Fine Blanking Press

FEINTOOL HFA 320

Condition: excellent (used), Year of construction: 2018, total length: 9,800 mm, total width: 4,000 mm, feed length X-axis: 3,500 mm, feed length Y-axis: 1,100 mm, feed length Z-axis: 1,100 mm, feed rate X-axis: 30,000 m/min, feed rate Z-axis: 5,000 m/min, table length: 3,000 mm, table load: 6,000 kg, table width: 1,200 mm, power: 22 kW (29.91 HP), Surface grinder Ziersch - Z1030 MACH-ID 9597 Make: Ziersch Type: Z1030 Control: Mitsubishi Touch Year: 2018 X - Travel: 3500mm Y - Travel: 1100mm Z - Travel: 1100mm Table Length: 3000mm Table Width: 1200mm Table load: 6000 Hjdpfx Aley En Dneweu Feed rate X-Axis: 30000mm/min. Feed rate Z-Axis: 5000mm/min. Grinding stone dimensions:500 x 100 x 203mm Power: 22kW Speeds: 3000Rpm Cooling system: yes Feed rate Y-Axis: 3000mm/min. Length: 9800mm Width: 4000mm Height: 4500mm Weight: 27500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2017, operating hours: 56,681 h, laser power: 4 W, 2017 Laser cutting machine with changing table and pipe cutting function. DURMA HD-FL 3015 BH / IPG 4kW – Manufacturer: DURMA Hsdjvyhczepfx Alwju – Model: HD-FL 3015 III BH-IPG 4kW – Year of manufacture: 2017 – Laser source: IPG – Control system: SIEMENS + CAD software + nesting software – Operating hours: 56,681 h Technical data: – Working area: 3000 x 1500 mm – Pipe cutting diameter: Ø 12 – 400 mm – Laser power: 4000 W (fiber laser) Maximum thickness parameters of cutting materials: – Black steel: up to 12 mm – Stainless steel: up to 10 mm – Aluminum: up to 10 mm – Copper: up to 4 mm – Brass: up to 6 mm Additional functions: – IPG fiber laser resonator – Water cooling system for laser source and cutting head – Extraction and filtration system under and above the laser – Double table system – Pipe laser with 4-point chuck and can cut up to 6 m – CAD software – Nesting software – Pipe laser software – Very good condition, annual service performed 2024.12. If you have any more questions, we will be happy to answer.

Condition: used, Year of construction: 2019, functionality: fully functional, table length: 8,000 mm, table width: 2,540 mm, overall weight: 8,000 kg, sheet thickness steel (max.): 100 mm, cutting length (max.): 8,000 mm, cutting width (max.): 2,540 mm, drill diameter: 40 mm, FICEP TIPO G25LG - CNC PLATE PROCESSING LINE (DRILLING, MILLING, THERMAL CUTTING) | YEAR 2019 The Ficep Tipo G25LG is a CNC plate processing line for combined drilling, milling, tapping and thermal cutting of steel plates in structural steel fabrication. Built in 2019 - a young machine in its class on the used market. All processes run in a single pass on a rigid double-bridge gantry frame. CONDITION & REFURBISHMENT Refurbished and inspected by a certified technician, ready for operation. - The exact scope of reconditioning varies from machine to machine and is disclosed individually upon serious interest. - Viewing possible by arrangement (machine reconditioned - no demonstration under power). FUNCTION & APPLICATION The vertical mono drilling unit with automatic tool changer (ISO 40) performs drilling, milling, tapping, centre-punching and countersinking. The Hypertherm XPR300 plasma torch and the integrated oxy-fuel cutting unit handle thermal cutting - from thin sheet to heavy plate. The line is operated via the Ficep Pegaso CNC control. Infeed and outfeed roller conveyors with material transfer (8 m each) ensure continuous material flow. Typical applications: structural steel fabrication, steel trading and plant engineering. TECHNICAL DATA - Manufacturer: Ficep | Model: Tipo G25LG | Year: 2019 | Serial number: 36098 - Machine type: CNC plate processing line (drilling / milling / thermal cutting) - Condition: used, refurbished by certified technician - Frame design: double-bridge gantry frame, welded | Machine weight: 8,000 kg - Plate width: max. approx. 2,540 mm, min. 200 mm - Plate thickness: max. 45 mm (plasma cutting), max. 100 mm (drilling) - Drilling heads: 1 (vertical mono drilling unit) | Tool holder: ISO 40 - Max. drilling diameter: 40 mm | Max. drilling/milling depth: 100 mm - Max. spindle speed: 7,000 rpm | Spindle power: 15 kW - Plasma cutting torch (straight): 1 | Plasma source: Hypertherm XPR300 | 300 A - Oxy-fuel cutting unit: included - CNC control: Ficep Pegaso CNC - Processes: drilling, milling (incl. straight/curved slots, Y/J weld-edge preparation), tapping, centre-punching, countersinking, marking, scribing, straight plasma cutting, oxy-fuel cutting On request (to be confirmed bindingly during inspection): processing length, tool magazine stations, min. plate thickness for drilling, min. drilling diameter, pass line height, longitudinal and cross positioning speeds, connected load and machine dimensions. SCOPE OF DELIVERY - 1 x Ficep Tipo G25LG CNC drilling, milling and thermal cutting line (year 2019) - 1 x Ficep Pegaso CNC control - 1 x Vertical mono drilling unit with automatic tool changer (ISO 40) - 1 x Plasma cutting torch (straight) | 1 x Hypertherm XPR300 plasma source (300 A) Hodpfxou Dw I Ee Alwju - 1 x Oxy-fuel cutting unit - 1 x Infeed roller conveyor with material transfer (8 m) | 1 x Outfeed roller conveyor (8 m) - 1 x Extraction system for plasma cutting LOGISTICS & LOCATION Location: Ulft (Netherlands), directly at the German border. Dismantling, transport, installation and commissioning by ASM by arrangement - individually calculated upon request. ABOUT ASM Arendsen Steel Machinery (ASM): specialist for refurbished Ficep structural-steel machinery. Further machines on request. CONTACT / INQUIRY Viewing by arrangement | Price on request. Sale exclusively to commercial customers (B2B).

Condition: good (used), Year of construction: 2000, gear diameter: 449 mm, Equipped with: Fanuc 150MB CNC Control Dry Cutting Cutter Shroud Chip Evacuation System Auto Doors Hydraulic System Lubrication System Work light Stack Light Specifications: Largest Speed Ratio: 10:01 Work Area (Continuous): Largest Depth of Teeth: 15.24 mm Largest Width of Tooth Face: 50.8 mm Work Area Axis: Horizontal Movement X Axis: -114 - 178 mm Vertical Movement Y Axis: -178 - 190 mm Movement of the Carriage Baseplate Z-Axis: -10.16 - 500 mm Workpiece Headstock Swiveling Range B-Axis: -3 - 90 Degree Maximum Distance Machine Center to Spindle Side: 165 mm Number of Teeth: 5-200 Inclusive Max. Gear Pitch Dia. of Typical 35 Deg. Spiral Angle Gear Using Max. Cutter Dia. 12" Cutter at the Following Ratios: Hjdperuakgjfx Alwju Face Milling 1 x 1 - 13.5" - 342.9mm 2 x 1 - 16.0" - 406.4mm 5 x 1 - 17.7" - 450.0mm Face Hobbing (210mm Dia. Cutter) 1 x 1 - 10.560" - 268.22mm 2 x 1 - 10.286" - 275.00mm 5 x 1 - 11.810" - 300.00mm Milling Head Diameter: Helixact: 100,125,169,200,250,320mm Continuous Gumption Procedure, Teichloroethylene: 102 - 210 mm Workpiece Spindle: Drilling of Large Diameters: 5 3/64" Cone Upward Gradient on 304.8 mm (1 Foot): 21/32" Deep One of the Cone: 5.29" Diameter of the Whole Spindle Perforating: 3.35" Speeds: B-Axle Workpiece Headstock Drag Axis: 30 Degrees A-Axle Workpiece Spindle Number of Revolutions: 0 83 min-1 X-Axis Horizontal: 80 mm/sec Y-Axis Vertically: 80 mm/sec Z-Axis Carriage Baseplate: 80 mm/sec Space Requirement L x W x H (Approximate): 4.75 x 3.40 x 2.54m / 188" x 134" x 100" Machine Weight (Approximate): 10980 kg / 24,156#

Condition: new, Year of construction: 2026, functionality: fully functional, AM-20 Laboratory/Pilot Extruder with Wide-Slot/Film Die and Calender Unit Compact, vertical laboratory and pilot extruder AM-20 suitable for processing various plastics such as PP, PE, PS, ABS, PVC and other plastic granulates. The machine is equipped with a wide-slot die/film die, making it ideal for film extrusion, material testing, color and mixing trials, as well as development applications in laboratory and pilot plant environments. Additionally, calendering equipment is included, as shown in the photos. Technical data: • Model: AM-20 • Voltage: 110 V / 220 V • Input voltage: 2 x 220 V • Power: 1000 W • Screw diameter: 20 mm • L/D ratio: 15:1 • Throughput: approx. 500–1000 g/h • Dimensions: 45 x 25 x 60 cm Hedsyyw T Uopfx Alwou Suitable for: • Film extrusion • Laboratory and pilot-scale trials • Material development • Color and mixing tests

Condition: used, Year of construction: 1973, spindle diameter 130 mm x-travel 3000 mm y-travel 2000 mm total power requirement 4,5 kW weight of the machine ca. 30 t Spindle Ø 130 mm Spindle taper SK 50 Working range: X = column, longitudinal 3,000 mm Y = headstock, vertical 2,000 mm Z = spindle stroke 1,000 mm Lower table 3,300 x 2.400 mm Max. weight on table 10 tons/m² Min./ max position of work spindle above table 770 / 2,770 mm Feeds 0.9 - 2,000 mm/min Quick feed for headstock and column 5,000 mm/min Quill feed 0.5 - 1,200 mm/min Hjdpfx Alst Hwt Ssweu Speed range, partially infinitely variable 4.5 - 1,250 rpm Weight, approx. 30,000 kg Accessories / Special Features * HEIDENHAIN Digital Display for 3 axes. * Hardened guideways. * Ball screw spindles. * Infinitely variable spindle speeds and feeds. Feeds can be individually driven with motor. * Moving operating platform. * Hanging control panel. * Manual operating control. * Platform. * Hydrostatics in the column displacement. * Mounting plate 3,200 x 2,500 mm, planed, with t-slots. * Top table approx. 1,400 x 2,600 x height 900 mm, one face is handled. * Hydraulic clamping of column and slides. * Motor driven tool clamp. * Lots of accessories, including tool holders with and without tools, separate chip extractor, clamping aids, 1 angle plate, and other plates. Lots of other accessories. This is a strong machine which is very suitable for heavy cuts and therefore ideal for the machine tool industry and for tool manufacturers. Condition : Good. Machine can soon be inspected under power. Delivery : Ex stock as inspected Payment : Net, after conclusion of contract Thank you for your interest. We have other horizontal borers on stock. Please let us know what you need.

Condition: used, Year of construction: 2009, greates pass round over bed 640 mm swing diameter over face slide 435 mm control SIEMENS - 840 D turning speed range 3 - 2.500 U/min centre distance 2.000 mm spindle bore 70 mm spindle diameter in front bearing 100 mm Lathe - cycle-controlled | VDF-BOERHRINGER - DUS 630 ti Hedpfx Aezaf Hnelwju The machine is in good condition. Please note that the technical details were added from comparable machines. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: DUS630ti | DUS 630ti | DUS 630 ti

Condition: ready for operation (used), Year of construction: 1970, functionality: fully functional, shaft length under head: 30 mm, section length (max.): 52 mm, Hilgeland CH1 KHA double-acting press Year of construction 1970 Hjdpfxsur N Dao Alwou The machine is ready for immediate use!

Condition: excellent (used), Year of construction: 2021, operating hours: 3,000 h, travel distance X-axis: 6,100 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 950 mm, CNC Travelling Column Milling Machine – Fully Retrofitted by REM (2021) Powerful and versatile heavy-duty milling machine, completely modernized by REM specialists in 2021 with state-of-the-art Heidenhain TNC 320 control. Ready for immediate production use. KEY SPECIFICATIONS: • X-axis (transversal travel): 6,000 mm • Y-axis (vertical head travel): 2,000 mm • Z-axis (axial slide travel): 950 mm • Dual-spindle head | Head rotation: 360° • Spindle speed: 1,000 – 4,000 rpm • Spindle taper: ISO 50 (automatic locking/unlocking) • Head dimensions: 290 × 290 mm • Spindle motor power: 15 kW (DC) • Machine weight: approx. 32 tonnes • CNC Control: Heidenhain TNC 320 WHY BUY FROM REM? ✔ Machine fully inspected and tested in working conditions ✔ Modern CNC retrofit – new electrics, new drives ✔ Documentation and technical support available ✔ Export worldwide | Competitive shipping Ideal for heavy component machining in aerospace, energy, and heavy industry. Hedpfx Alen D N H Toweu Contact us today for full technical specifications, photos, and video demonstration.

Condition: good (used), Year of construction: 2001, CNC turning machine Manufacturer: OKUMA Type: LB-250T Model: OSP-U10L Hedjk Hz Iwspfx Alweu YEAR OF MANUFACTURE: 2001 2-axis CNC turning machine with robotic loading Description: Two-axis X-Z turning machine for short workpieces, equipped with a robotic workpiece magazine X-AXIS: 180 mm Z-AXIS: 325 mm Spindle speed: 4500 rpm Coolant system and chip conveyor