CIP plant

Holstein und Kappert

Condition: used, Year of construction: 2010, PARAMIX unit for carbonated drinks. The included process steps are: Deaeration of water, dosing and mixing of water and syrup, carbonating of water-syrup blend. Retrofit 2009 by FAMIX: - Carbonating device - CO2 pressure-temperature ratio controller Type BMS7 The controller including control cabinet is to be completely renewed when the machine is purchased. Additional title: mixing unit 1983 - 2010 Capacity approx.: 150 hl/h Mixing and carbonating Length: 2,9 m Dodpexbn Hrofx Anqoci Width: 2,5 m Height: 2,5 m Weight: 3000 kg Operation / Control: mixing unit semi automatic, carbonating unit automatic Siemens S7 Material: Stainless steel Position: Frame mounted Features: 2 pressure vessels (Product und Vacum), each 8,3 hl/ 8 bar, CO2-Pressure-Temperature regulator (FAMIX BMS7), Carbonising unit (FAMIX) Capacity 13000 l/h, PT 100, Pressure sensor, Pressure relief valve, CIP connection, control cabinet, HMI (Siemens), 2 mixing vessels with flap and agitator (Ahlborn, approx. 15 hl per vessel)

Year of construction: 2018, condition: ready for operation (used), Two identical Göztepe belt fryers are available for vegetables (onions, potatoes, nuts, etc.). Working length: 6800mm, working width: 700mm, inlet height: 1280mm, outlet height: 1060mm, working temperature: 180°C, plastic belt length and width bottom: 14000mm/720mm, plastic belt length and width top: 8500mm/720mm. Machine dimensions X/Y/Z: approx. 6900mm/1800mm/3500mm, total output: 135kW. Documentation available. On-site inspection is possible. Dcodpfx Anou Tiy Njqsi

Year of construction: 2023, condition: ready for operation (used), A new belt roasting machine for nuts in the food industry is available. Fuel: diesel/electricity/gas/LPG, output: 2kW, machine dimensions X/Y/Z: approx. 3600mm/1900mm/1950mm, operating hours: 31h. Roasting capacity per hour: hazelnut kernels: 160kg, shelled peanuts: 150kg, shelled peanuts: 35kg, shelled pistachios: 90kg, sunflower seeds: 70kg, pumpkin seeds: 70kg, almonds: 120kg, cashew nuts: 150kg, chickpeas: 120kg. Including salt kettle with a capacity of 35kg and fully automatic high-pressure belt washer. Documentation available. On-site inspection is possible. Dcodpfxeu Ei Utj Anqoi

Year of construction: 2026, condition: new, Continuous pasteurizer electric - up to 400 ltr./h * Water bath boiler * Electric heating 13.5 / 18 / 27 / 31.5 kW - 400 V Dedpfx Aet Uzitjnqoci * Container (stainless steel) 150 ltr. with thermal insulation * Stainless steel tubular heat exchanger * Automatic low temperature safety device (compressed air required) * Stainless steel juice pump * Chassis with holder for low temperature safety device and pump ##### RINK - Pasteurizers for more than 30 years Proven technology - more than 500 units in customer use

Condition: used, Year of construction: 2013, Overview The Heuft InLine IR – high speed empty bottle inspector is characterized by its compact installation dimensions. High-speed inspection of empty bottles is easily possible (up to 50,000 bottles/h). It can perform all standard inspections (sidewall inspection, infeed inspection, neck finish inspection, base inspection, discharge inspection, HF caustic and IR residual liquid detection). In addition, it has a separate module for foreign bottle detection (height, contour, color). In 2016 it was overhauled and modified installed including conveyor control. Tech Specs: - Capacity: 5,000 – 50,000 bottles / h - Compact installation dimensions - 2016 overhauled and modified Features: Djdjukafrspfx Anqeci - Processes all standard inspections: sidewall, infeed, neck finish, bottom, discharge, HF caustic and IR residual liquid detection - Separate module for foreign bottle detection (height, contour, color)

Condition: new, Year of construction: 2024, functionality: fully functional, nominal power: 90 kW (122.37 HP), rotational speed (max.): 5,760 rpm, rotational speed (min.): 1,592 rpm, total height: 3,437 mm, total length: 3,275 mm, total width: 2,500 mm, type of cooling: air, compressed air connection: 6 bar, Equipment: rotational speed infinitely variable, The impact mills of the REKORD 212-630 series in the welded housing design are robust universal mills for demanding industrial applications in continuous operation. ● Size: 630 mm (nominal rotor diameter) ● Mill housing: Heavy-duty welded stainless steel housing, pressure surge resistant up to 10 bar (AISI316L), with product-contacting surface finish Ra ≤ 1.6 μm for easy cleaning, equipped with a pivoting door and safety interlock type HAAKE (key transfer system); monitoring of housing and bearing temperature, vibration monitoring ● Mill inlet: JACOB pipe; DN 150 mm ● Mill outlet: Ground material and air discharge downward into a suction hopper, optimized for connection to the conveying line to the total separator ● Mill drive: Belt drive, three-phase motor, energy efficiency class IE3 (manufacturer SIEMENS), 90 kW, 3~ 400 V, IP55; suitable for operation with frequency inverter ● Sealing materials: Silicone; PTFE, sealing material conforms to EU and FDA food hygiene standards ● Grinding elements: Pin rotor: 4 pin rows, pin Ø 7 mm (wear-reduced); Pin stator: 3 pin rows without external pin circle, pin Ø 7 mm ● Bearings: Designed for toughest operational demands in continuous industrial service, heavy-duty bearing housings with temperature and vibration monitoring (early detection of potential bearing failure and avoidance of hot surfaces) ● Inert gas supply/monitoring for shaft seal on product chamber side ● Run monitoring to detect operating faults ● Machine frame: The complete unit – mill, drive with motor, tensioning rails, belt drive, and belt guard – is installed ready for use on a sturdy machine frame with height-adjustable machine feet Main components of the offered system include: ● Product feed/transfer from customer’s upstream process and transfer to a rotary valve (certified ATEX protection system); ● Industrial pin mill type REKORD 630-SSt with welded housing and ground surfaces; Djdpfjx Ac Rbsx Anqeci ● Product separator with discharge rotary valve (certified ATEX protection system); ● Pneumatic conveying line with air inlet/outlet, including suction blower; ● WITHOUT control system, without frequency inverter

Condition: good (used), Semi-automatic can seamer for rectangular cans, in good condition. Dodpfx Anjxupygjqjci

Condition: used, Glass bottle filling line consisting of the following components: 1. Bottle washing machine (separate unit, Silmo, 1982) with a nominal capacity of 2,880 bottles/hour 2. Rinsing, filling, capping and labelling line (IC Filling Systems, 2020) with: - Bottle feed table - Rinser - Counterpressure filler - Capping machine - Bottle exterior washer - Cold glue labelling machine - Bottle discharge table - Free bottle transport Capacity appr.: 1100 bo/h referring to 0,33 l bottles Dsdpfx Ajw Ta Ndjnqsci Length: appr. 7 m Width: appr. 4 m Formats: Euro 0.5 l and 0.33 l; crown caps; wrap-around labels and belly labels Running direction: clockwise Base construction: Rinser, filler and capper as a monobloc Features: Bottle cleaning machine, bottle feeding table, rinser, filler, capper, bottle exterior washer, labeller, bottle discharge table, beer pump

Condition: new, Year of construction: 2026, Dispensing ranges: 1 ml - 38 ml 2 ml – 100 ml Dcsdpfjwpr Tbsx Anqji 5 ml – 250 ml 20 ml – 680 ml 50 ml – 1,500 ml Bottle feed via a bottle sorting system or a stainless steel turntable Volumetric filling Underlevel filling possible Adjustable filling nozzles Pumps and filling nozzles made of stainless steel AISI 316 L Multi-format stars for different bottle diameters Automatic or manual cap application Stepless torque adjustment of the capping Capping system for plastic caps and optionally for aluminum caps Bottle transport via slat chain conveyor (3,000 mm, depending on order) Display control Labelling is optionally possible Built in Rhineland-Palatinate / Germany

Condition: used, Water or liquid filling line for PET containers – capacity approx. 6000 bph (2.0 L) Currently, the machines are configured for 2.0 L PET bottle formats (other formats not included). It is possible to adjust to smaller or larger PET bottles by preparing the appropriate equipment. The line includes: - Nagema BF-60 filler with 12-head bottle capping unit - Plate conveyors for PET bottles - Nagema saturator, type KOMI 160 - Spomasz wrap-around paper labeller - Bottle packer with control cabinet for creating multipacks, e.g. 2x3 - Electric shrink oven + cooling fan for multipacks Dcjdpfx Anewny Hgoqsi - Pallet wrapper The last photo shows the layout and dimensions of the machines. Technical condition: the machines were operational up to the end of production in 2018. Inspection and maintenance are recommended before resuming production. Optionally, a SIDEL SBO4 blower, which was last in operation on this line, can also be purchased.