Overband magnet Magnetic plate Block mag

die magnetprofis PEM620x420x200

Year of construction: 2003, condition: reconditioned (used), Stock - No. 2651 1 used underwater pelletizing unit, partially overhauled in 2023 Throughput up to approx. 450 kg/h depending on the material, consisting of: Type BKG ( Nordson ) Start-up valve with hydraulic station Granulator type A300 including die-plate and cutter bar, drive 4.4 kW by-pass system Kodpjiyyf Iefx Aayedk TVE 1000 ED pellet-dryer drive 4 kW incl. Agglomerate catcher Tempered water system with Water box 200 liters, installed heating capacity 9 kW Water pump 2.2 kW with 15³/h heat exchanger Control unit - NEW Further UWP pelletizing units are available ex workshop in Wuppertal-Germany ( as Gala, BKG Nordson, Econ ) Available from the Wuppertal warehouse: complete compounding, pelletizing extrusion lines, with single-screw or twin-screw extruder.

Condition: excellent (used), total width: 4,000 mm, total height: 7,000 mm, clearance between the columns: 2,000 mm, shelf length: 900 mm, Equipment: double-sided, Consists of 3 double-sided uprights, height 6000 mm 9 shelves with arms 750 mm long Load capacity per cantilever arm: 900 kg Load capacity per level: 2700 kg Load capacity per upright front: 8100 kg Kdjdpfx Aajulufpeyek Distance between uprights: 2000 mm

Condition: good (used), Gardner 800l ribbon blender Kedpslcdz Hjfx Aaysdk 800l ribbon blender, single shaft, stainless internals, swing top lid, discharge chute, 3Ph

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C Kdedpfxswp Rqfs Aayjk • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: good (used), Industrial robots Manufacturer: Kuka Model: KR6, KR6-2, KR6arc Model: KR16L6, KR16L6-2, KR16, KR16-2, KR16-2 S, KR16-2 F All models equipped with KRC2ed05 controller Kuka KR6 KRC2ed05 Year of manufacture 2006 Kuka KR6-2 KRC2ed05 Year of manufacture 2011 Kuka KR6arc KRC2ed05 Year of manufacture 2006-2007 = several units in stock Kuka KR16L6 KRC2ed05 Year of manufacture 2009 Kuka KR16L6-2 KRC2ed05 Year of manufacture 2011 Kuka KR16 KRC2ed05 Year of manufacture 2007-2009 = several units in stock Kodetuc U Rspfx Aayedk Kuka KR16-2 KRC2ed05 Year of manufacture 2010-2012 = several units in stock Kuka KR16-2 Speed KRC2ed05 Year of manufacture 2012 = several units in stock Kuka KR16-2 Foundry KRC2ed05 Year of manufacture 2012

Condition: used, 3-axle truck trailer, low-loader trailer MÜLLER MITTELTAL Type AZP Curtain-sided low loader, low-loader trailer, low loader for machine transport First registration: 2001 Total mileage: approx. 350,000 km Gross vehicle weight: 24,000 kg Unladen weight: 5,500 kg Payload: 18,500 kg Platform height: 840 mm Loading height under tarpaulin frame: 3,200 mm Platform length: 7,450 mm Overall length: 9,150 mm Overall width: 2,550 mm Overall height: approx. 4,050 mm Axle load front: 8,000 kg Axle load middle: 8,000 kg Axle load rear: 8,000 kg Tyres: Michelin 215 / 75 R17.5 (135/133J XTE 2+ TL) - Rear wing doors at drop side height - Tarpaulin frame with EDSCHA roof system - Tarpaulin frame designed for easy removal (can also be used with the frame removed and the tarp pushed forward) - Spare wheel mounted on the front wall - Independent lifting and lowering of front and rear axles - Middle axle with lift function - Drawbar – extendable in multiple stages - Heavy-duty lashing rings on the outer frame and in the vehicle centre Ksdot N Antjpfx Aaysdk - ALU drive-on ramps, length 268 cm, width 410 mm, height 130 mm (surcharge EUR 2,000 net) The trailer was purchased new by us and is therefore first-hand. The trailer has been deregistered since 2025.

Year of construction: 2025, condition: new, functionality: fully functional, machine/vehicle number: ESS B2 - *M 0--.10*, Mobile starscreen on trolley Suitable for material: soil, compost, topsoil, wood chips, building rubble, bark mulch Weight: 2700 kg Grain size: 12 to 40 mm (according to material requirements) Power supply: 3 phases, 400V, current 32A, frequency 50Hz, total power 11,25kW throughput: 40 to 60 m³/h depending on material and grain size Delivery time after order approx. 14 weeks Kdedpjirnrpefx Aayek

Condition: ready for operation (used), Year of construction: 2021, This 3-axis Hurco VM 10i was manufactured in 2021, featuring advanced capabilities like MAX5 control with dual 19" LCD displays, Ethernet and USB interfaces, and a solid-state drive for enhanced performance. It includes high-pressure coolant systems through the spindle, integrated hydraulic tool clamping, and a chip auger for efficient chip management. Consider the opportunity to buy this Hurco VM 10i vertical machining centre. Contact us for more information about this machine. • Includes MAX5 control with detachable electronic handwheel • 2 × 19" LCD color displays (text + graphics) • Network interface • 2 software units for programming • Internal self-diagnostics • Windows platform • Integrated hydraulic tool clamping system • Cooling flood through spindle with ICS (20 bar) • High-pressure cooling flood system • Spindle cooler • Chip auger • Chip splash guard cabin • LED machine light in the work area • Indicator light for machine operating status • Trochoid milling cutter function for higher machining performance Kdodpfx Aaox H A I Reyek • Tool and workpiece measurement • Collision protection with islands • Synchronous thread cutting • ISNC extended NC mode

Condition: new, Klanke Supercut roll splitter for efficient shredding of reject rolls. Features: -Automatic safety lock Kdjden I Rgpepfx Aaysk -Emergency stop rip cord -Siemens SPS Technical data: Blade length: 3000mm Cutting channel opening: 1200mm Motor power: 15kW Cutting force: 50to Order goods Price and further information on request. We will be happy to make you a non-binding offer.

Condition: used, SINGLE SHAFT SHREDDER WEIMA MODEL WLK15 MAIN MOTOR 90KW ROTOR KNIVES SIZE 50X50 (NEW KNIVES) ROTOR LENGTH 1500MM ROTOR DIAMETER 370MM THE MACHINE IS 100% FUNCTIONAL Kdjdpfx Aajtqd Ndsyok READY TO WORK