Cantilever racks & heavy pallet racks

Condition: ready for operation (used), Year of construction: 2013, operating hours: 29,764 h, functionality: fully functional, machine/vehicle number: 6640-105136, load capacity: 235 kg, arm reach: 2,550 mm, controller model: IRC5, repeat accuracy: 0.05 mm, number of axes: 6, TECHNICAL DETAILS Load capacity: 235 kg Reach: 2,550 mm Repeatability: ±0.05 mm Axis 1: +170° to -170° Axis 1 optional range of motion: +220° to -220° Fedezxqcwspfx Aatspl Axis 2: +85° to -65° Axis 3: +70° to -180° Axis 4: +300° to -300° Axis 5: +120° to -120° Axis 6: +360° to -360° Axis 6 standard rotation range: ±96 revolutions MACHINE DETAILS Controller: IRC5 Operating hours: 29,764 h EQUIPMENT Manipulator IRC5 controller cabinet All cable sets Teach pendant

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) Fpjdpfxergzv Nj Aatol * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, overall weight: 6,600 kg, year of last overhaul: 2025, Overhaul work 2025 - Lifting devices overhauled - Bottle carousel overhauled - Glue roller overhauled - Roller motor replaced - New protective covers installed - Printing heads overhauled - All sensors of the glue heating system replaced - Hoses of the extraction unit replaced - Entire electrical system inspected Fsdozv Rp Sspfx Aatjpl TECHNICAL DETAILS Output: 45,000 bottles/hour Bottle format: 500 ml, 1 l, 1.5 l Labeling system Labeling method: Roll-fed / roll labeling Label placement: Wrap-around labeling Rotation direction: Clockwise Carousel movement: Mechanical cam drive with brake/clutch Optical centering system: Mechanical Head adjustment: Manual Number of bottle carousels: 25 Number of labeling stations: 2 MACHINE DETAILS Mains voltage: 400 V Mains frequency: 50 Hz Power consumption: 35 kW Current consumption: 57 A Machine weight: 6,600 kg EQUIPMENT - Mechanical cam drive with brake/clutch for bottle carousel movement - Mechanical optical centering system - Manual head adjustment - Roll-fed labeling system for wrap-around labels - Two labeling stations - Safety guards

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2010, Submitting a bid obligates you to collect the item by September 21, 2026! TECHNICAL DETAILS Sheet size: max. 3,048 x 1,524 mm Z-axis stroke: 70 mm Sheet thickness steel: 20 mm Sheet thickness stainless steel: 20 mm Sheet thickness aluminum: 12 mm Positional deviation Pa: ± 0.1 mm/m Positional scatter Ps: ± 0.05 mm Table load capacity: 750 kg Table changeover time: approx. 35 s Positioning speed X/Y axis parallel: max. 100 m/min Positioning speed X/Y axis simultaneous: max. 140 m/min Axis acceleration X/Y: max. 12 m/s² Cutting speed: max. 50 m/min MACHINE DETAILS Beam source: ByLaser 4400 Fedezwmn Topfx Aatopl Laser type: CO₂ laser Laser power: max. 4,400 W Wavelength: 10,600 nm Machine weight: 12,000 kg Laser weight: 1,700 kg EQUIPMENT 2 cutting heads with 5-inch and 7.5-inch lenses

Condition: used, Year of construction: 1978, operating hours: 9,125 h, 1978 | Hanomag MF 33C Massey Ferguson / for parts only | Used Wheel Loader | 9125 hours 📍Location: Germany 🚛 Delivery available to your destination – Use our shipping calculator to estimate transport costs! Fpsdpfxey Iy N Uj Aatel 💰 Buy Now for EUR 4900 or Make an Offer. Payment at delivery available for an affordable fee (subject to approval)* 👷‍♂️ Inspected by an independent expert 5 inspection points 5 approved ✅ 0 imperfect ℹ️ 0 issues ⚠️ 📌 Inspector's Comment: Only for parts recovery, not complete. 📄 Want to see the full inspection, extra photos, or a video? Tip: The reference "40580 Equippo" is commonly used when looking up more details online. 💡 Why this machine and our service stands out: ✔ Thorough inspection by professionals ✔ Jobsite delivery available ✔ Money-Back Guaranteed ✔ Secure and flexible payment options 🔄 Considering other equipment options? We offer helpful tools and resources for all equipment owners and operators – easily accessible on our platform.

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 31-44336, travel distance X-axis: 630 mm, travel distance Y-axis: 630 mm, travel distance Z-axis: 630 mm, workpiece weight (max.): 500 kg, spindle speed (max.): 24,000 rpm, No minimum price – guaranteed sale to the highest bidder! The machine spindle has been completely overhauled! TECHNICAL DETAILS Travel range X-axis: 630 mm Travel range Y-axis: 630 mm Travel range Z-axis: 630 mm Pallet size: 400 × 500 mm Number of pallets: 6 Pallet change time: 9 s Max. workpiece size: 720 × 800 mm Max. workpiece weight: 500 kg NC rotary table: B-axis B-axis rotation range: 360,000 × 0.001° B-axis rotation speed: 40 rpm Tool holder: SK 63 Max. tool diameter: 150 mm Max. tool length: 227 mm Max. tool weight: 12 kg Fpsdpfx Aozwd Htoatsl Spindle speed: 45–24,000 rpm Spindle torque: 48/72 Nm Spindle drive: 30 kW Feed rate X/Y/Z: 1–60,000 mm/min Rapid traverse X/Y/Z: 60,000 mm/min Feed force: 10,000 Nm MACHINE DETAILS Total connected load: approx. 60 kW Connection voltage: 400 V Mains frequency: 50 Hz Total weight: approx. 12,500 kg EQUIPMENT Chip conveyor Documentation/Manual

Condition: ready for operation (used), functionality: fully functional, shovel volume: 1.2 m³, Year of construction: 2017, operating hours: 1,650 h, Equipment: pallet forks, TECHNICAL DETAILS Earthmoving bucket volume: 1.2 m³ 4-in-1 bucket volume: 0.7 m³ Clamshell bucket width: 250 cm MACHINE DETAILS Maximum speed: 40 km/h Fpodpfx Aaszylz Dotsl Operating hours: 1,650 h EQUIPMENT Pronar 2600 dozer blade, two-piece, fully hydraulic Pallet fork Note: The wheel loader has been reclassified as an agricultural towing vehicle up to 3.5 tons. A tested tow hitch and trailer socket have been installed for this purpose. This allows for the possibility of applying for a green license plate.

Condition: good (used), Year of construction: 2004, functionality: fully functional, cutting length (max.): 1,00,000 mm, feed length X-axis: 5,050 mm, saw blade diameter: 550 mm, type of input current: three-phase, saw blade speed: 2,800 rpm, input voltage: 380 V, air pressure: 6 bar, overall weight: 1,800 kg, The Twin Electra 550 is a dual miter saw with 3 axes and an automatically adjustable saw head on linear guides. Electronic control of all miter angles via a brushless motor, from 45° (inward) to 22°30’ (outward), with a precision of 240 positions per degree. Connection to window construction software (orgadata / Unilink / Wictop... etc.) is possible. Fjdezav U Nopfx Aatopl The machine features the following equipment: - Industrial PC - Additional clamping device on the roller conveyor - Automatic profile support - Shortcut function - Overlength cutting - Crosscut - Automatic cutting - Connection to external software possible (Orgadata, Unilink, Wiktop... etc.)

Condition: used, Year of construction: 2017, operating hours: 1,113 h, machine/vehicle number: G30XL320839, TECHNICAL DETAILS Zünd G3 XL-3200 Plotter Vacuum system: 1–9 kW Tool heads Universal tool head UM-ZS G3, working width: 60 mm Universal tool head UM-ZP G3, working width: 60 mm Operating hours: 1,113 h EQUIPMENT Zünd G3 XL-3200 Plotter, item no. 6343200 G3 vacuum system, CIC, item no. 6438104 ICC camera for S3/G3, item no. 6539101 UM-ZS G3 universal tool head, item no. 6531006 UM-ZP G3 universal tool head, item no. 6531007 Universal cutting tool (UCT), item no. 6532001 EOT-250 oscillating tool, G3, item no. 6532018 V-CUT tool, G3, item no. 6532021 Creasing tool type 1 (CTT1), item no. 6532051 Creasing tool type 3 (CTT3), item no. 6532053 Zünd Cut Center software package, item no. 6731200 Zünd Cut Center camera option, item no. 6731250 Zünd Cut Center V-Cut option, item no. 6731240 PC and monitor for Zünd Shipping costs for the plotter Fpsdpfx Aaezyktlotel

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, overall weight: 3,500 kg, No minimum price – guaranteed sale to the highest bidder! Fpsdpfx Aaezyccxotol TECHNICAL DETAILS Cutting range at 90° (round): 530 mm Cutting range at 90° (flat): 530 × 800 mm Cutting range at 45° (flat): 530 × 520 mm Cutting range at 30° (flat): 530 × 320 mm Cutting angle: 45° - 0° - 60° Blade speed: 20–120 m/min Feed length: 1,500 mm MACHINE DETAILS Saw motor power: 3.0 kW Coolant pump: 100 W Hydraulic pump: 370 W Power connection: 400 V / 50–60 Hz Dimensions & Weight Dimensions (L × W × H): 2,500 × 4,000 × 2,500 mm Total weight: 3,500 kg EQUIPMENT Machine stand with chip collection tray Hydraulic cutting pressure control Stepless blade speed control Hydraulic guide arm adjustment Minimum quantity lubrication Automatic shutdown at the end of the cut Chip brush Hydraulic miter adjustment Hydraulic clamping device Hydraulic blade tensioning Operating manual

Condition: new, Year of construction: 2023, Welding turntable, container rotating device, 6000 kg load capacity Digital display with foot-operated remote control Diameter from 180 mm to 3500 mm Fpodpfx Aask Adl Hotol Drive roller diameter 300 mm Dimensions: Length: 1900 mm x Width 470 mm x Height 390 mm Speed, continuously variable: 200 - 1800 mm/min.

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 2018/219, hole diameter: 75 mm, number of planer blades: 6, operating speed: 6 mm/s, year of last overhaul: 2018, For sale is a very fast and complete Cambio debarking system! In 2018, the machine was completely overhauled, and since then, it has been professionally maintained and equipped with a new knife ring with 6 cutting knives! The system can be directly integrated into your existing mechanization! TECHNICAL DETAILS Maximum log diameter: Ø 750 mm Minimum log diameter: 11 cm Shortest log length without an additional feed system: 3 m Shortest log length with an additional feed system: 1.5 m Maximum feed speed: 100 m/min MACHINE DETAILS Rotor motor: 55 kW Feed motor: 11 kW Hydraulic power: 1.5 kW Rotor speed: 220 rpm at 50 Hz Rotor opening: 80 cm Debarking rotor: 6-knife rotor Weight: 10,500 kg EQUIPMENT Complete infeed system Complete outfeed system Electrical system Hydraulics for the infeed rollers New 6-knife rotor from the 2018 overhaul Complete debarking system for integration into an existing mechanization Centering device ZV – 75/2 MA Number of horizontal conical rollers: 2 Drive power per SEW worm gear motor: 1.5 kW EQUIPMENT 2 horizontal conical rollers mounted in pneumatically actuated swivel arms SEW worm gear motors with torque supports in a solid steel design Heavy-duty inlet hopper Complete sensor system Outfeed system AW 800 Fsdpfxjzx Eaqe Aatjpl Drive power: 3.0 kW EQUIPMENT Drive via SEW spur gear motor Machine frame made of welded rectangular tubes for supporting additional machine components Hydraulic shock absorbers

Condition: ready for operation (used), Year of construction: 2010, machine/vehicle number: 0-240-06-8502, functionality: fully functional, power: 18 kW (24.47 HP), cutting height (max.): 95 mm, saw blade diameter: 380 mm, cutting length (max.): 4,300 mm, plate width: 2,200 mm, TECHNICAL DETAILS Cutting length: 4,300 mm Panel width: 2,200 mm Saw blade overhang: 95 mm Main saw blade diameter: max. Ø 380 mm Fodpfx Ajzx Anxeatspl Saw carriage feed rate: up to 150 m/min Clamping jaws: 7 pieces MACHINE DETAILS Main saw motor power: 18 kW Scoring saw motor power: 2.2 kW Operating hours: approx. 38,544 h (as of 05.10.2023) EQUIPMENT Automatic rear panel loading system Lift table loading system Lift table Automatic program slider with clamping jaw feed Main saw unit Scoring unit Automatic cutting length and positioning control Angle and back stop Air cushion support tables in the operator area CADmatic operating and optimization environment PICA 108 label printer Roller and transport technology in the rear loading area Safety enclosure with protective fencing Dust extraction connections with machine-side dust extraction ducting

Condition: good (used), Frame: 8800x1050x80 mm, 32 pieces Crossbars: 1860*75*45 mm (2800 kg/shelf), 352 pieces Partial quantities can also be purchased. If you require shelving or accessories in different configurations or designs, please contact us. We offer a comprehensive range of new and used shelving, as well as accessories, and will be happy to assist you with your planning. A customized offer tailored to your specific needs is a matter of course for us. Shipping: Please inquire about shipping costs, providing your postal code and location, as well as the desired quantity of items. Fjdsd Hbqnepfx Aatopl

Condition: ready for operation (used), Year of construction: 2010, machine/vehicle number: 0-201-08-1422, functionality: fully functional, operating hours: 17,952 h, number of slots in tool magazine: 24, working width: 1,600 mm, spindle motor power: 15 W, number of spindles: 2, working length: 4,760 mm, Machining center with automatic material handling (serial number: 0-205-08-1424) TECHNICAL DETAILS Travel in X-axis: approx. 4,760 mm Travel in Y-axis: approx. 1,600 mm Main spindles: 2 Power of main spindles: 15 kW each Tool interface: HSK F63 Number of drilling heads: 2 Tool changer: 2 × 12-position Fpedpfxozx Anfe Aatsl MACHINE DETAILS Control system: PC85 / woodWOP Operating hours CNC: 17,952 h EQUIPMENT Automatic AP console tables Chip and waste disposal Safety enclosure Associated HOMAG handling and return conveyor system Portal handling Vacuum crossbar Conveyor technology C-axes FLEX-5 preparation Automatically positionable vacuum clamps Liquid ring vacuum pumps Note on machine designation: BOF 712/48/16/AP was the actual historical machine type. CENTATEQ E-500 is the later/current model designation, which is now visible on the machine.