Thread-Cutting Machine

METALLKRAFT GS 1200-36 E inkl. Unterbau

Condition: good (used), Year of construction: 2008, turning length: 2,000 mm, feed rate X-axis: 3,000 m/min, feed rate Z-axis: 3,000 m/min, HeidenHain ND780 3 Axis dro Variomatic RPM speedrange  Steady rest Multi fix Tool system DBC Turning Length: 2000mm Swing over bed Ø: 830mm Swing over cross slide Ø:420mm Swing in the gap Ø: 1000mm Gap length: 295mm Spindle bore: 110mm Bed width: 560mm Tailstock spindle Ø: 105Ø Stroke pinole: 225mm Spindle taper: 6Mk Power: 15kW Speeds / ranges: 2000Rpm Feed rate X-Axis: 3000mm/min. Feed rate Z-Axis: 3000mm/min. Workpiece load: 2400 Length: 3700mm Width: 1900mm Godpfxjxf Ey Rj Abhobi Height: 1900mm Weight: 5500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Tool presetter EZSET EZ400 Gsdpfxouhb Sts Abhsbi

Year of construction: 2009, condition: good (used), Load capacity: 30 t Gbedpfxoqiz N Ro Abhji Fine lift Lifting height 9 meters

Condition: new, Year of construction: 2023, Highly efficient series production Clamp – enter the cutting dimension – start. Automatic saws with loading are a standard of rational series processing of bar and bundle material. Cutting area max. up to 290 x 320 mm. Furnishing Automatic hydraulic sawing machine with NC control for cutting from 0° to 60° right, complying with all CE safety standards The device has 9 programs, each of which composed of 99 individual steps, with a total number of approx. 890 cutting positions, with corresponding piece counter Function: material feed closing fixed vice Blade rotation, distribution of emulsifiable liquid, temple lowering until the end of the cut and return of the feed carriage until specified amount bail return and stop the blade rotation by cooling liquid distribution cycle repetition Gbedjfww Sqspfx Abhsi Hydraulic feed cut by cut with no length limit Numerical control of quantity and length of cut Hydraulic control center with cutting pressure adjustment The saw blade is tensioned electro-mechanically by means of Microswitch monitored. Device with brush for belt cleaning Bimetallic strip 3200 x 27 x 0.9 mm Section thickness 1.2 mm Material feed stroke 600 mm Motor hydraulic center 0.75 kW Electric pump 0.09 kW to cool the belt It is always possible for you to inspect the desired system in our production/demonstration hall. Please do not hesitate to contact us.

Condition: new, Metal Deburring and Edge Rounding Machine (Double Side). DM1100 2C, edge rounds top and bottom sides of metal parts in one single pass. This double sided operation machine deburrs metal sheets rounding its internal and external contours. Featuring 2 sets of double cross belts this machine removes sharp edges on stainless steel, steel and aluminum parts cut by laser, punching or shearing. This metal deburring machine can easily edge round parts with small dimensions, being capable of deburring different shapes and parts sizes from 50mm up to 1100mm. Processes simultaneously both sides of metal sheet parts cut by laser or punching machine, saving time and reducing operation costs. Additional conveyor belt and support table enables single side edge rounding of metal parts down to 50x50mm. DM1100 2C can edge round metal parts with plastic foil, keeping the original finishing and assuring the work purely on the edges. Easy and tool free cross belt replacement. Program for automatic positioning of upper and lower cross belts in order to improve the access, reducing replacement procedure time. High performance on all edges and also on internal holes. Easy to use with an integrated touch screen for monitoring the working settings and the machine alarms. Technical Details: Working capacity (mm) 1100x50 No. Cross belt stations 2 Gbjdpfxsd Ev Ups Abhji Cross belt speed (m/s) 2-8 Feeding speed (m/m) 0.6-3.2 Cross Belt Motor (kW) (4x) 3 Feeding motor (kW) (3x) 0.18 Total power (kw) 13.1 Consumption (A) 30 Dust extraction connection (Ø mm) 150 Dimensions (mm) 2560x1980x2150 Weight (kg) 2210

Condition: new, functionality: fully functional, Comparable to Durma, Baykal, Ermaksan, etc. Bending length 3020 mm Pressing force 220 t Approach speed 140 mm/s Bending speed max. 10 mm/s Return speed 130 mm/s Stroke 350 mm Installation height 600 mm Throat depth 450 mm X-axis travel 750 mm X-axis speed 300 mm/s R-axis travel 250 mm R-axis speed 100 mm/s Clear gap between frames 2555 mm Machine length 3730 mm Machine width 2290 mm Overall height 3055 mm Table height 820 mm Motor power 22 kW Oil tank 300 l Machine weight 11,500 kg (technical data may vary depending on equipment) Standard equipment: - 3 CNC axes (Y1, Y2, X) - Press beam double-guided, stable and precise - Robust backgauge, double-guided - Manual backgauge fingers, double-guided on linear rails - Movable front arms with height adjustment - Side and rear safety guards - Lower die adapter rail 60 mm - Manual upper tool clamping system (Promecam system) - Manual crowning - Foot switch with emergency stop - 380 V, 50-60 Hz, 3 phase - LED lighting Including the following options: - Delem DA 66T CNC controller - Fiessler AKAS 2M laser finger protection - FPSC Safety PLC (manual) - X-R axis with servo motors - CNC crowning for high bending accuracy - 2 additional backgauge fingers - Further bending lengths and capacities available with appropriate accessories! - Godeq D Dzlepfx Abhobi

Condition: used, Year of construction: 1981, machine/vehicle number: 9, Anpapp-Presse und Falzeinbrennmaschine Schmedt PräForm HHS 20 Case Press and Joint-Setting machine Schmedt PräForm HHS 20 Baujahr / Year 02/1981 - Serial-Nr. 09 Buchhöhe / Book height: 100 - 520mm Gbodermul Djpfx Abhei Buchbreite / Block width: 120 - 400mm Blockstärke / Block tickness:: 8 - 100mm Leistung / Output: ca. 150 St/h Pressluftanschluss / Air supply: 6bar Elektrischer Anschluss / Power supply: 230V / 50Hz / 2.0kW Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: good (used), Technical data: Working length: 2050 mm Max. bending capacity: 18.0 mm Pre-bending: 12.0 mm Top roller diameter: 280 mm Bottom roller diameter: 280 mm Conical bending device Gbsdpfx Abexruvzjhsi Hydraulic drop-end bearing Motor power: 7.5 kW Dimensions (length x width x height): approx. 3650 x 1550 x 1650 mm Weight: approx. 7.5 tonnes The seller is not liable for typing or data transmission errors. The machine's condition in appearance, technology, and wear corresponds to its age; used machines are sold without any guarantee.

Condition: used, Year of construction: 1998, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 550 mm, rotational speed (max.): 12,000 rpm, overall weight: 7,500 kg, For sale: CNC 5-Axis Machining Centre, manufacturer DMG, model DMU 60 P The machine is fully operational and ready for immediate use. In 2021, a new spindle was installed, and all required maintenance has been carried out. History: 2019: New ball screw (KGT) 2021: New spindle 2022: Single-shift operation 2023: Occasional job orders 2024: Taken out of operation but remained connected to power 12/2025: Dismantled, cleaned, and stored Technical Specifications: X travel: 600 mm y travel: 650 mm z travel: 550 mm Control unit: Heidenhain TNC 426 Spindle speed: max. 12,000 rpm Spindle drive power: 15 kW Max. torque: 130 Nm Tool holder: SK 40 Table diameter: 630 mm Max. table load: 500 kg Number of tool pockets: 60 positions Max. tool length: 350 mm Rapid traverse (X/Y/Z): 24 m/min Feed rate: 20 - 10,000 mm/min Total connected load: 44 kVA Space requirements: approx. 7.0 x 6.0 x 2.7 m Machine weight: approx. 7.5 t Please note: Vices or clamping fixtures are not included in this offer. Gbodpfx Abswbhq Hshoi Upon request, we can organise transport and loading, at an additional cost. Europe-wide service available. All prices are subject to VAT. Inspection is possible by appointment. Please contact us—our team is happy to assist you. Trade-in or exchange possible! Machinery Purchase / Sales PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MORE. Are you looking for a high-quality yet affordable metalworking machine for your manufacturing needs? Or are you looking to sell yours? For more information or contact options, please visit our website.

Condition: excellent (used), functionality: fully functional, Year of construction: 2019, operating hours: 634 h, control type: CNC control, controller model: CN DELEM T3500T, bending force (max.): 100 t, working width: 3,060 mm, stroke length: 350 mm, distance between stands: 3,384 mm, installation height: 500 mm, type of crowning: CNC-controlled, TRUMPF TRUBEND 3100 Press Brake (X) Version with Increased Clearance to 500 mm Only 634 hours powered on! Protective laser CNC crowning table DELEM T3500T CNC control CNC axes: Y1/Y2/X/X2/R/Z1/Z2 Year: 2019 Currently tooled for a bending length of 2550 mm 1 die (V6 mm) with a length of 2550 mm included as additional equipment. MACHINE NOT ANCHORED TO FLOOR Specifications Bending length: 3060 mm Capacity: 100 tons Frame gap: 3384 mm Ram stroke: 350 mm Motorized backgauge travel: 560 mm Distance table-to-ram: 500 mm Main drive power: 24 KVA Gbjdpfsx E Ag Dsx Abhoi Weight: 8,300 kg Machine dimensions (L x W x H): 3,607 x 1,644 x 2,800 mm