Used Camam Knurling for sale (85)

Condition: new, machine/vehicle number: 7272fc3b6a97f9be58a222f05, empty load weight: 5 kg, maximum load weight: 32 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Fine-grained steel welded construction, fifth wheel plate with interchangeable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with incl. guide wedges on both sides Incl. guide wedges, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 30 foot or 1 x 40 foot container. Adjustment via central telescope as an interlocking central tubular frame with bolt lock. Optimum fifth wheel load when transporting 30 foot and 40 foot containers. 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Hydraulics 100 Low-pressure cylinder max. 150 bar, with HDK screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Incl. Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 170 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable Dkjdpfx Aji Riv Eja Nsl EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck instal. calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light

Year of construction: 2021, condition: new, machine/vehicle number: 2021052701, Aluminium flat belt conveyor without substructure conveyor belt length: 6000mm drive roller: knurled deflecting roller: crowned PVC conveyor belt Conveyor belt EM 15/2 0+17 PVC blue FDA compliant according to EU10/2011 Belt width 500mm outside corrugated edge welded on both sides 40mm high T-30 cleats (61 pcs) - 200mm pitch * antistatic due to threads in the fabric of the running side endless welded with stepped finger joint food certificate is included V2A stainless steel underlay plate full surface drive: motor approx. 1,1KW - horizontally lying Dsdpfeg D T N Hjx Aa Nokl * optionally controllable with frequency converter connection 220/

Year of construction: 2021, condition: new, Aluminum flat conveyor belt without substructure conveyor belt length: 4000mm drive roller: knurled deflection roller: crowned overturned Our core competence is to supply the customer exactly what he really needs. Together with our customers, we work out customer-specific, individual solutions and deliver corresponding systems from our own production. Please contact us by phone to find a suitable solution for your application. PVC conveyor belt Conveyor belt EM 15/2 0+17 PVC white FDA compliant according to EU10/2011 Belt width 500mm outside corrugated edge welded on both sides 40mm high T-30 cleats- 400mm pitch * antistatic due to threads in the fabric of the running side endless welded with stepped finger joint food certificate is supplied V2A stainless steel carpet pad plate full surface drive: motor approx. 1,1KW Dksdpfxohfwcbj Aa Nsl * optional controllable with frequency converter connection 220/400V

Condition: new, Year of construction: 2024, Bending machine ZB 70/2 H- with foot pedal- with standard roller setTECHNICAL SPECIFICATIONS:- two driven shafts, knurled surface - hydraulic adjusting of the center roller- working position horizontal and vertical - digital readout with memory- shafts are supported by conical bearings- slide bars on the slide-support are exchangeable- shaft diameter: 40 mm- roller diameter: 152/162 mm- shaft rpm: 8,5 U/min- voltage: 400V 50Hz 3Ph- drivingmotor: 1,1 kW- motor for hydraulic: 1,1 kW- hydraulic pressure: 8 to.- adjusting way: 120 mm- weight: 470 kg- dimensions: 900x600x1100 mm Dkodedktnkopfx Aa Njl

Year of construction: 1993, condition: used, - working width (mm): 2200 - engine power (kW): 22 - top rollers: with PU rings - bottom rollers: knurled Dedpfx Asn I Twysa Njkl - Saw shaft: included

Condition: good (used), Year of construction: 1989, functionality: fully functional, machine/vehicle number: AN-No.: 88.04.017 D, 8 very clean (reworked) Jakob Müller Frick AG looms NF42 from 1988, 1989 and 1990 from my stock. Machines run perfectly, 100% functional (refurbished) 12 shafts, without creel, with Mütrans, partly Müdata 1 piece NF 2/84mm from 1989 for 6.900€ AN-No.: 88.04.017 D with Müdata and Mütrans, 16 stocks 3 pieces NF 2/84mm overhauled from 1990 for 6.500€ each AN-No.: 90.01.704 B AN-No.: 90.01.755 A AN-No.: 90.01.229 A 1 piece NF 2/84mm overhauled from 1989 for 6.500€ AN-No.: 89.00.118 D 3 pieces NF 2/84mm refurbished from 1988 for 6.500€ each AN-No.: 88.04.244 A AN-No.: 88.02.758 A AN-No.: 88.02.758 B The machines come from a curtain band production and were originally equipped with a Z compartment. They were converted to standard compartments as part of the general overhaul. Dogonl All tension trees and press rollers have been newly vulcanized by Westland. The card rollers in the chain case are also new or newly vulcanized. The central lubrication in the chain case has been optimized by us. All machines have the first shaft free (for heavier reeds) and have 12 shafts installed. All machines are equipped with Mütrans II. Individual machines with double belt take-off (heavy fabrics) can optionally be supplied. I think possible for 4-5 machines. It is also possible to equip it with finely knurled tension trees. I think it is also possible for 4-5 machines. All needle holders are suitable for double needles. For this purpose, two additional Mütrans II can be installed upon request. The machines have been rebuilt from scratch. All bearings, shafts and bushings have been checked and replaced if necessary. All swing arms have been checked and replaced if necessary. Installed are: 1st shaft free (spacer block installed) 2nd and 3rd shaft swingarm 201 Djdpjr Ix Igefx Aa Njkl 4th - 6th shaft swing arm 202 7th - 9th shaft swing arm 203 10th - 12th shaft swing arm 204 13th shaft swing arm 205 All shaft springs have been checked and replaced if necessary. Nothing is porous, cracked or defective. The electrical installation has been checked, the circuit board for the thread monitoring has been checked and, if necessary, repaired or replaced. The machines are painted in RAL 6021 Müller pale green. All panels are clean and free of damage. The machines come without Müdata. 4 machines are also equipped with a crawler gear. The machines have been set up and tested. The machines come without oil, strands, slats, reeds, needles and chain links. Delivery on a Euro pallet, FOB Wuppertal

Condition: used, TECHNICAL DETAILS - Min/max. grindable diameter: 1 - 100 [mm] - Max. length of the workpiece when plunging : 140 [mm] - Min/max work wheel diameter: 440/610 [mm] - Max. working wheel width: 80 [mm] - Peripheral grinding wheel speed: 50 [m/s] - Speed with new work wheel: 1565 [rpm] - Min./max. drive wheel diameter: 220/305 [mm] - Max. width of drive wheel: 67 [mm] - Max. drive wheel inclination: +/- 7 [°] - Drive wheel speed during machining: 0/140 [rpm] - Drive wheel speed in dressing: 200 [rpm] - Total installed power: 41 [kW] - Dimensions : 5920 x 5071 x 2500 [mm] - Net weight: 7000 [kg] EQUIPMENT - CNC SIEMENS 840D control - 5 numerical axis (1 for working grinding wheels facing device, 2 for driving grinding wheels facing device, 1 for upper slide, 1 for lower slide) - working grinding wheels facing device by diamond knurling wheel - driving grinding wheels facing device by diamond center - automatic parts feed bowl - parts conveying strip Dkodpfxjuhb R Ao Aa Nol

Condition: used, TECHNICAL DETAILS - Min/max. grindable diameter: 1 - 100 [mm] - Max. length of the workpiece when plunging : 140 [mm] - Min/max work wheel diameter: 440/610 [mm] - Max. working wheel width: 80 [mm] - Peripheral grinding wheel speed: 50 [m/s] - Speed with new work wheel: 1565 [rpm] - Min./max. drive wheel diameter: 220/305 [mm] - Max. width of drive wheel: 67 [mm] - Max. drive wheel inclination: +/- 7 [°] - Drive wheel speed during machining: 0/140 [rpm] - Drive wheel speed in dressing: 200 [rpm] - Total installed power: 41 [kW] - Dimensions : 5920 x 5071 x 2500 [mm] - Net weight: 7000 [kg] EQUIPMENT - CNC SIEMENS 840D control - 5 numerical axis (1 for working grinding wheels facing device, 2 for driving grinding wheels facing device, 1 for upper slide, 1 for lower slide) - working grinding wheels facing device by diamond knurling wheel - driving grinding wheels facing device by diamond center - automatic parts feed bowl - parts conveying strip Djdouhb R Njpfx Aa Njkl

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 0803024, planing height: 130 mm, spindle diameter: 50 mm, planing width: 230 mm, spindle speed (max.): 6,000 rpm, The machine is provided free loaded. Dkedpfxjxa Dzis Aa Nol TECHNICAL DETAILS Max. workpiece dimensions: 130 x 230 mm Thickness: 10 to 130 mm Width: 15 to 230 mm Minimum length, single piece: 600 mm Minimum length with universal lantern: 760 mm Maximum cutting depth: 10 mm Spindle speed: 6,000 rpm Spindle diameter: 50 mm MACHINE DETAILS Dimensions & Weight Operational dimensions (W x H): 3,000 x 2,250 mm Dimensions: 5,100 x 2,000 x 1,810 mm Weight: 4,300 kg General power supply: 400 V, three-phase + N, 50 Hz Installed power: 53 kW Current consumption: 95.6 A EQUIPMENT Five tool holders with reinforced motors Chrome table 3.00 m Soundproofed and secured covers with gas pressure springs Digital counters (type Siko) for precise manual adjustment Control panel elevated and operator-side Infeed table made of cast steel (L x W): 2,980 x 255 mm Side-mounted, spring-loaded feed unit Digital chip removal indicators Five spindles with detailed power distribution Pneumatic pressure rollers Smooth and knurled steel rollers Smooth steel roller at the outfeed Overhauled and mounted knives Operating manual List of spare parts and circuit diagrams

Year of construction: 1998, condition: excellent (used), machine/vehicle number: ExCello Serial Number 3888, MICHIGAN Rotoflo Type 3237 Cold Forming Machine. Original Serial Number: 4590 ExCello Serial Number 3888 New 1975 rebuilt by ExCello late 1990’s Country of Origin: USA For the coldforming of profiles for serrations (straight or angular), spiral teeth, oil grooves, threads and knurls. Capacity: Maximum slide stroke 1065 mm Maximum rack length 915 mm Maximum profile diameter 50 mm Maximum profile length 125 mm Dedpfofnk Ehex Aa Nskl Standard module range 0.3 to 1.25 Motor size 15 kW Hydraulic tank capacity 1000 l Overall floorspace width of machine 5014 mm Width of machine 2768 mm Depth with outboard support 4165 mm Height 2000 mm Approximate weight of machine 11,700 kgs Complete with: Hydraulically operated outer support assembly to accommodate part length universal headstock, Universal rack holding feature.