Four Column Press - Hydraulic

Hidrobrasil Viersäulenpresse

Condition: as good as new (ex-display), Year of construction: 2020, pressing force: 400 t, Hydraulic 400 to column press suitable for continuous shift operation, with these basic data: a) Closing speed 100 - 450 mm/sec. b) Opening speed 50 - 250 mm/sec ( adjustable via touch screen ) c) Pressing speed 5 - 60 mm/sec ( adjustable via touch screen ) d) Piston accumulator with approx. 4 nitrogen bottles e) Table size (clamping surface) 2700 x 1700mm ( seen from the front, between the columns ) f) Total table size 3400 x 1700mm g) 28 T-slots according to customer requirements h) Table, ram and press head are annealed stress-free. i) column diameter 250 mm j) slide size 3400 x 1700mm (clamping surface 2700 x 1700mm ) k) Total size of the machine approx. 3900 x 2200 ( at the bottom ) x 5700 mm height l) Oil temperature monitoring ( adjustable via touch screen ) m) Automatic lubrication ( adjustable via touch screen ) n) Free positioning of the ram ( adjustable via touch screen ) o) KEYENCE light barriers 14 mm on front and rear side p) Circuit oil cooling ( adjustable via touch screen ) q) Pressure holding valve 0 to 600 sec. ( adjustable via touch screen ) r) Table top size 3400 x 1700mm, plane milled s) Laterally monitored doors, 1200mm high, 1000mm wide Dcjdpfx Aleg Iihws Ajk t) RITTAL control cabinet, 2200 mm wide, up to 20 m from the press u) Pressure setting from 50 to 400 tons ( adjustable via touch screen ) v) Travel limitation optionally via pressure or position w) Programming mode, set-up mode, single stroke + continuous stroke (adjustable via rotary switch ) x) Swivelling control panel with 15 inch touch screen monitor y) Two-hand operation on both sides z) Prepared for automatic material feed ( SIEMENS S 7 1500 ) aa) Machine body primed and painted bb) assembly, commissioning, instruction against separate charge The hydraulics of the presses we offer are completely based on BOSCH-REXROTH/Parker/HAWE components. In the switch cabinet only components are used (SIEMENS) which are easily available in Germany. The safety technology comes completely from SICK except for the light barriers. The control system is supplied by SIEMENS. ( S 7 1500 ) as well as the touch screen monitor with 15 inch. The SIEMENS remote maintenance unit SECOME -Ethernet is included in the scope of delivery. SPECIAL FEATURE: the design chosen by us with two press cylinders and the piston accumulator make it possible to supply the full power with a main motor of 90 kW. Below under 1.3 the technical details Technical data Press design Press design Column press Thermally neutral 80 - 120 °C Number of operating sides 2 sides Forces Pressing force max. 4,000 kN Free ripping force max. 600 kN Pressure build-up time Closed tool steel to steel Max. 2 sec. Dimensions - intended minimum tool height 600 mm Max. Opening width 1600 mm Stroke and min. opening 1000/600 mm Table height above floor 820 mm Height above floor (headroom) approx. 5700 mm Hall height min. 7000 mm Parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.17 mm/m Weight Total weight of the press without operating materials approx. 52 To Speeds ( see attached cycle diagram ) Fast closing 100 - 450 mm/s Pressing speed At F max.

Condition: used, Year of construction: 2011, Technical details: Djdpfx Aljw S Efzj Aock turning length: 310 mm swing diameter over bed: 500 mm swing diameter over bed slide: 290 mm centre distance: 500 mm x-axis: 190 mm z-axis: z1: 335 / z3: 370 mm y-axis: 80 mm revolution per minute: 6000 U/min Control: Heidenhain CNC Pilot 4290 spindle bore: 73 mm bar material dia.: 50 mm tool turret - number of stations: 12 tool taper: VDI 30 mm rapid traverse x + z axis: 30 m/min operating hours - idle run: 36443 h spindle hours: 8545 h interface: ja total power requirement: 20 kVA kW dimension swarf conveyor LxWxH: 3,2 x 0,45 x 1,5 CNC inclined bed lathe With a 3-jaw chuck Ø 160mm with matching flange (max. speed 4500 rpm) and 2 additional sets of spare jaws. Turret head for 12 tools all with tool drive; Sauter disk turret (C-axis = 300 rpm) Torque main spindle: 95 Nm at 100% and 127 Nm at 40% Chip conveyor 450 K-1/250; year of manufacture 2000 Electric cabinet with Rittal cooling The machine does not have a hydraulic chuck. A manual chuck has been installed by the previous owner. The machine is not functional and is for sale. The machine has an unknown malfunction in the turret, meaning that reference travel and axis movements are not possible. Machining functionality is therefore currently not possible. The machine is for sale and in need of repair! i.D. *

Condition: new, Year of construction: 2019, machine/vehicle number: DF0329, pressing force: 350 t, pressure:350 t passage width:3000 mm stroke:900 mm total power requirement:75 kW weight of the machine ca.:60 t Dcsdpfofxygzsx Al Ask dimensions:2660 x 5400 x 5700 mm return capacity:35 t Table dimensions:3610 x 1600 mm :3610 x 1600 mm table height over floor:900 mm pre-running speed:230 mm/sec return speed:170 mm/sec :2000 l max. working heidht:1700 mm pressure speed:21 mm/sec speed rapid traverse:200 mm/sec Oil cooling (electric):3 kW (max) :S7 1500 Monitor:WEG 12 Zoll

Condition: new, machine/vehicle number: DF0279, pressing force: 1,000 t, pressure:1000 t passage width:1500 mm stroke:800 mm Djdpfjfxyiyex Al Asck total power requirement:91 kW weight of the machine ca.:68 t dimensions:3850 x 2900 x 6000 mm return capacity:100 t Table dimensions:1500 x 2250 mm :1500 x 2250 mm table height over floor:1300 mm pre-running speed:200 mm/sec return speed:200 mm/sec Pressure Speed:10 mm/sec :1200 l Oil cooling (electric):1,5 kW (max) Max Working height:1000 mm :200 mm/sec Monitor:12 Zoll

Condition: like new (used), Manufacturer: Varian Type: NHS-35 Condition: The pump is in very good condition and can also be supplied with a corner valve if required. Warranty: 3 months Dcodohmba Aepfx Al Aek Delivery time: In stock

Condition: used, Year of construction: 2019, pressing force: 250 t, pressure:250 t passage width:2500 mm stroke:500 mm total power requirement:60 kW weight of the machine ca.:39 t dimensions:2720 x 3750 x 4350 mm return capacity:25 t max. working heidht:800 mm Table dimensions:3090 x 1500 mm :3090 x 1500 mm table height over floor:1000 mm pre-running speed:400 mm/sec pressure speed:bei 125 t, 50 mm/sec Return Speed:400 mm/sec speed rapid traverse:400 mm/sec Dcsdpfx Alod Nq Ide Aok :1500 l Oil cooling (electric):3 kW (max) Vibration damper plates:je 450x450x85 mm pressure:250 t bei 220 bar t/bar pump capacity:176 Lt./min :46er / 10 my Hydraulics from Bosch Rexroth or other German manufacturers :Parker, Hydac :inklusive Light Barriers from Schmersal/Pilz:Pilz Monitor:Omron 12 Zoll

Condition: new, pressing force: 100 t, pressure:100 t passage width:700 mm stroke:450 mm weight of the machine ca.:6 t dimensions:ca. 3000 x 1210 x 3100 mm return capacity:10 t :22 kW Max Working height:850 mm :1 - 100 mm speed of return flow:1 - 100 mm/sec :1 - 10 mm/sec. pestle plate:1090 x 600 mm table plate:1090 x 600 mm positioning accuracy:0,1 mm table height over floor:800 mm :300 l Oil cooling (electric):1,5 kW (max) ejector:d=100 mm ejector stroke:210 mm pressure of ejector:100 t no. of ejector pins:1 Stück Monitor WEG:15 Zoll :2.000,-- ? :2.400,-- ? :3.000,-- ? Dedpfx Alefxyhqs Asck :2.400,-- ? :5.800,-- ?

Condition: used, material width 300 mm coil weight 3 t material thickness 2 - 4 mm Straightener, 7 rolls, Make. Schleicher, Type RM 6-95/160 - band width 300 mm - band thickness 2 – 4 mm - cross cut 1200 mm² - voltage 220/380 V 50 Hz - total power requirement 3,1 kW coiler with press roll, Make Schleicher, Type H-3 - Coil weight 3 t - Band width 400 mm - voltage 220/380 V 50 Hz - total power requirement 3,92 kW without control Dodecdrmmspfx Al Asck

Condition: new, Year of construction: 2019, machine/vehicle number: DF0362, pressing force: 250 t, pressure:250 t passage width:1800 mm stroke:600 mm total power requirement:22 kW weight of the machine ca.:24 t dimensions:ca. 3390 x 3400 x 3800 mm column diameter:160 mm return capacity:25 t max. working heidht:800 mm Dcsdofxyinopfx Al Aek Table dimensions:1800 x 1600 mm :2350 x 1600 mm table height over floor:900 mm hydraulic table shift:25 mm/sec table load:5 t pre-running speed:10 mm/sec pressure speed:10 Return Speed:25 mm/sec speed rapid traverse:10 mm/sec :600 l Oil cooling (electric):1,5 kW (max) :46er / 10 my Monitor SIEMENS:10 Zoll

Condition: excellent (used), MAZAK INTEGREX 400-3S is a CNC Turning-Milling-Drilling Center designed for precision, high accuracy and reliability. Capacities: distance between centres 1500 mm, swing 760 mm, max turning length 1524 mm, bar passage 102/77 mm, tool magazine 40 stations (Ø max 90 mm, L 400 mm). Main specs: main spindle A2-8 stepless 35–3300 t/min 30 kW 1200 Nm; back spindle A2-8 35–4000 t/min 26/22 kW 500 Nm; milling spindle CAPTO C6 15–12000 t/min 18.5 kW 120 Nm. Travels X630 Y±115 Z1585 mm; feeds 0–8000 mm/min; rapid X/Z 38 m/min Y26 m/min; weight ~13300 kg; footprint 5110x2196 mm; height 2798 mm. Equipment: coolant 444 l (15 bar through milling spindle), Forkhardt 3-jaw chucks Ø400/315 mm, linear scale for X, RS232, PCMCIA, spindle sync, chip conveyor, synchronized tapping, foot pedal. Enables tight tolerances; typical applications: automotive, aerospace, medical, machine tools, watchmaking. Djdpfx Aoyxn H Nel Ajck