries. Call us to get a beneficial commercial offer. Specifications: Nlsdpfx Aqju Ibhwjvob  Print area width: up to 29.7cm (11.7 in)  Print area length: from 2.54 cm (1 inch) to 91.44 cm (36 inch)  Workpiece movement speed: up to 45.72 cm (18 in) per second  Printing speed: up to 50--70 copies\min A4, up to 16 copies\min A3  Print resolution: 1200x1200dpi  Number of inkjet nozzles: 59136 (14 printing zones of 4224 nozzles each)  Colors: CMYK (Cyan, Magenta, Yellow, Black)  Ink type: water-based pigment ink  Information connection: Ethernet 10/100/1000 Base-T network port  Operating system: Windows (recommended Windows10)  Hewlett Packard HP driver  Trusted by professionals in 55 countries worldwide!

Condition: like new (used), Year of construction: 2000, operating hours: 25,000 h, travel distance X-axis: 10,300 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,800 mm, feed rate X-axis: 10 m/min, feed rate Y-axis: 10 m/min, feed rate Z-axis: 10 m/min, position of the milling head: 2.5 x 2.5 °, spindle speed (max.): 3,000 rpm, spindle speed (min.): 60 rpm, table width: 3,300 mm, table length: 12,000 mm, mount diameter: 50 mm, total height: 48,750 mm, total width: 1,00,000 mm, total length: 2,12,000 mm, overall weight: 1,00,000 kg, Duplex milling are two machines located one opposite the other which can work seperately or as single machine, workpiece can be machined with 2 simultaneous spindles. Production increase of up to 50% in relation to conventional solutions, i.e. individual milling machines Improvements in part precision, by managing to do the machining of the part in one single setup, in most of the cases One sole operator can control the DUPLEX milling machines Reduced space and investment requirement comparing with two single machines Fast investment amortization due to the high productivity Duplex solution admits different configurations: single working area, pendulum working areas For machining excavator arms / boom like, CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo X-Axis: 10300mm Y-Axis: 2000mm Z-Axis: 1800mm Table Length: 12000mm Table Width: 3300mm Table load: 100000 Power on spindle: 22/30kW Spindle speeds: 60 - 3000Rpm Spindle Taper: 50ISO/Bt/Mk Feed rate X-Axis: 10000mm/min. Feed rate Y-Axis: 10000mm/min. Feed rate Z-Axis: 10000mm/min. Njdpfx Aqorx Rxtsvolb Millinghead auto-index:2.5 x 2.5° Working hours: 25000H Length: 21200mm Width: 10000mm Height: 4875mm Weight: 100000kg

Year of construction: 1998, condition: good (used), Built in 1998 Size max 305 x 420 mm Size trimmed: max 300 x 400 mm min 100 x 100 mm Book block thickness: max 80 mm min 2 mm Feeding height 80 mm Speed max 3.900 c/h Length 2.400 mm Width 3.060 mm Height 1.740 mm Weight 5.290 kg (approx.) Equipment • automatic infeed with integrated pre stacker • gripper loading • cut counter • automatical speed regulation • offcut blower • Equipment for sheet-fed • 1 set of clamping plates and holders • 1 set cutting table • 3 sets of cutting sticks • 2 set of knives • automatic lock of knife adjustment and pressing block • external knife changing device • copilot • automatic setting of • - infeed device • - bookblock pressure • - cutting table • - side knives • - side gauges • - height of the delivery clamp • central lubrication Nodpsfu H Sxsfx Aqvelb • delivery clamp

Year of construction: 1991, condition: ready for operation (used), Filling format: 70-150g, forming shoulder format: 120/ 140mm, with three forming sets and multi head scale. Nledpfshtvmasx Aqvsb