Band saw

IMET AFI-E / BS350

Condition: ready for operation (used), Year of construction: 1998, cutting diameter 305 mm capacity 90 degrees: flat 350 x 200 mm capacity 45 degrees: round 250 mm capacity 45 degrees: flat 230 x 200 mm capacity 60 degrees: round 175 mm capacity 60 degrees: flat 170 x 100 mm cutting speed 18 - 110 m/min vice max. 350 mm dimensions of saw-band 3370 x 27 x 0.9 mm Guedpfxeyy A Hyj Aa Sea engine output 1.5 / 1.8 kW weight of the machine ca. 880 kg range L-W-H 1700 x 2200 x 2000 mm Equipment: - robust, electro-hydraulic fully automatic band saw - user-friendly controls - Mitre cuts left to 45 . possible in automatic mode - Mitre cuts up to 60° . only possible in semi-automatic mode - Hydraulic power unit with automatic . pressure cut-off when idling - Stationary base frame * with large chip drawer and automatic cooling system - infinitely variable saw blade speed adjustment (ESC) - rotating chip brush - remnant min. 80 mm - operating instructions (PDF)

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: Gujdehzbipjpfx Aa Ssa - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: new, Straightening press 150 tons with electric motor and additional manual operation by a hand lever pump, especially for fine work. Versions: 30t 60t 100t 150t 200t ᐳ 200 t: on request Special machines: on request Godpfx Aaof Sqcko Seua New machine! We are also happy to build a customer-specific press for you. High quality hydraulic workshop press with 150 tons maximum pressing force. The press can also be opened and closed in the classic electric mode using a lever. For fine work (e.g. pressing in bearings, straightening, ...) the press also has a hand pump. This allows you to fine-tune the force manually. The printing cylinder is attached to a sliding carriage so that the cylinder can be moved sideways. In this way, you can make optimal use of the maximum stand passage width. Particularities: - 150 tons maximum pressing force - Pressure display with manometer - 2 operating modes: electrical operation or or manual operation - 2 independent hydraulic pumps - Control cabinet with motor protection monitoring and safety devices - adjustable passage height - Pull chains for easy adjustment of the passage height - massive machine frame - cylinder laterally adjustable (mounted on sliding carriage) The press can be tested under power on site. ----- Numerous other workshop presses in different designs, sizes and with optional additional equipment available! 30, 60, 100, 150, 180, 200 tons. ----- Please just contact us, we will be happy to advise you without obligation. The stated price is net plus 19% VAT. All statements without guarantee! Europe-wide delivery possible! ----- The European Commission provides a platform for out-of-court online dispute resolution (OS platform). The offer serves exclusively as an internet presentation of our goods. The contract negotiation comes about by means of telecommunication (email, fax, telephone, news portal), where we first make you a non-binding offer, in which we inform you about our general terms and conditions and the right of withdrawal with imprint before the purchase / contract is concluded.

Condition: good (used), Year of construction: 2019, machine/vehicle number: 24451.19, Offer 25359 Technical Data: - Cutting capacity at 90° (round): 250 mm - Cutting capacity at 90° (flat): 275 x 180 mm - Miter adjustment to the left - Cutting capacity at 45° (round): 200 mm - Cutting capacity at 45° (flat): 190 x 180 mm - Cutting capacity at 30° (flat): 130 x 110 mm - Material support height: approx. 920 mm - Saw band dimensions: 3100 x 27 x 0.9 mm - Infinitely variable cutting speed: 15 to 100 m/min - Hydraulic lifting and lowering of the saw frame Gujdjxup Rfspfx Aa Sja - Upper travel limit of the saw frame - Infinitely adjustable cutting pressure: 0 – 10 m/min - Hydraulic material vice - Micro-spray cooling system - Total drive power: 400 V / 2.2 kW - Required space approx.: W 2400 x H 1600 x D 1800 mm - Weight approx.: 1300 kg - 3 x Roller conveyor, each 1500 mm

Year of construction: 2007, condition: good (used), Danobat CNC Drilling / Sawing Line – Year 2007 Single Rotating Spindle. 18 metres In- Feed Rollers. 12 metres Out- Feed Rollers. Pincher Unit Feed. Infeed Cross Transfers. Outfeed Cross Transfers. 750mm Capacity. Sawing Capacity: Round cutting capacity(without vertical jaws, angle 0 degrees) 520 mm. Rectangular cutting capacity (without vertical jaw, angle 0 degrees) 700mm X 500 mm. Maximum capacity with vertical jaws 700 X 500 mm. Gsdpfx Asig T Amoa Ssua Round cut capacity with 45 degree turn, 450 mm. Rectangular cutting capacity with 45 degree turn, 450 X 500 mm.

Condition: new, Year of construction: 2025, All-round fiber laser metal tube cutting machine Multiple function options help the laser tube cutting machine be used in numerous tube cutting processes. The slender nozzle allows the laser tuber cutter to avoid interference and cut various types of tubes, including special-shaped tubes like H-Beam, P-Beam, I-beam, etc. Cutting machine clamping becomes convenient, easy and fast, with 3 seconds at the soonest to clamp and high repeat precision Cutting performance and efficiency are improved by maintaining gas flow steady with little turbulence. BodorGenius, combined with the lightning-quick piercing process, completes the whole piercing during it moves down on Z-axis. Thanks to the technology, no reworking is necessary for medium and thick sheet piercing. Angle steel and channel steel cutting are standard with no need for additional installation. Gusdpohwrk Tofx Aa Sea Optimized edge searching method and algorithm guarantee higher cutting precision and better steadiness of the laser cutter. Condition: New Laser Type: Fiber Laser Laser Power: 1500W, 2000W, 3000W, 6000W Maximum machinable tube length: 6500mm/9200mm Chuck drive types: NC electric chuck Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Year of construction: 1997, condition: used, machine/vehicle number: 540897, pipe diameter max. 1,500 mm tool diameter max. 200 mm feed rate 40 mm / min sawing of pipes in steel and greycast iron  with wall thickness of up to 22 mm  milling of pipes in steel and grey cast iron with wall thickness of up to 15 mm Guodeghy Azepfx Aa Sea cutting speed 35 m / min compressed air requirement 6 bar - 2m³ / min weight approx. 90 kg

Condition: new, Year of construction: 2026, Robotic gantry system for metal sheet and profile cutting 3D robotic gantry system for plasma and oxy-fuel cutting has double-side drive, precise positioning system by racks and pinions on the 3 linear axes with exceptional speed and dynamics. Zero-backlash on the 3 rotational axes allow 4-side machine processing of profiles and round tubes. Precise gearboxes with minimum backlash, dynamical engagement of the motors to the racks, and rigid guide system allows smooth movement, excellent cut quality of corners and small holes. The gantry system has a cantilevered part crossbeam, which allows profile cutting in a cabin especially designed for this purpose. Transversal motion range (Y axis) -- on request Longitudinal motion range (X axis) -- on request Vertical motion range (Z axis) -- 1500 mm Beams and profiles types: T, L, H, U, rectangular tube, round tube Maximum dimensions of beams: Godpfx Aaeh I Nw Dj Sjua Width up to 1200mm Rectangular tubes: Cross-section up to 600x600mm KEY FEATURES ▪ Stable metal construction with precise linear guides and servo-drives with racks and pinions on all axes; ▪ High dynamics, on all X, Y and Z axes: up to 30 m / min speed and acceleration up to 3 m / s²; ▪ 3D control on seven axes allows for a higher level of CNC programming; ▪ Maximum use of machine resources, thanks to the concept of combined processing of sheets and profiles - the ability to 100% load the machine when switching between sheets and profiles, without downtime for loading sheets and profiles and unloading cut parts ▲ PLASMA CUTTING EQUIPMENT HYPERTHERM -- on request ▲ INSTALLATION AND TRAINING INCLUDED Approximate installation and training period - 15 days

Year of construction: 2000, condition: excellent (used), Kaltenbach / APS CNC Flat Bar / Angle Punching / Shearing Line – Year 2000. 500mm Capacity Flat Bar. 60mm x 160mm Angle. 3 head Punch. Horizontal punch. 12 metres Gripper feed. Mitre Shearing. Guodeirakrepfx Aa Soa

Year of construction: 1994, condition: good (used), machine/vehicle number: S 2645, Offer 22347 Technical data: - max. working width 4050 mm - max. cutting capacity St 40 6 mm - cutting gap adjustment - stroke rate depending on cutting length approx. 20 - 25 per/min - backgauge with positioning control ELGO 10 - 750 mm - Cutting length adjustment - hydraulic hold-down - front angle stop - front support arms laterally movable Guedpfoibmaxex Aa Sja - drive 400 V / 15 kW - foot switch - space requirement without support arms approx. W 4850 x H 2000 x D 2300 mm - weight approx. 10800 kg