Bolster plate

GERD WOLFF Aufspannwinkel 1x 0,7x 2 Meter

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: EVO, controller model: EVO 4 AXIS 15", number of rollers: 4, roller (top) diameter: 300 mm, roller diameter: 300 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 1,250 mm, sheet thickness (max.): 30 mm, sheet thickness steel (max.): 30 mm, sheet thickness stainless steel (max.): 25 mm, overall weight: 17,000 kg, total length: 5,500 mm, total width: 2,000 mm, total height: 2,100 mm, power: 18.5 kW (25.15 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, 4roll hydraulic plate bending machine rated capacity 3000x35 mm MODEL MG M3035 , used year 2024 machine as new with warranty included Planetary dual pre-pinch Performance Capacity: Plate width 3000 mm plate thickness rolling 30 mm pre-bend 25 mm minimum rolling diameter ID 350 mm max open width plate feed 3100 mm special top roll reduced size 300 mm to achieve rolling ID 350 mm Power electric motor 18.5kw on hydraulic unit Vac 400/50 -480/60 Installed configuration Hardened rolls high surface strength Conical plate rolling, cone bending Electric console remoted on wheels with joysticks and readout CNC programmable 4 axis controller touch screen 15” Setup virtual infinite rolling programs with teach-in mode and cad/cam operator interface --- Hydraulic motorized driven the central rolls Pre-pinch load adjustable for pre-bend Drop-end top roll front open unloading closed shells Re-rolling system for welded shells calibration. Safety and emergency stop Iedoy Tbf Iepfx Aiyebb Manuals and schematics machine dimension 5500x2000x2100 mm -weight 17ton --- Additional accessories available with the machine See layout drawing in enclosed nr.1 central support hydraulic 2.2 ton capacity to support large shell dia up to 4,5 meters id nr.1 side support hydraulic left side 2.2 ton double arm nr. 1 side support hydraulic right side 2.2ton double arm

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, sheet thickness (max.): 60 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), Equipment: cone bending device, documentation/manual, 4 roll plate bender HAEUSLER - VRM-hy Ibedjzbqqujpfx Aiysb MACH-ID 9638 Make: HAEUSLER Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls 570 / 500 / 430 mm Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1978, condition: ready for operation (used), A Haeusler CNC large-format 4-roll plate bending machine is available. Number of rolls: 4, Roll width: 3050mm, Max. prebending plate width: 3000mm, Max. prebending plate thickness: 60mm, Max. rolling capacity at max. plate width and 3500mm bending diameter: 70mm, Roll diameter top/bottom/side: 620mm/600mm/500mm, Max. top roll load: 12000kN, Operating speed: 4m/min, Connected load: 132kW, Weight: approx. 85t. Including cone bending device. Documentation available. An on-site inspection is possible. Ijdpfx Ajzka H Asiysbb

Condition: good (used), Clamping plate with T-slots and cross table, plate field, welding table, welding table, plate boring mill, T-slot plate, pallet changer Ibsdpfxod Ehfme Aiyeb -Mounting plate: with a carriage with clamping device -Quantity: 1 piece (a second plate is still available ID 21154) -Wagon dimensions: 1450/810/H1120 mm -Weight: 490 kg -Width: 1465 mm -Length: 4930 mm -Working height: 850 mm -Sheet thickness: 35 mm -Plate height: 300 mm -Plate with: supporting ribs -Groove width: 52 mm -Slot spacing: 292 mm -Transport dimensions: 4930/1670/H850 mm -Weight: 5900 kg

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. Ibodpfx Aewzl Hxjiyeb * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: good (used), total length: 6,000 mm, total width: 1,650 mm, plate height: 300 mm, Manufacturer: STOLLE Type: CAST IRON... Year of construction: 2004 Specifications Metric US Standard Length 6000 mm Width 1650 mm Height 300 mm Number of T-slots 6 Distance between T-slots / spacing 250 mm Iedpfxjwpva Es Aiysbb T-slot size 27 mm Weight per plate approx. 7200 ton Number of matching pieces 4 Dimensions (estimated) Length 6000 mm Width 1650 mm Height 300 mm Weight 7200 kg Please note: The information on this page has been obtained to the best of our knowledge and, where possible, from the manufacturer. The information is provided in good faith, but the accuracy cannot be guaranteed. Accordingly, you will not be given any representation or contract terms. We recommend that you verify all important details.

Condition: new, Year of construction: 2023, functionality: fully functional, cooling capacity: 295.6 kW (401.90 HP), type of input current: three-phase, type of cooling: water, overall weight: 1,453 kg, input voltage: 400 V, total width: 1,000 mm, total length: 2,200 mm, total height: 1,880 mm, warranty duration: 12 months, Watercooled chiller PANASONIC ECOi P WQE1004CA 295.6 kW Cooling capacity: 295.6 kW / 84.05 tons (12/7 — 35°C) Year of manufacture: 2023 Refrigerant circuit: 2 pcs. Heat exchanger: Plate Compressors: 4 pcs. Bitzer GSD80295VAB4-2 (scroll) Iedpfewp Duqsx Aiyobb Type of refrigerant: R410a Dimensions: 2.2x1x1.88 m. Weight: 1453 kg. Working hours: 0/0/0/0 h. Condition: New CONDITION, TESTING & READINESS The chiller / kaltwassersatz / undergoes seven stages of technical inspection and operational parameter verification. It is also tested at our own test station, with connection to water (or glycol) and adjustment of parameters according to your requirements. After testing, you will receive a detailed report with the operating performance and the overall condition of the chiller. The chiller / kaltwassersatz / is ready for transport and commissioning. Our engineers will assist you with cooling capacity calculations, selection of the appropriate cooling scheme, and configuration of the required equipment options. WARRANTY & SUPPORT The quality of the equipment is confirmed with a warranty ranging from 6 to 36 months. LOGISTICS - Worldwide delivery available - Support with loading, export documentation, and logistics coordination Get a detailed consultation. Photos, videos, and a full testing report can be provided immediately upon request.

Condition: used, plate width 3000 mm plate depth 2000 mm plate height 230 mm Isdjud Iw Uepfx Aiyebb weight of the machine ca. / t Clamping plate Dimensions: 3000 x 2000 x 230 mm T-slot dimensions: 42 x 72 x 74 (H) The images are for illustrative purposes only. More pictures will follow.

Year of construction: 2004, condition: excellent (used), functionality: fully functional, Semi-automatic compact glass storage system 25 positions Maximum glass size: 3210 x 6000 mm Drawer load capacity: 6000 kg Total loading capacity: 150000 kg (150T) Total floor dimensions: L 6100 x W 9200 x H 3050 mm Loading width: 24 pcs. x 170 mm + 1 pc. x 410 mm. In very good and clean condition Isdszdylxepfx Aiyobb Good working order, tested As is See video

Condition: used, Technical details: Ibodpjval Nrsfx Aiyeb width:: 905 depth: 1200 mm height: 2600 mm weight of the machine ca.: ca. 4,0 / pro Winkel t Two of these clamping brackets are for sale. Material made of steel, surface finished T-slot according to DIN 650: a=22; h=36; b=39; c=17.5 mm, center distance T-slot to T-slot = 250 mm Foot clamping with 4x slotted hole Ø 21 x 30 mm There are 4 M24 holes each on the side wall (left-right) *