Conventional Lathe - Servoturn 500/1000

Knuth Servoturn 500/1000

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Iaedpfx Alskvnumezer Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, functionality: fully functional, Used Schenck Balancing Machine H 50 V/B with used CAB 690 H measuring unit. (Can be upgraded to a new CAB 920 unit for an additional (18 000–20 000€) The machine comes with original foundation drawings, documentation and manuals. The machine can be test run in Kerava. Rotor Capacity Iajdpfxox Ein Ss Alzer - Rotor weight range: 20 – 6 000 kg - Maximum symmetrical load on pedestal bearing: 7 500 kg - Maximum symmetrical load on stand bearing: 3 750 kg - The machine can be loaded freely with lower weights when following recommended procedures. - Maximum rotor length between pedestals:1 600 mm (belt drive) - Maximum diameter over machine base: 2 100 mm - Clamped rotor diameter ranges: 25–180 mm, 180–380 mm - Machine bed length: 3 500 mm - Balancing speed n depends on the rotor’s moment and must be selected to avoid overloading the drive. - Maximum permissible G·n² value: 1400 × 10⁶ kg/min² - Applies to a rigid symmetrical rotor mounted on pedestal bearings. - May be exceeded during dynamic tests on flexible rotors and strength tests. - End drive / FU motor: 7,5 kW - 4-speed gearbox: 120–2520 rpm - Belt drive BU 5 / FU: 7,5 kW - Unbalance Umar 0,5 gmm/kg: 0 gmm/plane

Condition: used, Year of construction: 1998, workpiece weight 150 kg workpiece length 2500 mm diameter 160 - mm balancing speed variable 100 - 3000 U/min dia. axle journal 160 - 350 mm voltage 400 V total power requirement 1,5 kW weight of the machine ca. 1,5 t dimensions of the machine ca. 7,50 x 1,30 x 1,60 m Iedpfxswcg Elo Alzjar Control 0,60 x 0,60 x 1,85 m Software TIRA X9000 Operating System Windows XP Software update 2007 Serial No.: R 32/98 Max display sensivitiy: 0.5 gmm Balancing speed 100 - 3000 RPM

Condition: new, Bernardo horizontal bandsaw HBS 275-400 V Technical specifications Cutting capacity round 90 ° and 225 mm Cutting capacity 90 ° 200 x 200 mm square Section flat 90 ° 245 x 150 mm Cutting area around 45° 160 mm Section square 45 ° 160 x 160 mm Cutting area around 60 ° 100 mm Cutting range, square 60 ° 100 x 100 mm Working height 910 mm Band saw blade dimensions 2480 x 27 x 0,9 mm Cutting speeds of 400 V 45 / 90 m / min Coolant pump S1 100% 100 W S1 motor power output 100% 1,1 kW Motor power S6 40% 1,5 kW Voltage 400 V Iaedpfjd Du T Iex Alzjr Machine dimensions (L x D x H) 1430 x 720 x 1700 mm Weight approx. 190 kg Scope of delivery • Band saw blade • Workpiece stop • Base • Belt tension gauge • Vise with quick locking • Coolant system • Hydraulic lowering cylinder • Motor protection switch • Automatic shut-off

Condition: ready for operation (used), Year of construction: 1983, turning length 1500 mm turning diameter 475 mm turning dia. over face-slide 290 mm turning dia. in gap 655 mm turning speed range 14.0 - 2000 U/min feeds - longitudinal 0.05 - 0.736 mm/min spindle passage 61.0 mm tail stock MK 4 quill stroke 200 mm diameter of quill Ø 70.0 mm spindle head DIN 55022 GR 6 bed width 330 mm voltage 380 V total power requirement 7.5 kW weight 2400 kg range L-W-H 3080 x 1160 x 1485 mm From a maintenance workshop (university hospital) in good condition (!!) With original documentation + machine card Features: - Robust electric motor-driven conventional lathe - KLOPFER 4-jaw chuck Ø 200 Iedpoxfwc Refx Alzear - MULTIFIX steel holder with 3x inserts - Movable steel holder guard - Adjustable bed stop - Movable tailstock incl. center point - Swiveling machine light - Machine swing feet - Chip guard (movable from behind) - EMERGENCY stop button at the front - Original operating instructions + machine card

Condition: new, Year of construction: 2026, functionality: fully functional, workpiece weight (max.): 3,000 kg, Maximum Rotor Weight ---3000 kg (6613.87 lb) Minimum. Rotor Weight ---30 kg (66.14 lb) Maximum Rotor Diameter ---1400 mm (55.12 in) Minimum Shaft Diameter ---20 mm (0.79 in) Maximum Shaft Diameter ---300 mm (11.81 in) Motor power ---11 kW (14.75 HP) Drive Unit (Std.) ---11 kW (14.75 HP) Balancing Speed ---0-3000 Rpm (25 Hz) (up and down adjustable) Drive Unit --- Only Belt or Shaft / Belt + Shaft Isdpfx Ajr Dd Avolzear Bed length ---3000 mm (118.11 in)

Condition: used, Clamping plate, marking-out plate, measuring plate, measuring table, welding table, welding table, straightening plate -Clamping plate comes: from a measuring machine -Width: 1335mm -Length: 3000mm -Height: 250mm -Plate thickness: 40 mm -Plate is with: support ribs -with: 4x adjustable feet Iaodpfx Alsfc T Tqszer -Number: 1 piece available -Transport dimensions: 3000/1335/H750 mm -Weight: 2749 kg

Year of construction: 2016, condition: excellent (used), functionality: fully functional, Make: Reifenhauser Model: Mirex-MT-V 1-RZE 120-1800 Year: 2016 Condition: Excellent Use: PET / PP / PS Foil or Sheet Iedpfx Alsvbcbuszjar PET: Thickness Range: 0.25 - 2.2mm Output: 2,000 kg/h Max Sheet Width: 1600mm Extruder: RZE 120mm Electrical Supply: 3 x 480V 60Hz with N Calendar Roll Width: 1800mm Calendar Roll Diameters: 450 / 700 / 700mm Silicon Bath Max Sheet Width: 1600mm Silicon Bath Sheet Thickness Range: 0.15 - 1.5mm 4 Position Winder WOB 1800 for double web winding included. All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale.

Condition: new, Year of construction: 2025, functionality: fully functional, input voltage: 400 V, spindle speed (min.): 18,000 rpm, spindle speed (max.): 2,800 rpm, mount diameter: 300 mm, feed length Y-axis: 1,800 mm, Two-station CNC lathe – Efficiency, precision and productivity in the processing of cylindrical parts Iedpfowhbgujx Alzjar The CNC lathe with 2 working units and numerical control is a modern solution for the processing of wooden parts with a cylindrical shape – such as columns, table legs or decorative elements – offering accuracy, repeatability and efficiency in any workshop or factory. Double performance with independent units Equipped with two working units that operate simultaneously or independently, the lathe allows the rapid processing of parts up to 1200 mm. It is ideal for the series production of furniture components, church elements or artistic objects. Solid construction for durability The welded frame made of rectangular profiles, heat-treated, provides stability and torsion resistance. Linear guides on the X, Y and Z axes ensure precise, vibration-free movement. Precision through numerical control Hybrid servomotors, together with the rack and pinion system, guarantee precise positioning and efficient control on all axes. The manually adjustable tailstock with four clamping points stabilizes the parts during complex operations. Advanced motors and cooling Water-cooled motors allow operation at speeds of up to 18,000 rpm without overheating, ensuring a constant work rate and an extended service life. Intelligent DSP control The DSP control unit with internal memory allows for quick file import, project resumption from the stopping point and real-time parameter adjustment – ideal for a continuous and efficient production flow. Precision and maintenance auxiliary systems Self-centering chucks firmly fix the parts, while optical sensors and an automatic lubrication system ensure precision and low maintenance. Key advantages Perfect repeatability, even for large production runs Flexibility in operation with independent work units Robust construction and energy efficiency This CNC lathe is designed to deliver consistent performance, high quality and adaptability in woodworking, making it the ideal choice for modern workshops or furniture factories that aim to optimize production processes. Maximum working length 1200 mm Maximum working diameter (Ø) 300 mm Number of work units 2 pcs Control DSP Workpiece rotation speed 0 – 2800 rpm Motor power 4.5 kW Mill speed 18000 rpm Inverter “BEST” inverter Drive motors Servo motors – Hybrid Maximum feed 50 mm/ s Accuracy 0.0125mm

Condition: used, machine/vehicle number: 916183, Year of construction: 2012, operating hours: 2,526 h, lifting height: 5,500 mm, fuel type: diesel, power: 55 kW (74.78 HP), motor manufacturer: Perkins, gearing type: hydrostat, Lifting capacity: 3.000 kg Maximum passing height: 298 cm Front tyres / undercarriage remaining: 0 Rear tyres remaining : 0 Tyre brand: - Transport dimensions (LxWxH): 6.65x2.1x2.97 Please contact PFEIFER GROUP for more information Iaodpjtvlqxjfx Alzjr