Turning machine - cycle control

GILDEMEISTER NEF Plus 500

Condition: good (used), Year of construction: 1999, operating hours: 42,733 h, functionality: fully functional, machine/vehicle number: 01500001111, turning length: 1,500 mm, turning diameter: 500 mm, spindle bore: 70 mm, spindle speed (max.): 2,800 rpm, spindle speed (min.): 8 rpm, overall weight: 3,200 kg, Completely overhauled by Gildemeister Bielefeld in 2010 Turning diameter: 500 mm Swing over cross slide: Ø 290 mm Turning length: 1,500 mm Spindle speed range: 8 – 2,800 rpm with three gearbox stages Spindle bore approx. Ø 70 mm Three-jaw chuck Ø 250 mm, Röhm Tailstock quill: MT4 Bdedpfx Aexx Uqrsc Nok

Condition: new, Year of construction: 2023, ENERGY T20000 20.00 KVA/16 KW At 400V 20,00 KVA /// 16 KW At 230 V 16,00 KVA /// 12,8 KW 255 KG L= 970mm W= 680mm H= 955mm Giri/min - speed 3000 Frequency Hz 50 Voltage 230/400 V Amps 32.0A at 400V 70A at 230V GASOLINE (EURO V) Electric start engine power hp (KW) 32 (23,8) Cylinder 2 Cooling system air Bedoipvhkepfx Ac Nodk Protective measures Low oil level Speed governor mechanical Fuel consumption 75% of load Lt/h 9.8 Tank capacity Lt 65 Voltage control AVR Voltage accuracy % ± 1% * 2 CEE socket 32A 3pole 230V single phase * 1 CEE socket 32A 5pole 400V three phase * 1 12V DC * Voltage selector switch (400V three-phase or 230V single-phase) * LED multimeter: Voltmeter, amperometer, KWmeter, frequency meter and hour meter. Power unit stands on 2 sturdy wheels and 2 legs, and can be moved with them. The handles can be folded to save space. Emergency gensets of the ENERGY Thunder series are not suitable for continuous operation! However, an emergency supply can be established without any problems! ENERGY T20000 Full Service Kit € 78.00 incl. 20%. * Worldwide transport incl. unloading is possible for an additional charge * An invoice with VAT will be issued

Condition: used, Year of construction: 1999, turning diameter 500 mm turning length 1500 mm control Manual Plus spindle bore diameter 70 mm turning speed range 8 - 2800 U/min transmission ratio 3 swing diameter over face slide 290 mm spindle head DIN 55027 Gr 8 tool holder Typ C quill stroke 180 mm weight of the machine ca. 3,2 t dimensions 3,0 x 1,8 x 1,8 m Description of the machine: This machine is suitable for turning chucked and shaft workpieces. The commercially available steel grades, casting, copper, aluminium, brass, gunmetal and cuttable plastic can be turned on this machine. --> Concept of the N.E.F. plus The machine si supplied as standard with the following described equipment - Cycle control - AC-Main drive - Compund slide rest with AC drive and operating panel - Tailstock traversable using slavingunit, manualy clamped, including following centre point - Coolant unti - Chip protection hoods, manually actuated - Protection hood for chuck - Fast change tool holder Hahn & Kolb Multifix C - Reduction collar for turning spindel accessories according to pictures: - 2 STK steady rests - various clamping jaws - Hahn & Kolb Multifix type C - Various torsion bar holders Technical data: Working area: - Circulation diameter over bed: 500 mm - Circumferential diameter above the radial slide: 285 mm - Chuck Ø: 250(315) mm - Face slide: 260 mm - Distance between centres: 1000/1500 mm Turning spindle: - Spindle head DIN 55027: Size 8 - Hole diameter of the spindle: 70 mm Bdedpfxoub Amle Ac Njk - Hollow taper of the spindle nose: 80 metric - Spindle diameter in front bearing

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, spindle bore: 83 mm, turning length: 1,000 mm, turning diameter: 570 mm, turning diameter over top slide: 340 mm, quill diameter: 80 mm, quill travel distance: 200 mm, overall weight: 3,200 kg, chuck outer diameter: 250 mm, Equipment: rotational speed infinitely variable, The machine is in very good condition. Immediately available! Can be tested under power. Bsdjwxw S Iopfx Ac Nedk

Condition: used, Year of construction: 2004, Technical details: turning diameter over bed: 850 mm turning dia. over face-slide: 580 mm turning length: 4000 mm centre distance: 4000 mm faceplate diameter: 800 mm control: Siemens 810D revolution per minute: 1 - 1600 / 2 step U/min max. torque on the spindle: 6000 Nm feed motor: X= plan + Z= längs: 16000 / 20000 N rapid motion - x-axis: 4 m/min rapid motion - y-axis: 7 m/min spindle passage: 130 (Spindelkopf DIN 55027 Gr. 11) mm operating hours - idle run: werden noch ausgelesen h tailstock taper ISO: MK 6 tailstock quill stroke: 350 mm max. workpiece weight between centers: 5000 kg max. workpiece weight -without tailstock: 1800 kg interface: RS 232 / V24 voltage: 400 V / 50Hz V control voltage: 24 V Gleichstrom V total power requirement: ca. 52 kW Weight approx.: 14,0 t dimension machine xH: 2,6 x 9,1 x 2,5 m Cycle lathe with Siemens cycle control Motor: 37kW, rated speed 1500 rpm; max. speed 6500 rpm; torque 235 Nm Two gear shift stages Stage II: Spindle torque 258.9 to 1364.6 Nm Stage I: Spindle torque 1050.4 - 5536.1 Nm Feed drive Three-phase servo drive 2x chip conveyor Double E-cabinet Bdedpfxju Ix Izj Ac Njk Quick-change steel holder parat Coolant device incl. various accessories see photo, as well as steady rest and 3-jaw chuck Ø 500mm Rota-S plus *

Condition: excellent (used), machine/vehicle number: 31.207.011, Manufacturing origin Swiss Voltage 380/50/3 Netweight 3150 kg Dimensions 400x185x175cm Custom position 8460 TECHNICAL DATA Distance between centres 1000 mm Centres height 175 mm Bsdpfsiwtm Sex Ac Nsdk Wheelhead Wheel : diameter/width/bore 500 / 80 (100) / 203.0 mm Max width of wheel 80(100) mm Spindle speeds 1220,1360,1530 min-1 Table maximal travel 1100 mm Table, speed (variator, progressively adjustable) 0.02 to 6.0 m/min Workpiece headstock Swivel 360° speed (variator,progressive adjust) 20 min-1 to 400 min-1 Wheelhead motor 6 HP Total power 7 HP Max diameter of workpiece 249 mm Tailstock internal taper Morse 3 errors and omissions excepted-data given without obligation

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Complete weinmann prefabricated house production line for sale. The production line consists of the following machines: - Weinmann CNC frame assembler ( WBM 150/12 ) - Weinmann multifunctional bridge ( WMS 10 ), which has 4 aggregates (end mill, circular saw and 2 staplers with Senco staplers). - Weinmann butterfly table with hydraulic lifting and panel feed ( 10m ) ( WTW 10 ) - Weinmann butterfly table with hydraulic lifting, panel feed and cross movement ( 10m ) ( WTW 10 ) - Weinmann butterfly table with hydraulic lifting and cross movement ( 10m ) (WTW 10 ), - Weinmann manually operated sorting table ( 10 m ) - roller rows between tables ( 2 + 6 pcs ) - foil support roller ( 1 pc ) Possible dimensions of wall panels: width 0.8m -3.2m, length: up to 10m, wood thickness: 8cm-24cm. The production line capacity is about 80-100 pcs 100m2 houses / year / shift. In two shifts the capacity is double this. Bdsdpfx Acjwi Rg Te Njk The production line is extremely fast, constantly maintained, well-kept, and in excellent condition. The production line includes a steel-structured wall panel warehouse, which can be dismantled and purchased separately (price not included): - 21.5 X 28 m steel-structured wall panel warehouse with 980-m rails and 300 cars. (Suitable for storing 8-10 houses) Additional information: a Hundegger K2 CNC cutting machine and a Hundegger Speed Cut CNC high-speed cutting machine, a Wolf press table (3.5-m X 30-m), as well as the entire Hungarian factory with real estate (39,000-m2 industrial site, 4,000-m2 industrial hall) with complete infrastructure are for sale at a favorable price. The factory is currently operating.

Condition: used, Year of construction: 1987, Lead and draw spindle lathe Make: Boehringer Model: DUE 560 Year of manufacture: 1987 used Technical data: turning diameter 250 mm Bdsdpstud S Uofx Ac Nok turning length approx. 1200 mm Rotation Ø over bed 560 mm Rotation Ø over facing slide 365 mm Max. workpiece between the centers 500-800 kg Spindle diameter in front bearing 100 mm Spindle bore 62 mm Spindle head DIN 55022 No. 8 Travel Face slide travel 345 mm Top slide travel 125 mm Tailstock/pinsØ 80 mm Tailstock holder MK 5 Quill stroke 190 mm Longitudinal feed 60 x 0.0315-28 mm/1 Face feeds 60 x 0.016-14 mm/1 Tapping capacity 0.125-112 mm Total power requirement 20 kW Space requirement approx. 3.5x2.0x2.2 m Weight: approx. 2.5 tons

Condition: used, Year of construction: 1968, faceplate diameter 1000 mm turning diameter over slide rest 1200 mm Bjdpfowhqzzox Ac Njdk centre distance 1500 mm bed indentation . weight of the machine ca. 6 t

Condition: good (used), Year of construction: 1990, 1 used surface grinding machine make Rosa type ER 10 year of construction 1990 Technical data Travel 1000 x 600 mm Magnetic plate 1000 x 600 mm maximum sanding height 400 mm longitudinal speed 2-30 m/min Transverse speed infinitely variable 0-3 m/min Sanding spindle speed 1450 rpm Bdjdpsuuik Sofx Ac Njk Grinding wheel diameter 400 x 60 x 127 mm Grinding wheel motor power 7.4 KW Dimensions 3900 x 20 50 x 2400 mm Weight 6 tons