Vertical Turret Lathe - Single Column

Jungenthal DK1400

Condition: good (used), Year of construction: 1963, functionality: fully functional, Single-Column Vertical Turret Lathe | Jungenthal DK 1400 The machine was overhauled in 1996, recently cleaned, and is in good condition. - Faceplate diameter: 1,200 mm Fjdpfx Aeyft Ahjg Asgc - Swing diameter: 1,500 mm - Turning height: 1,300 mm - Cross slide travel: 800 mm - Side slide horizontal traverse: 550 mm - Heidenhain Positip 855 digital readout - New operator panel - Various accessories Inspection is possible at any time by appointment.

Condition: used, Radial drilling machine CSEPEL type RFh 75 / 1500 Machine no. No. 13704 Year of construction 1985 Drilling capacity in steel Ø 75 mm Drilling capacity in cast iron Ø 90 mm Spindle holder MK 5 Nominal throat depth 1500 mm Largest projection of the spindle 1500 mm (to the column) Fodpfjlhwr Rjx Ag Aogc Smallest projection of the spindle 440 mm (to the column) Distance spindle nose - clamping surface 370 - 1700 mm Cantilever height adjustment 950 mm Table size / clamping surface 1800 x 1100 mm Column diameter 450 mm Pinol stroke 380 mm Spindle speed 19-1900 rpm 21 steps Feed rate 0.047-2mm/rev. 12 steps Motor power 11 kW Mains connection 380 Volt, 50 Hz, 15 kW - Clockwise/anticlockwise rotation of the drilling spindle via hand lever switch - Hydr. gear shift for spindle speed and feed speed - Hydro-mechanical central clamping - Motorized boom height adjustment - Without coolant device - Machine light - Operating instructions Space requirement: Length 2720 mm x width 1170 mm x height max. 3770 mm Transport height with motor on the column: 3500 mm Transport height without motor on the column: 3250 mm Weight: 6.3 tons good condition

Condition: good (used), Year of construction: 1963, Vertical lathe Fsdpfx Agsvi Hrye Aegc JUNGENTHAL Type: DK 1400 built in 1963 with 1 axis digital readout. turning diameter max : 1400 mm face plate : 1250 mm Automatic turret head spindle speed : 3,5-180 rpm feeds : 0,063 - 3,15 mm/rev rapid traverse : 1800 mm/min Further data see data sheet Machine documentation available . Dimensions : Length 4 m Width 2,4 m Height 3 m Weight 16t Good general condition .

Condition: used, Year of construction: 1965, faceplate diameter 1250 mm swing diameter 1450 mm Fsdjyqvriepfx Ag Ajgc turning height 1200 mm slide adjustment 800 mm side head - cross travel 600 mm Overhauled in 1996 Machine is cycle-controlled with Heidenhain Positip New control panel The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Year of construction: 1963, condition: ready for operation (used), functionality: fully functional, Swing diameter: 600 mm Turning length: 1000 mm Fsdpfx Aeyx Dtlsg Aegc Equipment: - Three-jaw chuck Ø 250 mm - Four-jaw chuck Ø 250 mm - Live centre - Quick-change drill chuck MK5 - Documentation

Condition: good (used), CHARACTERISTICS Plate diameter ⌀; 3200 mm Fgsder I Aykspfx Ag Asc Maximum turning/turning diameter ⌀; 3300 mm - With upright forward; 3300 mm - With upright set back; 5600 mm Min. turning/turning diameter ⌀ - With advanced upright; 800 mm - With upright set back; 3100 mm Max turning height; 750 mm Control; FAGOR 8025 Spindle RPM (2 ranges); - 0,5 - 10 rpm - 10 - 40 rpm Motor Power; 80 hp Maximum table load; 30.000 kg

Condition: good (used), Year of construction: 1984, max. wheel diameter 250 mm Fodov T Nqaepfx Ag Asgc gear width 275 mm max. module 6 weight of the machine ca. 5,5 t The gear hobbing machine ZFWZ 250 is suitable for the economical production of all hob-processable cylindrical gear types, such a: - spur and helical gear, wormgears and worms, splined shafts, keyed shafts, serrated profiles, chain wheels and ratchet wheels,as well as conical and crowned spur and helical gears. Interchangeable wheels and milling accessories Technical data: - Workpiece diameter (max): 250 mm - Module (max): 6 mm - Axial feed travel (max): 275 mm - Tangential feed travel (max): 100 mm - Tooth helix angle (max): 45 degrees - Milling cutter diameter (max): 145 mm - Milling cutter length (max): 170 mm - Table clamping surface (min): 195 mm - Table clamping surface (max): 470 mm Power Milling cutter speeds - Stepped in 2 ranges: 56 ... 250 rpm - (Standard version): 90 ... 400 rpm - Infinitely variable in 2 ranges: 63 ... 180 rpm - (special version DC motor): 140 ... 400 rpm Weights - Machine net: approx. 5000 kg - Electrical cabinet: approx. 800 kg - Hydraulic unit + coolant tank + chip transport: approx. 700 kg Overall dimensions (with oil mist filter) - Length: Standard version: 3950 mm DC drive: 3450 mm (or 3350 mm according to table) - Width: 3300 mm - Height: Machine: 1980 mm Machine with DC drive: 2150 mm Electrical cabinet: 2200 mm

Condition: good (used), Year of construction: 2005, travel distance X-axis: 12,000 mm, travel distance Y-axis: 3,500 mm, Technical Specification - X-axis (longitudinal travel - table): 12,000 mm - Programmable feed rate: 0.5 – 6,000 mm/min - Rapid traverse: 20,000 mm/min - Motor speed: 3,000 rpm Fodpfjyuxd Nox Ag Aogc - Y-axis (vertical travel / column): 3,500 mm - Programmable feed rate: 0.5 – 6,000 mm/min - Rapid traverse: 20,000 mm/min - Motor speed: 3,000 rpm - Rated torque (motor): 42 Nm Z - W-axis (spindle head): - Boring spindle diameter: 150 mm - Axial stroke of boring spindle (Z): 1,200 mm - Rapid traverse Z-axis: 20,000 mm/min - Internal taper of boring spindle: DIN 69871, ISO 50 - Spindle diameter: 254 mm - Spindle front bearing inner diameter: 200 mm - RAM dimensions: 400 x 400 mm - Axial stroke of boring spindle (W): 1,000 mm - Rapid traverse W-axis: 15,000 mm/min - Total axial stroke (Z+W): 2,200 mm - Rated torque spindle motor W and Z-axis: 42 Nm - Number of spindle gearbox speeds: 2 - Spindle speed range: 6 – 3,500 rpm - Spindle motor power: 60 kW Clamping plate sections: - Dimensions: 2 units @ 1,500 x 4,500 mm, 1 unit 2,000 x 4,500 mm - Load capacity: 15,000 kg/m² Workpiece table (axes V1 - B1 / V2 - B2): - Table dimensions: 2,000 x 3,000 mm - T-slot size: 28 mm - T-slot pitch: 180 mm - Table top height from floor: 650 mm - Load capacity: 40 t Tool rack magazine ATC 13-150 R 147 - Maximum magazine capacity: 147 tools - Maximum tool weight: 35 kg - Maximum tool length: 700 mm - Tool taper: DIN 69871 - Tool change time: 28 sec Milling head with indexed vertical axes, model TTL 2 18 360 - Tool holder: ISO 50, DIN 69871 EQUIPMENT: - CNC control: Heidenhain iTNC 530 - Electronic handwheel - Chip conveyor (manufactured: 2023) - CE marking - Documentation

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 510 mm, rapid traverse X-axis: 40 m/min, rapid traverse Y-axis: 40 m/min, rapid traverse Z-axis: 40 m/min, controller manufacturer: HEIDENHAIN, controller model: HEIDENHAIN TNC-620, total height: 2,500 mm, total length: 3,600 mm, total width: 2,500 mm, table width: 1,000 mm, table length: 450 mm, table load: 600 kg, overall weight: 5,000 kg, spindle speed (min.): 80 rpm, spindle speed (max.): 12,000 rpm, coolant supply: 20 bar, spindle nose: ISO 40, number of spindles: 1, number of slots in tool magazine: 30, tool length: 300 mm, tool diameter: 80 mm, tool weight: 8 g, input voltage: 380 V, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, USED "DOOSAN DNM 4500" vertical machining center with Heidenhain TNC-620 CNC Fedjw D Dy Njpfx Ag Ajgc

Condition: used, Year of construction: 1996, Technical details: pressure: 300 t chamfer lenght: 6000 mm control: Delem DA 24e distance between columns: 2x5100 mm throat: 645 mm dayligth: 520 mm plate thickness: 5 mm total power requirement: ca. 10,0 je machine kW weight of the machine ca.: ges. ca. 66 t Fedpfx Asu Ib Drog Ajgc dimensions of machine: L:12,0xB:2,3xH:3,65 m Hydr. Pressbrake 6000-300 - jib arm length= 720mm - incl. back gauge (without crowning system) adjustment travel horizontal/vertical: 680/200mm motoric Optionally, two of these press brakes can be offered - also applicable as a Tandem Pressbrake with 2x 6 meter with 300t, with table size: W:165xL.12000mm, - program sequence via both presse(synchronized) and single available Optional are tools available! Copy of documentation available i.D. *