EMME ELLE POLISHING MACHINE

EMME ELLE L.B.A. 1350

Condition: new, Year of construction: 2023, Standby power 20 kVA (16 kW) Full load 17.5kVA (14kW) Voltage 230/400V Kedpfx Adsi Nthqowsdg Generator power 16 kW Generator continuous power 14 kW Number of phases 3 ECU adjustment Fuel tank capacity 60 l Liquid cooling Frequency 50Hz Rotation speed 1500 rpm. Engine type in-line, 4-cylinder, naturally aspirated Cylinder diameter and length 98 x 105 mm Engine capacity 3.2 liters Capacity oil approx. 3 l (between the min./max. value on the dipstick) Capacity coolant approx. 5 l diesel fuel Compression ratio 17.2:1 DATAKOM D300 control panel Insulation class (alternator) H Number of windings (alternator) 12 IP degree of protection (alternator) IP23 Shunt excitation type Voltage (alternator) +/- 1% Overall dimensions (length x width x height) 2000 x 900 x 1070 mm EURO III emission standard Weight 730 kg

Condition: reconditioned (used), Totally renovated Log Haul Conveyor 8 Meters long Kedpfx Aencft Ujdwjdg

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, Fully working UniControl 12 year 2006 from Norway - for exact technical specification please open attached document in PDF below. Cross section UniTec 12: - saw unit - edge round cutter from bottom - Hubspindel no.1 - Hubspindel no.2 - Hubspindel no.3 Long , profile section UniVar 12: - Profil cutter - Profil cutter - Profil cutter horizontal - Profil cutter Kdodpfjmgc I Nex Adwsg - Profil cutter - Profil cutter Total el power 114 kw 400 V AC Need for suction 270 m3/min Need of compressed air 1000 L/ minMachine was in use until 15.08.2023 Payment: Prior to loading Delivery: ex. factory Rendalen - Norway Machine is located in Norway ( near to Trondheim) The machine is now disconnected, stored in dry and warm wearhouse, and are ready to be shipped. Rekman Maskin & Service - service of woodworking machines since 1986.

Condition: new, Year of construction: 2026, Cut-to-length and mitre saw type: ZS 200 N - 5 KW motor with machine stand, Machine via handwheel and worm gear (rear) Tiltable Saw blade diameter 520 mm, saw blade mounting hole 50 mm Saw blade speed: 2800 rpm 400 volt / 5 KW (S6/40%) motor with brake and automat. Star delta motor control Cutting width at 90 degrees: 420 mm Cutting width at 45 degrees: swiveled: 295 mm Cutting height at 90 degrees: 200 mm Cutting height at 45 degrees inclined: 140 mm Saw can be swiveled on one side up to approx. 25 degrees to an acute angle and tilted flat to the left up to 30 degrees Carbide circular saw blade 520x4.0/2.8 x 50 mm 60 WZ neg. for wood Kdedpfx Aok H Ic Usdwjg RLH-ST60 6.0 mtr. measuring length, mounting side: left Cross-cut fence / roller conveyor, heavy-duty design, Stop slide adjustable from the workstation via handwheel, electronic-digital dimension display, pneumatic clamping of stop slider, stop flap folds backwards, with steel rollers 60 mm diameter, roller spacing 200 mm, 400 mm roller width, with 4 support feet and connection piece: overall length: 6.7 mtr. Surcharge for digital electronic display unit type: FIAMA EP6 for 230 V mains operation, with electric on/off switch and socket. Powerful dark red LED display. Higher accuracy than the battery-powered crystal display RO-ST60 4.0 m long feed roller conveyor Mounting side: Right Heavy-duty design, steel rollers: 60 mm Diameter, roller spacing: 200 mm 400 mm roller width, 3 support feet and connection piece Location: From stock 54634 Bitburg - immediately available - Picture: similar. Machine is still in original packaging

Condition: good (used), Year of construction: 2007, Technical characteristics : - Max machinable length 3200 mm - Minimum machinable length 200 mm - Maximum width 200 mm - Minimum width 40 mm - Maximum workpiece height 130 mm - Depth with max Ø to tenon 320 mm: 105 mm - Tenoning carriage speed min / max 0/100 m / min - Min / max profiling speed: 3/15 m / min Tenoning: 1- end cut saw 5.5 hp (4 kW) Saw Ø 400 mm 2- tenoning router Counter bearing 50 x 620 mm 15 hp (11.3 kW) Max tool Ø 320 mm Axle stroke 575 mm Kdsdpfx Aot R T Hcodwog Automatic splinter guard 3- tenoning router Counter bearing 50 x 620 mm 15 hp (11.3 kW) Max tool Ø 320 mm Axle stroke 575 mm Automatic splinter guard Vertical positioning with continuous axis 4- Digital angular adjustment clamp Profiling: 5-: router to be profiled on the right Shaft 50 x 320 mm 10 hp (7.5 kW) Ø tools 130/240 mm Axle stroke 280 mm Time-delayed anti-shattering intervention during calibration Double direction of rotation Vertical and horizontal positioning with continuous axis 6-: router to be profiled on the right Shaft 50 x 320 mm 10 hp (7.5 kW) Ø tool 130/240 mm Axle stroke 280 mm Vertical and horizontal positioning with continuous axis 7-: router to be profiled on the right Shaft 50 x 320 mm 10 hp (7.5 kW) Ø tool 130/240 mm Vertical and horizontal positioning with continuous axis 8-: close-out recovery group Vertical and horizontal positioning with continuous axis Device for extracting the shutter 9-: lower horizontal shaft for groove Vertical and horizontal positioning with continuous axis 88.5 hp (66.4kW) 10-: digital guide 11-: Return of parts to the operator NO TOOLS AVAILABLE OBTAIN ADDITIONAL PHOTOS NOTE: SUBJECT TO CHANGES IN TECHNICAL DATA

Year of construction: 2022, condition: new, functionality: fully functional, Lauber wood dryer longitudinal ventilation Chamber with stacking trolley Net volume 7.2 m3 with wood temperature measuring point -> new / unused / original packaging -> available immediately (standard delivery time approx. 3/4 year) -> see detailed description in the photos Kodpfsmidtrex Adwodg -> collection, loading, etc. by buyer -> transportation, customs clearance and insurance by buyer

Condition: excellent (used), Planer 9 heads Working width - 20 cm Working height - 22 cm 5 pulleys in the table Heads 1 bottom 7.5 kW 2 right 11 kW 3 left 11 kW 4 right 11 kW 5 up to 11 kW 6 down 11 kW 7 up to 11 kW Kdedotrdwtopfx Adwog 8 down 11 kW 9 universal 11 kW PERFECT CONDITION!

Condition: good (used), Code: 0749 Brand: TAGLIABUE - COSTA LEVIGATRICI Model: TT 3 1300 Automatic sanding machine for worktops, furniture, panels, tables Technical data: Ksdpfxjh T Dzqj Adwedg Working width mm 1300 Max working thickness mm 130 Min working thickness mm 1 Composition: 1° Transversal belt - Motor Hp 15 - Electronic speed variator with display 2° Transversal belt - Motor Hp 15 - Electronic speed variator with display Transversal sanding belt size mm 1350 x 150 Chevron belt size mm 5510 x 140 Belt blowers Belt feed speed mt/min 5/25 Fixed table and mobile head for on-line set-up Panel cleaning rotary blowers Vacuum table Belt cleaning brush Infeed roller conveyor Installed power Kw 32 Compressed air 7 Atm Suction inlets: n° 2 diameter mm 200 - n° 2 diameter mm 150 - n° 2 diameter mm 100 Overall dimensions mmm 4400 x 2500 x 1600 h Weight kg 5000

Condition: used, Deburring and fine grinding machine for sheet metal / flat material, new The compact machining centre for deburring, slag removal, rust removal, oxide layer removal, edge rounding, fine grinding through to polishing metal surfaces. Machine is suitable for heavy-duty use. Due to the fixed working height, this machine can also be optimally integrated into a production line and is suitable for machining large parts. Working width: 650 - 1650 mm Maximum part weight: 2000 kg Wide belts with abrasive belt unwinding: 3250 mm Kdedjnah Taspfx Adwjg As standard with vacuum hold system, optional with magnetic hold system By using 3250 mm long abrasive belts, you get a uniformly smooth surface and reduce consumption costs, as these belts have a longer service life. Due to the modular design of the machines, it is possible to offer the optimal configuration for the customer's machining task. The machine structure can accommodate up to 5 internal machining units and 2 additional external machining units. The high rigidity of the machine structure and the feed table of this machine, combined with the advanced mechanics and electronics, make this series a universal machining centre for deburring and finishing. Please, contact us for getting more information and pictures on mail(at) or *

Condition: new, Year of construction: 2025, WOOD SHAVINGS MACHINE KÄLIN Hobeltechnik, mod. MPC-P • Quantity of fresh shavings by hour: 3.800 Kg/hour • Measures logs box: 2.800mm x 1100mm x 1.300mm • Max. log input length: 2.650mm • 2 removables symmetrical cutterheads. Lenght 1.140mm. Each one in 3 pieces of: - Diameter: 200mm - Length: 380mm - Number of knifes: 8 - Sharpening full cutterheads, without removing knifes!! • 2 extra removables symmetrical cutterheads, for replacement during sharpening. Super fast cutterheads change patented system!! • Power of the cutting heads: 90 kW/120 HP • Feeding speed controlled by ELECTRONICAL INVERTER: 6 to 36 m/min • Automatic control of the forward-charge ratio of the machine • Power of the feed motor: 15 kW/20 HP • Control System of the material level inside the logs box, to avoid working without logs • Cabinet and control panel. Touch screem to control the machine Kodpfxsvk Saxj Adwedg • Motorized conveyor belt for the wood shavings. 800mm x 5.000mm • Weight: 11.000 Kg • CE