Multifunctional chamber furnace

IVA MKG 70/95/160

Condition: used, Year of construction: 1996, pressure 80 t throat 320 mm stroke 6 - 118 mm no. of strokes 30 - 80 Hub/min ram adjustment 70 mm table surface area 830 x 610 mm ram surface 650 x 400 mm column daylight (nach hinten) 630 mm total power requirement kW weight of the machine ca. 8,1 t dimensions of the machine ca. B 1,2 x T 1,9 x H 3,3 m Cedpfxstycdke Aizsri Furnishing: - with gear transmission - fixed table - automatic stroke adjustment - automatic ram adjustment - hydr. Overload - Ejector - Grease central lubrication - Cover plate for drainage hole - Continuous speed control using a frequency converter - Machine is technically checked in our company and receives a new control cabinet with safety controls and touchscreen - current UVV test with braking time measurement

Condition: good (used), Year of construction: 2001, functionality: fully functional, Horizontal Boring Mill UNION T110 Year of manufacture: 2001 Travel axes: X: 1500 mm Y: 1250 mm (total vertical adjustment) 0 mm - lowest position of the spindle center to the table surface Credpfx Aijy Rpm Uozei Z: 1000 mm W: 550 mm (quill movement) B: 360° infinitely variable Spindle diameter: 110 mm Transmission steps: 2 Max. spindle speed: 4000 rpm Rapid traverse: 15 m/min Spindle taper: SK 50 Clamping table surface: 1000 x 1250 mm T-slot width: 22 mm Height of clamping surface above floor: 1050 mm Max. table load: 6 t Total weight (complete): approx. 13.5 t Control system: Heidenhain TNC 426 Electronic handwheel Various tool holders can be purchased additionally.

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate Csdpfjk S Htxex Aizsri - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: used, Year of construction: 2008, Technical details: batch weight: - total volume: 600 l external diameter: 1716 mm Effective volume: 345 l Work tank width: 1616 mm max. workpiece size: 270 mm revolution per minute: 980 - 1460 U/min total power requirement: 6 kW weight of the machine ca.: 1600 kg dimension machine approx.LxWxH: 2,4 x 1,7 x 1,44 m height: 3,42 m This machine was never operated with abrasive grinding media and therefore shows very little wear. The polyurethane lining is in excellent condition. The Walther Trowal CB 600 offered for sale was used exclusively for the treatment of stamped metal parts. The parts were processed in a dry finishing process using corn cob granulate, whereby they were conveyed through the media. The purpose of this process was to condition the surface of the stamped parts in such a way that sticking together during subsequent stacking was reliably prevented. The machine was used exclusively for this application and operated only in dry mode with corn cob media. Walther Trowal CB 600 The Walther Trowal CB 600 is an industrial circular vibratory finishing machine with a gross capacity of 600 liters. Suitable for: ·Deburring ·Edge radiusing ·Grinding ·Surface smoothing ·Polishing ·Descaling ·Cleaning metal parts Typical workpieces: ·Turned parts ·Milled parts ·Stamped parts ·Cast parts ·Forged parts ·Gears Machine can be demonstrated under power. i.D. Crodszdnlaspfx Aizsi *

Year of construction: 1980, condition: good (used), machine/vehicle number: 3253-80, Offer 22045 Approximate technical data: Cedpfsktg Dhjx Aizori - Pressing force 10 t - Overhang 150 mm - Table size 520 x 320 mm - Adjustable table height 160 mm - Through-hole in the table 165 x 125 mm - Overall installation height 220 mm - Ram area 240 x 150 mm - Dowel hole in the ram 30 mm - Ram adjustability 40 mm - Stroke adjustment 4 - 60 mm - Stroke rate 130 1/min - Hydraulically actuated clutch - Two-hand operation - Electric foot switch - Separate control cabinet - Drive 380 V / 1.1 kW - Space requirement approx. W 1000 x H 1800 x D 1100 mm - Weight approx. 1300 kg

Condition: good (used), Year of construction: 2000, The machine is being sold on behalf of a customer and can be inspected under power. Machine location: Czech Republic (Brno) Band saw automatic Behringer HBP 430A Year of manufacture: 2000 Crjdpfx Aoylmlijizji Saw band dimensions: 5800x54x1.3 mm Working area: round 430 mm / flat 430 x 430 mm Smallest material dimension: 15x10x15 mm Shortest cut length: 8 mm Cutting speed: 17 – 110 m/min Saw drive motor power: 7.5 kW Connected load: 11 kW Dimensions (LxWxH): 410 x 230 x 210 cm Weight: approx. 3400 kg

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, turning diameter over cross slide: 720 mm, turning length: 3,500 mm, turning diameter: 780 mm, spindle bore: 123 mm, swing diameter over cross slide: 780 mm, workpiece weight (max.): 3,000 kg, overall weight: 29,000 kg, Equipment: documentation/manual, rotational speed infinitely variable, Crodpfx Aiezkthtjzsi

Condition: used, Year of construction: 1993, machine/vehicle number: 493187, Lg. No. 21236 Hydraulic - twin-column guided miter - metal band saw Technical Data: - Cutting range at 90° Round 360 mm - Rectangle 600 x 360 mm - Cutting range at 45° Round 320 mm - Miter adjustment via handwheel - Saw band size 5400 x 38 x 1.3 mm - Cutting speed steplessly adjustable 19 - 130 m/min - Cutting pressure steplessly adjustable 0 - 10 m/min - Manual material clamping - Pre-selection of the stroke height of the saw band Crodpfx Aiowqpmnozji - Micro-spray coolant system - Total drive power 400 V / 8 kW - Space requirement ca. W 1800 x H 2000 x D 3250 mm - Weight approx. 2200 kg - Infeed + outfeed roller conveyors each approx. 6000 / 8000 mm

Condition: used, functionality: fully functional, power: 22.06 kW (29.99 HP), punching force: 250 t, EBU eccentric press suitable for inlay work, UV-tested Stroke adjustment from 10-140 mm Ram adjustment 80 mm Stroke rate 50 /min. Crjdpfxsv T Daps Aizei

Year of construction: 1987, condition: used, pressure 150 t throat 350 mm stroke 20-120 mm no. of strokes 50 / 75 Hub/min ram - range of adjustment 85 mm Cjdpfxop Apxhe Aizsri table surface area 1150x670 mm ram surface 800x380 mm hole in the table 330x200 mm table height 800 mm tool hole in ram Ø 50 mm weight of the machine ca. 8 t dimensions of the machine ca. BxTxH 2000x2000x2700 mm