Steinert Electro Magnetic Conveyor Belt

Condition: ready for operation (used), Year of construction: 2000, operating hours: 34,744 h, functionality: fully functional, machine/vehicle number: 258 032, overall weight: 11,500 kg, punching force: 20 t, positioning accuracy: 0.07 mm, tool diameter: 89 mm, TECHNICAL DETAILS Machine capacity: 196 kN (20 t) Air pressure: 5 bar Air consumption: 250 Nl/min Oil capacity: 160 l Ihedpfx Ajyn Nybebcow Turret speed: 25 rpm Travel Ranges Machine travel range without repositioning: 1,250 mm x 2,000 mm Machine travel range with 1 repositioning: 1,250 mm x 4,000 mm Machine travel range with 1 repositioning and 1 turning: Turning not possible Processing Max. sheet thickness with ball table: 6 mm Max. sheet thickness with brush table: 3 mm Max. table load: 100 kg Precision Punching accuracy (in standard mode): ±0.1 mm Positioning accuracy (repeatability): ±0.07 mm Control and Axes Pneumatic clamping devices: 2 Number of simultaneously controlled axes: 3 (X, Y, C) Performance Strokes per minute, feed 25.4 mm: X320 / Y250 Nibbling work cycle, feed 1 mm: X920 / Y920 Tooling Minimum programmable increment: 0.01 mm Number of tools: 31 Max. tool diameter: 88.9 mm Amadex stations: 2 x 11 1/4" + 1 x 2" MACHINE DETAILS Connected load: 30 kVA Operating hours: 53,497 h Cutting hours: 37,808 h Dimensions & Weight Dimensions (L x W x H): 4,890 x 4,370 x 2,137 mm Machine weight: 11,500 kg Note: No tools included, special transport required.

Condition: used, functionality: fully functional, Used Schenck Balancing Machine H 50 V/B with used CAB 690 H measuring unit. (Can be upgraded to a new CAB 920 unit for an additional (18 000–20 000€) The machine comes with original foundation drawings, documentation and manuals. The machine can be test run in Kerava. Rotor Capacity - Rotor weight range: 20 – 6 000 kg - Maximum symmetrical load on pedestal bearing: 7 500 kg - Maximum symmetrical load on stand bearing: 3 750 kg - The machine can be loaded freely with lower weights when following recommended procedures. - Maximum rotor length between pedestals:1 600 mm (belt drive) - Maximum diameter over machine base: 2 100 mm - Clamped rotor diameter ranges: 25–180 mm, 180–380 mm - Machine bed length: 3 500 mm Iodpfx Abox Ein Sscshw - Balancing speed n depends on the rotor’s moment and must be selected to avoid overloading the drive. - Maximum permissible G·n² value: 1400 × 10⁶ kg/min² - Applies to a rigid symmetrical rotor mounted on pedestal bearings. - May be exceeded during dynamic tests on flexible rotors and strength tests. - End drive / FU motor: 7,5 kW - 4-speed gearbox: 120–2520 rpm - Belt drive BU 5 / FU: 7,5 kW - Unbalance Umar 0,5 gmm/kg: 0 gmm/plane

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2003, load capacity: 1,500 kg, fork length: 1,100 mm, overall weight: 3,350 kg, total length: 3,100 mm, total width: 1,000 mm, TECHNICAL DETAILS Lifting capacity: 1,500 kg Ijdoyt Nl Iepfx Abcehw Fork length: 1,100 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 3,100 x 1,000 x 2,000 mm Weight: 3,350 kg EQUIPMENT Charger

Year of construction: 2018, condition: ready for operation (used), functionality: fully functional, Wave soldering system with comprehensive equipment! A spare parts package worth approximately €20,000 is included in the sale and delivery! The system comprises the following components: - Seho wave soldering system MWS 2340-F - Fluxer SelectFlux - Streamline transport system including lifts TECHNICAL DETAILS - PULSAR preheating: 2 convection and 5 pulsar preheating zones (3,300 mm length) - Wetting length (soldering system): 40 mm + 30 mm - Return transport level: raised 405 mm - Finger conveyor: L-shape, short (3 mm) MACHINE DETAILS - Number of processed solder frames: 1,060,540 pcs EQUIPMENT - Fluxer SelectFlux - Streamline transport system incl. lifts - Automatic solder bar feeder - Process gas cleaning system - Finger cleaning unit - Foldable convection top heater - Fan speed monitoring for convection preheating - Standard soldering unit - Wide solder nozzle unit, 7-row - Solder frame transport system incl. 2 lifts Ijdpfx Aeyt Nlbsbcjhw - Cooling tunnel in the return transport of the soldering system incl. timer control - Solder frame lowering station - Replacement filter for condensate trap at machine infeed and outfeed - Residual oxygen measurement with lambda probe - Nitrogen economizing circuit - Transponder system for automatic switching of soldering programs - Selective flux module (external unit) - Flow sensor for flux per spray head - Flux reservoir tank with connections - Replacement filters for external spray fluxer module – upper and lower machine sections - Spare PC

Condition: good (used), “Rentec Dinosaurus 2600S” for Sale Manufacturer: Rentec Type: Dinosaurus 2600 S Included Hydraulic-unit and control-unit build in container. With overhauled rotors. Ihjdpfx Abovt Tptjcjw Also outlet conveyor in stock which fits to the Rentec Dinosaurs 2600S. See PDF-file below for more detailed information.

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 003002, paper weight (min.): 35 g/m², paper weight (max.): 209 g/m², paper width (max.): 738 mm, paper height (max.): 1,300 mm, TECHNICAL DETAILS Max. paper size: 738 x 1,300 mm Min. paper size: 210 x 297 mm Sheet height: 1,200 mm Paper weight: 35 to 209 g/m² MACHINE DETAILS Power supply: Three-phase, 400 V Current: 12.6 A Connected load: 5.3 kW Dimensions (L x W x H): approx. 4,380 x 1,870 x 1,680 mm Ihedpfjyrnz Esx Abcsw EQUIPMENT PFU-74F pallet feeder User-friendly touchscreen control panel 6 folding pockets First knife fold and 2 pockets under the knife Second knife

Year of construction: 1998, operating hours: 297 h, condition: ready for operation (used), functionality: fully functional, saw blade diameter: 200 mm, rotational speed (max.): 3,000 rpm, screw diameter: 35 mm, machine/vehicle number: E0195/10, No reserve price – guaranteed sale to the highest bidder! Single-screw extruder with only 297 operating hours, including cutoff saw and haul-off unit! Hussmann ES35 x 30D TECHNICAL DETAILS Screw diameter: 35 mm Length: 30D MACHINE DETAILS Motor power: 16 kW Operating hours: 297 h Cutoff Saw TECHNICAL DETAILS Three-phase motor speed: 3,000 rpm Three-phase motor output: 0.55 kW Saw blade diameter: 200 mm Ihjdpfx Abeyrmzqjcsw Haul-off Unit TECHNICAL DETAILS Haul-off speed: 20/30/40/50/60 m/min Haul-off force: 11,700 / 7,800 / 5,800 / 4,700 / 3,900 N Contact length: 800 mm Max. belt width: 160 mm Max. profile height: 160 mm MACHINE DETAILS Drive power: 2 - 5.6 kW Weight: 800 kg EQUIPMENT Complete electrical and electronic control system with remote control box Digital speed display Ammeter 10-step helical potentiometer

Year of construction: 2000, condition: used, Drais Mannheim / Lödige CoriMix® CM Continuous Ringlayer Mixer Type: K-TT 700 Iodpfx Abjh H S Hdecjhw Motor: 55 kW 1500rpm Fully Stainless execution

Condition: ready for operation (used), Year of construction: 2024, functionality: fully functional, grinding width: 1,350 mm, overall weight: 2,500 kg, grinding height: 200 mm, The machine is equipped with the following processing units (further details can be found in the attached document): 1. Contact roller unit (250 mm diameter / cutting speed 18 m/sec / sanding belt 1370 x 2620 mm) 1. Sanding roller in grooved steel design 2. Contact roller unit (250 mm diameter / cutting speed 18 m/sec / sanding belt 1370 x 2620 mm) 2. Sanding roller in grooved steel design 3. Contact roller unit (250 mm diameter / cutting speed 18 m/sec / sanding belt 1370 x 2620 mm) 3. Sanding roller, 85 Shore TECHNICAL DETAILS Sanding height: 3 - 200 mm Sanding width: 1,350 mm Sanding belt dimensions: 1,370 mm x 2,620 mm Feed speed: 2.8 - 20 m/min MACHINE DETAILS Extraction connection: 3 x 200 mm Motor power: 18.5 kW (25.0 HP) Motor voltage: 50/60 Hz Electrics: 3x400V 50Hz CE version Vacuum table with blower: 4 kW (5.5 HP) Reversing function: 3 Weight: 2,500 kg Ihjdpfx Aoyub R Esbcow EQUIPMENT Feed table with electric height adjustment 3 motors: 18.5 kW (25 HP) each with SD start sanding belt brake Touch screen control with color display Additional extraction connection Note: The machine is delivered without a power cable. The electrical connection must be provided on site.

Condition: ready for operation (used), Year of construction: 1995, functionality: fully functional, bar passage: 34 mm, controller model: Fanuc 21T Modell B, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Bar capacity: 34 mm MACHINE DETAILS CNC control: Fanuc 21T Model B Iodpeyrf Ensfx Abcohw EQUIPMENT CS axis left CS axis right Approx. 26 fixed tool holders 2x driven tool holders (1x axial, 1x radial) Hainbuch collet chucks left and right Chip conveyor Manuals Note: The bar feeder is not included in the offer.

Condition: used, Used Crusher for Filter Cake / Lump Breaker Drive: Lenze Isdpjbpia Dsfx Abcshw The crusher for filter cake or lump breaker consists of two horizontal rotating shafts.

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, overall weight: 8,700 kg, workpiece length (max.): 165 mm, workpiece diameter (max.): 35 mm, production capacity: 7,200 unit/h, TECHNICAL DETAILS Number of cavities: 6 Max. output: 7,200 bottles/h Product dimensions Max. preform length: 165 mm Iedpfsyrfvgox Abcjhw Preform diameter: 18–35 mm Ring diameter: 27–42 mm Max. neck finish diameter: 38 mm Neck height: 9–27 mm Max. bottle height: 350 mm Max. bottle diameter: 105 mm Max. bottle volume: 2 l MACHINE DETAILS Dimensions & Weight Blow module (L × W × H): 3,293 × 2,325 × 3,196 mm Control cabinet (L × W × H): 1,998 × 602 × 2,410 mm Blow module: 6,300 kg Control cabinet: 1,200 kg Preforms feeder: 1,200 kg Total weight: 8,700 kg Noise level: 83 dB(A) Installed power Installed power: max. 160 kW Reference consumption (1,500 ml bottle): 88 kW Reference consumption (1,000 ml bottle): 62 kW Reference consumption (500 ml bottle): 45 kW Infrared heating (9 zones): 132 kW Operation and feed system: 28 kW Power supply Supply voltage: 230/400 V ±10 % Frequency: 50 Hz ±1 % Cooling water Cooling capacity: 20,000 kcal/h Water temperature: 8–12 °C Flow rate: max. 5 m³/h Pressure: 3–5 bar Compressed air Air consumption at 40 bar (0.25–2 l bottle): 180–700 Nm³/h Air consumption at 7 bar (operating air): 35 Nm³/h

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 207000046, paper weight (min.): 50 g/m², paper weight (max.): 300 g/m², production capacity: 19,680 unit/h, No reserve price – guaranteed sale to the highest bidder! Original purchase price of the printer: €143,250! Production printer with the following configuration: - Input Interface Module-B1 - Paper Input Module Standard-B1 - Paper Input Module Optional-B1 - Océ iHCS2.1 TopCover-B2 TECHNICAL DETAILS Printing speed A4: up to 328 ppm Printing speed A3: up to 171 ppm Maximum monthly print volume: up to 10,000,000 A4 pages Resolution: 600 x 1,200 dpi Paper specifications: Total paper weight range: 50 gsm – 300 gsm Plain paper (Canon recommended media): 50 – 300 gsm Coated media (Canon recommended media): 80 – 250 gsm Paper format: 203 x 203 mm to 350 x 500 mm MACHINE DETAILS Main unit dimensions: Main unit dimensions (W x D x H): 1,439 x 1,070 x 1,225 mm Main unit weight: 779 kg Meter readings: A4 simplex: 67,535 A4 duplex: 52,601,622 A3 simplex: 0 A3 duplex: 3,853 Iedeyrd Rcopfx Abcehw SYSTEM CONFIGURATION - 4x Paper Input Module - 8x Duo Paper Tray - 2x High Capacity Stacker - Remote Manager - PCL, IPDS, PostScript - Streaming & PrismaSync

Condition: ready for operation (used), Steinert Electro Magnetic Drum Brand: Steinert Dimension drum : Lenght 1300 mm , Ø 500 mm. Isdpfx Abju Tlr Iocehw Driving: 4 kW Gearbox. Power drum = 3 kW. Including new rectifier.

Condition: ready for operation (used), Year of construction: 2023, machine/vehicle number: 23-07-12-045, functionality: fully functional, power: 7.5 kW (10.20 HP), saw blade diameter: 550 mm, table height: 910 mm, cutting width at rip fence: 1,000 mm, The machine is in very good condition with minimal signs of use! Ihsdpfsytpxnsx Abcjw The machine was used for processing aluminum. TECHNICAL DETAILS Maximum blade diameter: 550 mm Cutting width at CNC parallel fence: 1,000 mm MACHINE DETAILS Machine height: 910 mm Motor power: 7.5 kW EQUIPMENT Table extension: (length: 840 mm) Double roller carriage (length: 3,000 mm) 2 pneumatic quick clamps (application range: 0–90 mm) Eye-level control panel Template holder directly at the control unit Increased cutting height including saw blade tilting TIP-SERVO DRIVE CNC angle fence UNO 90 Additional cross slide incl. connection Front support roller Air cushion table Spray device Note: The machine comes from a business liquidation, has been professionally dismantled and placed in storage.