Gear grinding machine Höfler Rapid 1500

HÖFLER Rapid 1500

Condition: used, Year of construction: 2017, New spindel 2025-08 yearly service by Mazak Servicecenter. includes bar feeder Super 80 Max swing Ø 658 mm Swing over X-slide Ø 658 mm Swing when Y-axis is operating Ø 658 mm Max turning diameter Ø 658 mm Max turning diameter from bar Ø 51 mm (option Ø 65) Max part length 1011mm X axis: 615mm Y axis: +/-130mm z axis: 1077mm B axis: 0,0001Deg / 240° Spindle 1 Spindle nose JIS A2-6 Spindle bore 76 mm Through-hole 51 mm (option Ø 65) Spindle motor AC 22 kW 40% ED Speed range 35-5000 rpm Number of speed ranges Direct drive Max torque 467 Nm 25% ED Max part weight including chuck 300 kg Center height from floor 1235 mm Spindle 2 Ncjdpfxex Hfl Eo Adwol Spindle nose JIS A2-6 Spindle bore 76 mm Through-hole Not applicable (option Ø 65) Spindle motor AC 18.5 kW 40% ED Speed range 33-5000 rpm Number of speed ranges Direct drive Max torque 325 Nm 40% ED Max part weight including chuck 300 kg Center height from floor 1235 mm C-axis 1 Type Direct drive Rapid feed 555 rpm Working feed 1-5000 degrees/min Minimum programmable increment 0.0001 degree C-axis 2 Type Direct drive Rapid feed 555 rpm Working feed 1-5000 degrees/min Minimum programmable increment 0.0001 degree W-axis Movement 1066 Rapid feed 30 m/min B-axis B-movement 240 degrees Max machining feed (ISO) 40 rpm Minimum programmable increment 0.0001 degree Tool Holder Type: Tool changer Tool Shank Size: 25 x 25 mm Tool Change Time, tool to tool: 1.3 seconds Chip-to-chip time, average: 8 seconds Tool Holder for rotating tools: Capto C6 Tool Holder for turning tools: Capto C6 Max Tool Weight: 12 kg Max Tool Length: 400 mm Clamping Force for Tool (Capto C6): 33 kN Tool Magazine: Number of tool positions: 36 pcs Max Tool Diameter: 90 mm Max Tool Diameter when the position before and after is empty: 125 mm Max Tool Length: 400 mm Max Tool Weight: 12 kg Max Torque for Tool: 9.8 Nm Other: Length: 3990/4910 mm Width: 2800 mm Height: 2720 mm Weight: 13100/16600 kg Power Requirement, continuous: 72.34 kVA Air Requirement, min: 5 kg/cm², 410 liters/min Tool Magazine: 36 tools Standard Equipment: B-axis Capto C6 ATC Auto Recovery Auto power on/off, heating schedule 19” LCD touchscreen Mazak tool identification system including 10 ID chips (for Capto C6) Measurement arm for tool length setting, automatic compensation, and tool breakage detection 8” Chuck Type: Kitagawa B208A6 8” Chuck Type: Kitagawa B208A6 Coolant Tank Coolant Pressure for Upper Turret: Max 5 bar, 23 l/min Set of Manuals: (digital) Smooth Standard Software: Mazacc 2D software (shape comp) Mazacc 2D software för roterande axlar (shape comp) Mazacc 3D High Speed software High Smoothing Control Seamless Corner Control Variable Acceleration Control Ultra High Speed Machining Mode Rapid Overlap ISO/EIA Programming: Lathe and milling spindle start unsynchronized Synchronized threading with rotating tools Macro interruption allowing event-driven ISO/EIA programs Macro programming with 600 additional variable pairs for ISO/EIA Helix interpolation for ISO/EIA Coordinate rotation with G68 for ISO/EIA Polar coordinates, G122 for ISO/EIA Synchronized interpolation X-C-axis G12.1 for ISO/EIA Coordinate systems G54 - G59 + 300 additional for ISO/EIA Direct input of drawing dimensions, e.g. starting corner for ISO/EIA Inverse Time Feed (G93) 3D Cutter Compensation (G40-G42)

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, Initial commissioning: 2000 Control system: Heidenhain TNC 430 M Machine hours: 111,500 h X-axis: approx. 4,000 mm Y-axis: approx. 2,360 mm Z-axis: approx. 1,250 mm A-axis: ±110° C-axis: ±300° Clamping table Clamping surface: approx. 6,000 x 2,000 x 420 mm T-slot spacing: 18H12 / 250 mm Max. table load: 30,000 kg/m² 2-axis milling head AC3 Spindle power: 25 kW Spindle speed: max. 15,000 rpm Torque: 80 Nm Tool holder: HSK 63A Tool clamping: hydraulic Spindle freshly overhauled at the end of 2024! Linear axis drives Feed rate X, Y axis: up to 20 m/min Feed rate Z axis: up to 20 m/min Axis acceleration X, Y, Z: up to 1.5 m/s² Connection data Nedpfxow Rl S Ss Adwecl Connected load: 40 kW Main fuse: approx. 80 A Dimensions & weights Machine footprint with peripherals: approx. 8,500 x 5,600 x 4,945 mm Total weight: approx. 18,000 kg Colour Enclosure, gantry, control cabinet: light grey Milling head and applications: green Additional equipment - 3-sided enclosure, without extraction ducts - The additional clamping table shown is not included in the scope of supply Condition of the machine Fully functional, in very good condition. Machine remains connected and is available immediately.

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: GS1000/5-T, rotational speed (max.): 30,000 rpm, overall weight: 15,500 kg, Year of manufacture: 2014 Nodpfxsw Awmte Adwocl Condition: very good Magazine: 66 x HSK63 Control: Heidenhain 530 Spindle: n=30,000 Erowa zero-point clamping system integrated into the table Erowa Robot Easy 250 automation with 6 pallets 3D probing system Oil-air lubrication of high-frequency spindle Laser measurement Spindle hours:

Condition: like new (used), Year of construction: 2021, functionality: fully functional, Double spindle CNC lathe with 2 spindles, 3 turrets and 3 Y axes Ncjdpfsvxu Eajx Adwol each turret with 15 stations, BMT 44 driven tool holder 2x C-axis 3x Y axis Fanuc 32i -TB control Bar passage 65 mm Left spindle 15/11 KW, Hainbuch Spanntop mini Axle pull size 65 Right spindle 11/7.5 KW, Kitagawa three-jaw chuck Finished part gripper Conveyor belt Bar loader interface Coolant system, separate tank 200 l Cooling unit High pressure on turrets 1-3 via M function 15 bar/40 l/min 2x Brinkmann pump Renishaw tool measurement for all turrets Tool monitoring for spindle and AGW Spindle flushing through the counter spindle IKZ, Deublin Rotary distributor Hinged belt conveyor Transformer available immediately

Condition: used, Year of construction: 2007, max. wheel diameter 500 mm Hypoid adjustment ±70 mm axial cross angle 90 ° Distance Y- 150 - 350 mm Distance Z-axis 120 - 340 mm turning speed range - stepless 0 - 5000 U/min max. torque on the spindle 57 Nm Cone 99,2 mm Pull-in force Tool clamping 23000 N Braking torque max. 93 Nm total connected load 20 kVA total power requirement 15 kW Ncodpfsukitxsx Adwjl weight of the machine ca. 6 t dimensions of the machine ca. 2,35 x 2,24 x 2,5 m

Year of construction: 1990, condition: good (used), machine/vehicle number: 92041, table mounting size: 410 x 900 mm movements x/y/z: 560/410/380 mm spindle taper: SK 40 spindle turning speed range: 22 - 6000 rpm carriages: x/z until 10000, y until 240 mm/min Ncjdpfxjdhhpro Adwel space needed: 2600 x 2000 x 2300 mm weight: 3500 kg

Year of construction: 2015, condition: ready for operation (used), A CNC double-spindle lathe Traub overhauled in 2025 is available. Turning length: 450mm, spindle clearance: 65mm, speed: 4000rpm, main spindle/counter spindle power: 18.5kW/11kW, tool positions: 10, driven tools: 10, hydraulic capacity: 150l, hydraulic pressure: 60bar, connected load: 39kW. Rapid traverse X1/X2: 15m/min, feed force: 5000N, feed path: 140mm. Rapid traverse Z1/Z2: 30m/min, feed force: 8000N, feed path: 450mm. Rapid traverse Y1: 6m/min, feed force: 8000N, feed path: +/-35mm. Machine dimensions X/Y/Z: approx. 4150mm/2000mm/1800mm, weight: approx. 4750kg, control: Traub System TX 8F, operating hours: 12938h. Including chip conveyor and bar loader LNS Quick Load. Documentation available. On-site inspection is possible. Nodpfjv Scrbsx Adwjcl

Condition: used, Year of construction: 2008, Swing over bed 923,8 mm Swing over cross slide 755 mm Max. turning diameter 356 mm Ncodpfeu Sn Hzox Adwol Max. turning length 510 mm X/Z-axis movement 260/590 mm Turret w/12 stations Spindle speeds 5000 rpm Spindle bore 73 mm Control: MSX-850 III Equipped with: Collet chuck w/collets Chip conveyor 3 standard tool holders No Gantry loader incl.

Condition: good (used), Year of construction: 2004, Clampable cutter head type (max.) 460 mm Ncsdsul Efmjpfx Adwol Cutter head weight (max.) 150 kg Mounting disc diameter for cutter heads (Ø) 360 mm Mounting cone for cutter heads Nominal diameter Ø 58,227 mm travel -z axis 200 mm diagram-drawing enlargement ±10 - ± 500 µm weight of the machine ca. 2,3 t dimensions of the machine ca. 2 x 1,5 x 2,03 m In the manufacturing process for spiral-toothed bevel gears, the quality of the gear cutting gear cutting tools used plays a decisive role. Particularly in high gear cutting quality and a long service life can only be achieved with precisely can only be achieved with precisely adjusted cutterheads. The Oerlikon cutterhead setting and testing device CS 200 enables quick and easy setting of the individual knives and simple adjustment of the individual knives, it checks the position and documents the measurement results. The measuring sequence on the CNC-controlled testing device is partially automated: The individual actions for carrying out the actions for carrying out the sequence are displayed on the screen via the operator guidance. The positioning of the individual knives in the cutter head and the height of the knife tips is largely automatic thanks to a special sequence and is simultaneously documented by means of a run-out diagram. A subsequent measuring sequence checks the radial position of the inner and outer cutting edges of all knives in the cutterhead. If individual test parameters on the knives do not correspond to the the tolerance specifications, this can be individually repositioned. The combination of semi-automated setting sequence, operator-guided set-up actions and automatic operator-guided set-up actions and automatic measuring sequence, cutterheads can be can be set conveniently, quickly and with high precision. Operator-guided setting and test sequence - Graphic display of the cutter head design and the measurement results with tolerance check - Instructions for the operator in plain text Instructions for the operator in plain text (without coded information) - Simple assignment of the measurement results to the knives - Documentation of the setting and measurement results via printer- Setting and test sequence suitable for ARCON®, RSR, Spirapid, SPIRON®, TRI-AC® types - Interface for neutral data

Condition: like new (used), turning diameter: 1,500 mm, MAXIMUM WORK DIAMETER : 1600 mm. MAXIMUM WORKING LENGTH : 3000 mm. DIAMETER OF LANTERN SHAFT : 83 mm. OUR MACHINE IS ACTIVE WITHOUT ANY PROBLEMS Ncjdpfx Ader Ui R Njwel ALL REVOLUTIONS AND AUTOMATICS ARE IN VERY GOOD CONDITION