VACUUM DRY KILN for massive wood

MASPELL E10

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Kjdpfx Aov Si Szsarjdw Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: new, Year of construction: 2024, functionality: fully functional, Wood thermal modification kiln fully equipped for thermo wood production, included: 15 m high AISI 316L isolated double wall chimney, inlet/outlet piping, pressure valves, gages, air compressor, full wood pellet heating unit, Siemens control panel, timber loading/unloading platform, 2 sets of timber spacers. Timber volume 7...8 m3, depends on bord dimensions and length; Inner chamber for timber length up to 7,5 m, total kiln length 10 m; Full thermal modification cycle time ~24 h from heating up to cooling down; Temperature can be set up to 230°C or more if needed; Kjdpfx Aaevzub Horsdw Required nominal grid power 25 A, can be used without grid with power generator; To produce 1 m3 thermally modified timber: 9...10 kWh + 55...60 kg wood pellets = 16...20 EUR without labor costs; Our wood thermo modification kilns can be made according to customers needed length from 3,6 to 9 m (from 3 to 9 m3 timber volume);

Condition: used, Year of construction: 2025, The CORMAK BS 260G band saws, due to being equipped with a hydraulic cylinder, a cooling and an arm swivelling up to 60°, together with blades from renowned German Röntgen company, are used commonly in ironworking where precision, quality and cutting speed are important. Horizontal band saw with a swivelling arm for cutting metals, allows for cutting in plane perpendicular to the axis of material cut and at any angle from 0 to 60º. Material for cutting can be fed manually or by any mechanical feeding device, with automatic tool feed. Band guides are equipped with dedicated carbide plates and bearings. This has a huge impact on band guiding, its durability, cut straightness, cutting accuracy and quality. Machine's arm is made of profiled CAST IRON. Control panel is located by the arm. The drive from the electric motor directed to the cutting band driving wheel is transmitted by a motor with worm drive. The cutting band is tensioned on two cast iron wheels with a manual tightener and guided by adjustable rolling and linear set of carbide guides. A separate flood coolant container with an electropump is inside. The arm lowering speed (the cutting speed) is adjusted with a hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds to choose from: 36 and 72 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Cutting band saw dimensions 2455×27×0.9 mm Band tension mechanical (manual) Band speed Kjdpfx Asxn Itrearedw 36, 72 m/min Feed speed 0–50 m/min (stepless feed) Arm lowering control stepless – hydraulic cylinder Vice base height 900 mm Power supply 3-phase 400V Motor power 1.1 kW Weight 216 kg Warranty 12 months Manual yes CE declaration yes Angle 0º ø230 260×150 225×225 45º ø165 180×130 165×165 60º ø105 100×90 110×110 *Please note that machine is sold without CEE connector by default, since there are many different types of it. If you would like to receive it with the machine, please write it to the seller before making a purchase/during order proceeding. WARNING! THE MACHINE IS RETURNED, SERVICED, NO PACKAGING.

Condition: new, Year of construction: 2025, SELF-CENTERING PLANER OSI proudly presents the European version of its self-centering planer (SCP-450). For over 20 years, OSI Machinery has supplied this technology to the North American wood industry (Canada, United States). The OSI Machinerie Self-Centering Planer (SCP) optimally utilizes every single board, regardless of defects (bowed, twisted, warped, cracked), significantly increasing yield. The SCP-450 ensures 100% thickness accuracy for all processed elements. Ksdpfxsww I Iqs Aaredw It planes the same thickness on both sides of the material. Independent suspension guarantees optimal calibration, enabling precise planing at all times. This patented solution eliminates jams and downtime. The SCP-450 is applicable in a wide range of production environments: • Hardwood lumber • Furniture • Doors and windows • Components • Cabinets • Calibration FEATURES: High yield (maximum material utilization) Opposing horizontal cutterheads Self-centering segmented feed and pressure rollers Minimized snipe and missed planing spots Attainment of maximum possible surface area Thickness accuracy guaranteed to +/- 0.076 mm Elimination of burn marks and depressions Digital thickness readouts Spiral planing heads with replaceable knives Hydro-lock collars on each 76 mm column (4) Maximum feed speed: 50 m/min Board width: 450 mm Board thickness: 4 mm to 130 mm Material removal up to 6 mm (per side) Minimum board length: 600 mm Power to planer heads: 2 x 45 kW Spiral heads: 10 spirals (5+5) Planer head diameter: 150 mm with replaceable 4-sided knives, 15 mm x 15 mm x 2.5 mm Segmented fingers: 32 mm carbide segment fingers function as pressure and anti-kickback devices Segmented roller drive power: 4 x 2.25 kW Infeed segmented rollers: 2 x top Outfeed segmented rollers: 2 x bottom Hydro-lock clamping system Voltage: 380 V

Condition: like new (used), mileage: 94,000 km, power: 102.97 kW (140.00 HP), fuel type: diesel, emission class: euro6, Year of construction: 2022, FIAT DUCATO 35 MAXI YEAR 2022, 2200MJT engine with 140 HP, L3H2, total length 6 meters, 94,000 km, reversing camera, air conditioning, multifunction steering wheel, regularly serviced, single owner, payload 1,350 kg, financing available, 1-year warranty. Contact: Benito 3383844139 Michele 3394588233 Kjdpfx Ajwx Iw Uoarjdw