Condition: excellent (used), Year of construction: 2010, functionality: fully functional, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, workpiece width (max.): 60 mm, The machine has been serviced and is in excellent condition. It is immediately ready for operation! Ijlhccsx Tqgbsqljal TECHNICAL DETAILS - Edge thickness (glued): max. 20 mm - Maximum gluing height: 60 mm - Maximum roll material thickness: 3 mm - Piece width: min. 60 mm - Maximum feed rate: up to 25 m/min - Feed: continuous - Electric height adjustment: available - Pressure system: upper belt pressure - Preheating zone: available - Granulate glue system: with pre-fabricated container - Glue pot: interchangeable/variable - Spray unit: available - Pre-milling unit: available - Trimming unit: with 2 motors - Milling stations: flush/radial/chamfer, 1 available - Corner rounding unit: with 2 motors - Edge scraper: profile and planer - Buffing unit: available - Strip magazine: available - Units: synchronized units with NC axis/axes - Machine version: left hand side - Quick-change units: available MACHINE DETAILS - Remote control: PowerControl PC 22 - Weight: 5,000 kg - Machine length: 7,845 mm - Standards: CE requirements EQUIPMENT - Special equipment: with nesting - New chains - HOMAG feed device with 2 rollers - HOMAG A 20 glue unit - HOMAG HL 84 - HOMAG FK 11 - HOMAG PN 10 profile pull scrape unit - HOMAG FA 11 finishing unit

Condition: used, Year of construction: 2019, operating hours: 3,488 h, functionality: fully functional, machine/vehicle number: 0-261-71-2252, type of input current: three-phase, input voltage: 400 V, input current: 22 A, input frequency: 50 Hz, We offer this used HOMAG EDGETEQ S-300 edgebander, year of construction 2019. Type: EDGETEQ S-300 Subtype: OPTIMAT KDF 440 C Machine number: 0-261-71-2252 Iajlsx Tt D Nshccqlel Wiring diagram: 0-261-71-2252 Year of manufacture: 2019 Supply voltage: 400Y/230 V Phases: 3 Phase Frequency: 50 Hz Maximum operating full load current: 22 A Fuse rating: 25 A Short circuit current rating: 5 kA rms symmetrical Control voltage: 24 V Enclosure type: NEMA 1 Largest motor current: 5.7 A Largest heater current: 2.3 A If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: used, Holz Her STREAMER 1057 XL FÜ + PU Iaelhcjx Ux U Ajcqlsl Edge thickness: 0.4 - 6 mm Modern control unit with selector switch for aggregate settings Fully automatic edge magazine for roll and strip material Glue application station GLU-JET cartridge + PU bonding Adhesive application via nozzle technology Touch-sensitive nozzle Workpiece height: 6-60 mm Automatic glue height adjustment High-quality 3-roller pressure unit, 1st roller motorized Pneumatic end trimming unit for roll and strip material up to 6 mm edge thickness Pneumatic adjustment of trimming saws from 0-10° angle Milling unit: flush trimming 6 mm, radius milling - bevel milling - 15° Corner copying unit - 3 mm edge thickness Scraper unit for chamfers and radii with 2 scraper holders Surface scraper unit - finish Buffing unit Spraying device in infeed and outfeed areas, as well as for PU Machine supplied with all working units/tools Machine is WORKSHOP TESTED First delivered in 2016 Available ex stock Lieboch

Condition: used, functionality: fully functional, Edgebanding unit Iaeloxfuh Dohccqljl End trimming unit Trimming unit 2nd trimming unit Sanding unit

Condition: excellent (used), CATALOG NUMBER 7730 TECHNICAL DATA Milling Machine: - Minimum width of workpieces: 50mm - Workpiece thickness: 16-40mm - Edge thickness: 0.5-3mm - Motor power: 1.1kW - Air requirement: 6 bar - Extraction nozzle: 60mm - Dimensions (L/W/H): 1900x850x1450mm - Weight: 290kg Trimming Unit: - Blade diameter: 150mm - Table size: 750x820mm - Motor power: 0.12kW / 2800rpm ADVANTAGES – Polish-made – Trimming unit – Profiled cutters included – Unpainted Iolhccsxa Egmsqloal – DTR documentation – Used milling machine, in very good condition Net price: 4500 PLN Net price: 1070 EUR depending on a rate of 4.2 EUR (Prices may vary with significant rate fluctuations)

Condition: ready for operation (used), Year of construction: 2002, This IMA Combima complete edge banding line with loading station was manufactured in 2002. A robust double-sided edgebander, it features a working width of 235 to 2600 mm and a length range of 200 to 2600 mm. Capable of speeds from 10 to 40 m/min, it includes jointing milling, a semi-automatic gluing unit with a 6-piece edge magazine, and both straight and profile trimming units. Consider the opportunity to buy this IMA Combima double sided edgebander. Contact us for more information about this machine. Ijlhcjx D Iq Njcqleal Application Types Edge Banding

Condition: used, machine/vehicle number: 007358, Type of edging: Thin edge, Thick edge, Solid wood Gluing System: EVA Hotmelt Premilling Unit: yes Corner Rounding Unit: yes Iaelhccqswlpl Tslel Maximum panel thickness: 60 mm Operating Units: 9 nr

Condition: new, Year of construction: 2026, Machine includes: Pre-milling, pre-heating, pre-melting, pressing, fine trimming, end cutting, corner rounding, cutter scraping, flat scraping, buffing Heavy duty machine body and most mechanical machine parts are proceeded by advanced CNC machines for higher stability and longer service life without deforming; Merges numerous functions in one machine, including pre-milling, pre-heating, pre-melt gluing Iajlhoxd Ubboccqlol system, snipping, end trimming, fine trimming with servo, corner trimming, scraping with servo, surface scraping and buffing, sprayers, edge banding work can be done in one process. Intelligent PC control, infeed fence, tape pressing rollers, fine trimming and scraping are servo adjust. Corner rounding pneumatic adjust. Machine Speed 16/20/24m/min; Nesting kit design, pre-drilled nesting hole friendly Fine trimming and Corner rounding by HSK25

Condition: excellent (used), edge banding machine, very well maintained, works very well, the adhesive is on granules, year of manufacture 2014. ideal for a small space, has the following features. pre-milling, end cutting, top and bottom milling with radius, radius tickling, straight tickling Iaelsyah Tdohccqlel

Condition: excellent (used), Year of construction: 2018, Smart Touch Numerical Control with Sintra HD Software Panel height mm 10 – 60 Solid mm 22 Pvc/Abs mm 3 Feed speed up to mt/min 25 Working height electronically adjustable by N.C. Motorized and electronically adjustable panel support guide by N.C. Anti-adhesive group Rectifying group with 2 motors electronically adjustable by N.C. Reel holder plate with n° 1 position Gluing group for EVA hot melt glue with glue pot End trimming group with 2 motors with dynamic suction system that follows the blades in each of its movements. Staggered trimming/cornering unit with 2 motors electronically adjustable by C.N Anti-stick unit Rounding unit with 2 multifunction motors (cornering unit + rounding unit) Electronic edge scraping unit electronically adjustable by C.N Glue scraping unit Brush unit “SP-501” Iaolhewlbxlsccqlel Automatic piece return system with Winner 4A bridge unloading

Condition: excellent (used), CATALOG NUMBER 7729 TECHNICAL DATA Equipment: - Tape holder - Glue tank (granulate) - Tape feeder - Guillotine – pre-cutting the edging - Pressure rollers 2 pcs Islexaprgjhccqlsal - Min. width of processed components: 50mm - Thickness of processed components: 10-40mm - Min. internal radius: 50mm - Angled gluing with 1mm thick edging, 0-45° - Edge thickness: 0.3-3mm - Electric feed - Total power: 2kW - Compressed air pressure: 6-7 bar - Dimensions (L/W/H): 1700x1300x1550mm - Weight: 310kg ADVANTAGES – Made in Poland – Unpainted – DTR technical documentation – Very good condition – used edge banding machine Net price: PLN 6500 Net price: EUR 1550 (exchange rate: 4.2 EUR) (Prices may vary depending on larger fluctuations)

Condition: used, Year of construction: 2010, functionality: fully functional, – Very good condition – Year of manufacture: 2010 – Operating and maintenance documentation (DTR) available TECHNICAL PARAMETERS: – Edge thickness min. - max.: 0.4 – 3.0 mm – Workpiece thickness min. - max.: 10 – 45 mm – Saw trimming unit – Milling unit for trimming excess edge tape flush or with a profile – Designed to remove excess edge tape at the top and bottom edges of the panel – Flush milling – Milling of the edge tape at an angle or radius in a single work cycle – Edge overhang milling: Ø 70 mm, Z 6, a=15°, R=2 mm Iajlhccsw H Rzxeqlel – INSPECTIONS CARRIED OUT BY FELDER SERVICE – COMPACT DIMENSIONS – PRECISE AND VERY EASY TO USE – Table dimensions: 2000 x 300 mm – Air supply requirement: 6 Bar – Power supply: 400 V – Power: 3.2 kW – Glue application roller and glue tank – Grooved glue application roller ensures uniform glue coverage on the edge of the workpiece – Feed speed: 9 m/min – Overall dimensions (L/W/H): 2000 x 1260 x 650 mm – Net weight: 360 kg

Condition: used, machine/vehicle number: 008325, Position 1: Single Edgebanders HOMAG-KDF 860 C Position 2: Panel Return Systems HOMAG-KDF 860 C Ijlhex Hpkleccqlsal

Condition: new, Year of construction: 2026, functionality: fully functional, The Nanxing NB875A is a professional 2-in-1 edge banding solution that combines straight edge banding and Soft Forming technology in a single machine – perfect for handleless doors and modern furniture fronts. Equipped with a complete set of pre-milling, heating, pressing, and finishing units, NB875A delivers flexibility, high productivity, and premium edge quality. Its fully automated control system and intuitive software allow fast switching between 14 different profiles (full C, left/right J, concave center, concave left/right, W-shaped, diamond profiles, etc.). Key Highlights Multi-functional machine for both straight and softforming edge banding in one pass. 14 profiles available, automatically switchable via servo control. Energy-saving function – automatic standby mode after idle time. Advanced industrial control PC with 24” touchscreen, online connectivity, optional barcode reader. Fully enclosed machine with sound-absorbing material for low-noise operation. CE certified, international brand electrical components. Working Units & Equipment Pre-milling unit with 2 electro-pneumatic motors, H35 mm cutters. 2 sets of J & C profile milling units (4 motors – 7.5 kW + 3.5 kW) with automatic switching. Panel pre-heating + 2 glue application units (panel + edge). Softforming & pressing station with precision steel rollers and band pre-heating system. Servo-driven tape feed & pneumatic end trimming (Ø180×3.5×60T saws, 12,000 rpm). Rough & fine trimming units, radius scraping & flat scraping. Double buffing units for a perfect glossy finish. Independent dust extraction hoods (9 × Ø125 mm) for all processing units. Automatic lubrication system and full safety protection (panel thickness detection, feed monitoring, E-STOP). Technical Specifications Minimum panel size: 300 × 150 mm (central concave ≥ 400 mm) Panel thickness: 18 mm (straight), 18–25 mm (softforming) Edge band thickness: 0.5–0.6 mm (softforming), 0.5–1.2 mm (straight) Feed speed: 8 m/min Power supply: 380V / 50Hz Air pressure: 0.7 MPa Installed power: 68 kW Net weight: approx. 6,000 kg Machine dimensions: 11,015 × 1,000 × 1,940 mm Applications Production of handleless doors for kitchens, wardrobes, and bathroom furniture Complex edge banding operations in medium and large-scale production Premium edge finish with invisible glue line Advantages for Manufacturers Maximum versatility: one machine for all straight & softforming edge banding profiles. Superior finish: smooth edges, perfect glue adhesion. High efficiency: automatic operation, quick profile changeover. Islhjxcwrmsccqleal Cost reduction: fewer machines required, minimal downtime.

Condition: excellent (used), edge banding machine, very well maintained, works very well, the adhesive is on granules, year of manufacture 2014. ideal for a small space, has the following features. pre-milling, end cutting, top and bottom milling with radius, radius tickling, straight tickling Ijlhcsyah S Tjcqljal

Condition: used, Year of construction: 1996, Plate running direction: from operator to the left Max. edge thickness: 8.0 mm Min. workpiece width: 70 mm Feed speed: 11 m/min Heating-up time: 4.5 min Automatic roll magazine: Yes Cutting shears up to: 0.2 - 3.0 mm Individual edge feed: Yes Automatic gluing: Glue pot with granulate on top Iaolhcexwdp Uecqlel Cut-off saw: fixed at 90° Flush-milling unit: Yes Combination milling unit: Yes Aggregate display: glue display Control type: manual Operation: selector switch / push buttons Travel device: Yes Protective hood: Yes Working height or infeed table height: 870 mm Approx. weight: 670 kg Dimensions: 3600 x 1400 x 1200 mm Motor power: 11 kW Extraction diameter: 120 mm Storage location: Supplier

Condition: excellent (used), Catalogue number 7843 TECHNICAL DATA - Table dimensions: 2050x350mm - Table dimensions with support: 2050x940mm - Min. workpiece length: 120mm - Min. workpiece width: 90mm - Workpiece thickness range: 10-45mm - Edge width range: 12-48mm - Edge thickness range: 0.4-3mm - Feed speed: 6.4m/min - Power consumption: 2.3kW - Required air pressure: 0.7 Mpa Islhccqsx A Dt Doljal - Spindle speed: 10,000 rpm - Extraction connector: 2x100mm - Heating power: 1250W - Dimensions (L/W/H): 2400x1300x1130mm - Weight: 360kg ADVANTAGES – Unpainted – With polisher – Used machine, in very good condition Net price: 12,000 PLN Net price: 2,860 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR (In case of significant exchange rate fluctuations, the price may change)

Condition: used, Compact edgebanding machine Hebrock EURO 3001 for precise edging of panel material with edge bands. The machine enables clean edge processing through automatic glue application, pressing rollers and post-processing aggregates. Ideal for furniture and interior construction. Technical data subject to change. Unit 1: Glue application Unit 2: caps Unit 3: Flush milling workpiece height: approx. 10 – 40 mm Ijlhccexdc D Roqljal edge thickness: max. approx. 12 mm feed rate: approx. 10 m/min

Condition: ready for operation (used), Year of construction: 2019, This SCM Olimpic K560 edgebander was manufactured in 2019. It features a 7" touch screen display with Touch 7 electronic control, supports edging thickness from 0.4 to 3 mm, and handles panel thicknesses from 8 to 60 mm. The machine offers a feed speed of 12-14 m/min and includes a hot air edge banding system. Contact us for more information. • Machine Condition: Good condition • 7" touch screen display (16:9) with Touch 7 electronic control • Edging Thickness: 0.4 – 3 mm • Panel Thickness: 8 – 60 mm • Minimum Panel Length: 140 mm Islhcoyabq Ascqlsal • Minimum Panel Width: 100 mm • Feed Speed: 12 – 14 m/min • Hot Air Edge Banding System

Condition: used, Year of construction: 2012, Basic machine Olimpic K 800 "T-ERL" (47) 1 pc. BASIC EQUIPMENT: - Ribbed steel machine frame with tubular reinforcements for optimal work unit support - Pivoting control panel - Support roller conveyor with ball bushing guides along the entire machine length - Protective and sound-absorbing hood with separate doors between the gluing and finishing units - Extractor nozzles located on the sound-absorbing hood - Electrical system with lockable main switch - Emergency/stop buttons at the inlet and outlet - Inverter for electric spindles. PLATE FEED SYSTEM - Feed chain with rubber glide shoes, mounted on a 1 1/4-inch industrial chain with a high friction coefficient - The chain slides on two guides made of hardened and ground steel, one round and one flat, to guarantee straight feed and protect against lateral misalignment. --- Automatic central lubrication of the feed chain - The upper pressure beam is made of thick-walled steel construction. Complete with double rows of bearing rollers and protective device for the printing rollers - manual lifting of the printing unit with automatic working unit positioning when changing the plate thickness - mech. Digital display for checking the selected panel thickness. ORION 100 CONTROL SYSTEM. Control device complete with PLC, allows fast, easy, and error-free execution of custom processing programs (max. 60 programs). Manages the pneumatic positioning of the units, if present on the machine. (The control system does not include pneumatic positioning). - Alphanumeric keyboard and display - Function keys for quick control of the processing units - Ambient temperature range from 0 to +45° C. MAIN FUNCTIONS - Control of the processing units and automatic activation of the motors - Control and regulation of the glue pot temperature - Selection of longitudinal and transverse processing without program change - Simple and guided diagnostics for easy troubleshooting - Statistics on absolute data and individual processing: number of pieces, edge consumption, total chain feed distance - Unit of measurement selectable in mm or inches. Technical data OLIMPIC K800 T-ER L Edge thickness: 0.4 to 8 mm Max. gluing thickness of the roll edge: 3 mmFeed speed: 12/18 m/minWorking height: 8 to 60 mmMax. dimensions of the edge cut: 135 mm²Turntable diameter: 780 mmMax. oversize compared to the panel thickness: 4 (2+2) mmMin. panel width (with 210 mm min. length): 55 mmMin. panel length (with 100 mm min. width) - with strip or roll edges max. 3 mm: 140 mm - with solid wood edges: 200 mmMin. distance between consecutive panels at 11 (16) m/min: 750 (850) Standard equipment - Pre-milling unit in the infeed RT-E- Gluing station VC-800- Trimming unit KSEL- Flush trimming unit, tiltable RI/800- Rounding unit ROUND K- Scraper unit RAS-V- ½ free space for surface scraper- 1 S free space for surface scraper or Universal milling or buffing unit - 1 free space for air nozzle unit. European safety regulations (C.E. mark). 1 unit. Voltage 400 EU. 1 unit. Frequency 50 Hz. 1 unit. "Autoset" for ER2, T-ERS, and T-ERL models. 1 unit. Allows all necessary adjustments to be made from the control panel for each machining change. Includes: - time-controlled pressure unit - pneumatic and independent pivoting of the mitre saw blades (front/rear) - pneumatic remote adjustment for the RI/800 flush trimming unit. Iaolhccqjx Twdtelsl

Condition: excellent (used), CATALOG NUMBER: 7404 Islhcox Tgv Socqloal TECHNICAL DATA - Minimum workpiece thickness: 16mm - Maximum workpiece thickness: 60mm - Height to table surface: 920mm - Motor power: 1.2kW - Voltage: 400V - Disc – guillotine – feed rollers for tape – glue tank – 3 guide rollers (first one is the drive roller) - Worktable: 1600x670mm - Dimensions (L/W/H): 1600x1400x1100mm - Weight: 170kg ADVANTAGES – Polish manufacture – Suitable for edging both straight and curved edges – Used machine, in very good condition Net price: 5,900 PLN Net price: 1,400 EUR (based on 4.2 PLN/EUR exchange rate) (Prices may change with significant fluctuations)

Condition: ready for operation (used), Year of construction: 2019, This SCM E10 edgebander was manufactured in 2019. It features a 0.4 to 3 mm edgebanding thickness capacity and can handle panel heights from 8 to 80 mm. The machine supports minimum panel dimensions of 50 mm in width and 210 mm in length. It operates with two feed speeds of 4 and 8 m/min and a maximum temperature range of 140 to 220 degrees C. Installed motor power is 3.5 kW. Contact us for more information about this machine. • Edgebanding Thickness Capacity: 0.4 to 3 mm • Thickness of Edges with Shear Device: • (80 mm height) 0.4 to 1.5 mm Iaolsyabmkshccqlol • (50 mm height) 0.4 to 2.5 mm • (45 mm height) 0.4 to 3 mm • Panel Height Capacity: 8 to 80 mm • Edge Height: 10 to 83 mm • Minimum Panel Width: 50 mm • Minimum Panel Length: 210 mm • Minimum Internal Radius with 0.4 mm Edgebanding: • Concave: 25 mm • Convex: 5 mm • Feed Speeds: 4 and 8 m/min • Maximum Operating Temperature: 140 to 220 degrees C • Installed Motor Power: 35 kW • Overall Dimensions: 39.37" x 29.13" x 43.3"

Condition: new, Catalogue No.: HZ014 – Pre-milling Iaolhccjx S Iypjqlel – Corner rounding – Brand new machine in stock – CE certificate – Professional grade TECHNICAL DATA Panel thickness: 8–45 mm Edge thickness: 0.4–3 mm Min. panel width: 90 mm Min. panel length: 170 mm Feed speed: 9 m/min Pre-milling speed: 12,000 rpm Front/rear milling: 12,000 rpm Top/bottom milling: 12,000 rpm Corner rounding: 12,000 rpm Polishing: 3,000 rpm Feed motor power: 1.13 kW Glue tank heating power: 1.315 kW Pre-milling motor power: 1.5 kW Preheating power: 0.4 kW Glue spindle power: 0.25 kW Front/rear milling motor power: 0.22 kW Top/bottom milling motor power: 2 × 0.37 kW Corner rounding motor power: 0.37 kW Polishing motors: 0.12 kW and 0.18 kW Total motor power: 6.16 kW Working table height: 960 mm Extended support width: 560 mm Extraction port: 3 × 125 mm Dimensions (L × W × H): 3731 × 720 × 1636 mm Weight: 915 kg Holzing G-MAX 480 straight-line edge bander with pre-milling, saw cutting, top-bottom milling, corner rounding, radius scraper and polisher ensures a high-quality finish on the workpiece. It handles edge banding from coils up to 3 mm thick and strips up to 4 mm thick. The machine is equipped with a 1.2 kg capacity glue tank. Net price: 98,000 PLN Net price: 23,300 EUR based on an exchange rate of 4.2 EUR (Prices may change in the event of significant fluctuations)

Condition: ready for operation (used), Year of construction: 2012, This IMA Novimat Concept / I / G80 / 440 / R3 edgebander was manufactured in 2012. It features a robust automatic edge banding and post-processing system, including a workpiece returning system for enhanced productivity. Capable of handling edge materials from 0.3 mm to 3 mm and workpiece thicknesses up to 60 mm. Equipped with a pneumatic quick-lock system and electronic temperature control for precise glue application. Consider the opportunity to buy this IMA Novimat Concept / I / G80 / 440 / R3 edgebander. Contact us for more information. Additional equipment • Joint Milling Unit: 2 motors, each 4.0 kW, 8800 RPM • Heater: Preheats workpiece edges up to 60 mm • Glue Application: Handles edges up to 3 mm • End Trimming Unit: 2 motors, 660 kW Iaelhccjx U U D Teqlsl • Additional Units: Milling, Multi-Profile Milling, Contour Milling, Multi-Profile Scraper, and Scraper Units; Buffing Unit • Automatic Quickmelt hot glue feeder • Board Return System with powered roller conveyors, cross conveyor, transport belt, angle transfer, air-cushion tables, and safety fence Machine Benefits Technical Machine Benefits • Minimum workpiece length: 150 mm / minimum workpiece width: 65 mm / minimum workpiece thickness: 8 mm / maximum workpiece thickness: 60 mm / smallest workpiece: 150 mm x 150 mm or 65 mm x 300 mm Extra Information This machine is configured for efficient edge banding and post-processing with a robust set of features and support for various workpiece sizes. It is immediately available for production use.

Condition: ready for operation (used), Year of construction: 2010, This IMA Advantage 310 edgebander was manufactured in 2010. It handles workpieces from 150 mm in length and 65 mm in width, with thicknesses up to 60 mm. It's equipped for various materials including chipboard and MDF, using melamine, paper, foil, or veneer edges. Features include a gluing unit, cutting unit, and a buffing unit, enhancing finishing processes. Consider the opportunity to buy this IMA Advantage 310 edgebander. Contact us for more information about this machine. Machine Benefits Technical Machine Benefits • Minimum workpiece length: 150 mm • Minimum workpiece width: 65 mm (with max thickness of 25 mm), 150 mm • Workpiece thickness: min. 8 mm, 12 mm with profile scraper blades; max. 40 mm (mfa 08346), 60 mm (skf) • Smallest workpiece: 65 x 300 mm / 150 x 150 x 19 mm • Machining allowance per workpiece edge: 0 - 5 mm • Workpiece shape: rectangular • Material: chipboard, mdf • Surface material: direct coating (melamine resin paper), paper, foil, veneer Extra Information Edging Material Roll material without foil: Paper edges & plastic edges: 0.3 - 3.0 mm Veneer edges: 0.5 - 3.0 mm Max. edge cross-section: 150 - 180 mm² Cut-to-length edge strips: Strips: 3.0 - 8.0 mm Max. strip cross-section: 520 mm² Edge height: Min. 12 mm, max. 65 mm Max. upper edge overhang: 2 mm Edge profiles: Paper edge: Approx. 0.4 mm, bevel 15° Plastic edge up to 3.0 mm, depending on radius tool Milling strip flush up to 8 mm Machine Constant workpiece projection from the chain track: 35 mm + edge thickness Max. cutting cross-section: 520 mm² Passage width: Min. 65 mm (with 35 mm projection) Min. workpiece length in feed direction: 150 mm Basic height (top edge of chain track): 940 mm Iolhcex U U Dtocqlsal Aggregate side: Left in feed direction Pneumatic connection: Approx. 7 - 8 bar Joining Unit 08.379 and Blow Nozzle 2 motors 4 kW each, 9000 rpm Gluing Unit 283.1513 Glue dispenser 0.8 l, 60 mm high Suitable for hot melt or PU glue With single roller/strip magazine, roller diameter 800 mm 3 main pressure rollers and 3 pressure rollers Cutting Unit 08.415 Pneumatically swivels to 0° or 8 2 motors, 12,000 rpm 2 HM cross-cut saw blades Copy Trimming Unit SKF-L 4 motors, 12,000 rpm Profile length in throughfeed direction: Max. approx. 50 mm Workpiece thickness: Max. 60 mm Working speed: Max. approx. 20 m/min Distance between 2 workpieces: Min. approx. 400 mm Profile Scraper Unit 08.519 For rescraping an upper and lower milled quarter circle profile Self-Scanning Scraper Unit 08.521 For removing hot melt adhesive residue from the edge area of the top and bottom of workpieces Buffing Unit 08.617-2 Upper and lower motor: 180 W, 1400 rpm 2 polishing wheels 50 x 160 x 19 mm