Deep hole drilling Mollart LD8 150Pellet

Mollart LD8 150 Pellet Die

Condition: used, Year of construction: 1961, max. workpiece diameter 100 mm Lsdpfx Abowwl I Is Ujrt min. workpiece diameter 10 mm workpiece length 1000 mm total power requirement 16 kW weight of the machine ca. 3 t dimensions of the machine ca. 0 m The guides have been outdated 10 years ago

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Ljdpfxjuz If No Ab Uort Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Year of construction: 2005, turning diameter 275 mm Ledpfxew E Nnbe Ab Uort turning length 900 mm control TRAUB TX8i spindle passage 65 mm power capacity at 100 % load 25,20 kW power capacity at 40 % load 30,20 KW max. torque at 40% / 100% load 180 / 135 Nm spindle turning speed - stepless 1 - 5.000 U/min spindle diameter in front bearing 110 mm C-axis 1 - 500 U/min worktool support No. 1 x-axis 290 mm y-axis 165 mm z-axis 600/950 mm B - axis 360 ° rapid traverse X/Y/Z 18 / 18 / 30 m/min feed capacity X/Y/Z 10 / 10 / 7 kN number of tools 2x2 + 2x2 number of driven tools 2x2 + 2x2 mm toolpiece turning speed range 8.000 / 2.000 U/min power capacity at 25 % load 5,80 kW max. torque at 25% load 4x18,6 / 4x74 Nm tool taper TRAUB Ø60 worktool support No.2 / No.3 / No.4 x-axis 170 mm z-axis 600/950 mm y-axis +/- 60 mm rapid traverse X/Y/Z 18 / 15 / 30 m/min feed capacity X/Y/Z 10 / 10 / 7 kN tool turret - number of stations 10 number of driven tools 10 mm toolpiece turning speed range 1 - 6.000 U/min power capacity at 25 % load 5,80 kW max. torque at 25% load 18,60 Nm tool taper DIN 69880 Ø40x63 bar loader DNH61 / 3000 Bar length 1.000 - 3.200 mm bar material dia. 18 - 63 mm hexagon max.45 mm total power requirement 95,00 kW weight of the machine ca. 16,00 t dimensions of the machine ca. 10,00 x 3,50 x H3,00 m With TRAUB TX 8i control unit, main and counter spindle with C-axis, 3 turrets, 1 vertical-tool-carrier with B-axis, dust exhauster, chip conveyor, coolant system with coalescence-separator. Barfeeder TRAUB Stamag DNH61 /3000 2 pc. 3-jaw chuck SMW KNCS-N 170-43 2 pc. HAINBUCH Spanntop chuck 40 pc. various tool holder non-driven 6 pc various tool holder driven Spare parts package Machine can be inspected under power.

Year of construction: 1995, condition: used, machine/vehicle number: 18891, Force: 10 to. Stroke: 1000mm 3 Broaching-stations Lodpfxjbrcmke Ab Ujrt With chip-conveyor + platform and safety door

Condition: good (used), Year of construction: 2008, functionality: fully functional, Production line manufactured by a Canadian company Brunette, which can be described as very powerful and durable. Lrodpjvu D Dwofx Ab Uot The offer includes a log debarker with feeding tables, bark collection conveyors, as well as a chipper with 630kW installed capacity and a double screw unloading conveyor.

Condition: excellent (used), Year of construction: 2001, operating hours: 4,500 h, functionality: unexamined, machine/vehicle number: 090119, Manufacturing origin CE - Germany Voltage 400V Netweight 7500 kg Custom position 8458.91 20 Dimensions 2,9 x 2,3 x 2,3 m. 29731 hrs - work 4500h rs TECHNICAL DATA AXES Maximum travel X-axis 400 mm Maximum travel Y-axis 300 mm Maximum travel Z1-axis 475 mm Maximum travel Z2-axis 475 mm Relative positions B-axis 0,0001 – 360° Relative Position C1/C2-axis 0,0001 – 360° WORKPIECE Maximum cubic dimensions 80x80x80 mm Maximum weight 5 kg TURRET Number of stations 24 Number of controlled stations 18 Number of steady stations 6 Maximum tool attachment (round) Ø 20 mm Maximum tool attachment (square) 16x16 mm (20x20) Maximum trajectory of turret above tool’s point 500 mm Rotation speed of live tools 1-9000 min-1 SPINDLE Maximum rotation speed 6000 min-1 Maximum bars diameter Ø 42 mm Maximum forced chuck clamping 140 mm BARS MACHINING Maximum bar length for bar’s feed 1000 mm Maximum piece size for the bar taker Ø42 x Long.100 mm Maximum diameter of taker’s collets 42 mm Pulling and pressure force of clamping cylinder 20000N FEEDS X-axis advance force abt.895 daN Y-axis advance force abt.895 daN Z1-axis advance force abt.895 daN Z2-axis advance force abt.895 daN Fast moves axes X/Y/Z 20 m/min Motor’s torque of tool control 2,4 Nm Spindle S1 / Spindle S2 70Nm COOLING (values only as indication) Capacity of pump submerged inside chips conveyor 10 l/min for abt. 4,5 bar 80 l/min 3,2 bar 150 l/min 0,7 bar Capacity of overpressure pump inside conveyor 10 l/min 13,2 bar 50 l/min 9 bar 90 l/min 1 bar Lubricating coolant volume inside conveyor abt.134 L. Coolant volume inside cooling aggregate 45 L. NUMERIC CONTROL Siemens 840D MACHINING PRECISION Resolution axes X/Y/Z 0,1 µm Resolution axe B 0,0001° Resolution axe C 0,0001° Positioning precision 5 µm Repeatability 0,6 µm Maximum error on workpiece’s concentricity 0,5 µm ELECTRIC Spindle 1 / Spindle 2 (at 100%) 11 kW Spindle 1 / Spindle 2 (at 40 %) 15 kW Advance motors axes X/Y/Z1/Z2 1,3 kW Axis B 1,3 kW Tool control 2,3 kW Hydraulic pump 7,5 kW Hydraulic back movement 0,75 kW Cooling aggregate fan 1 / 2 0,18 kW Circulation pump of cooling aggregate 1,1 kW Compressor of cooling aggregate 2,2 kW Chips ejector 0,25 kW Emulsion pump 1 1,1 kW Emulsion pump 2 2,2 kW Operation tension 400 V Network frequency 50Hz (60option) Control tension 24V DC Absorbed power 35 kW Nominal current 63A Connecting réseau TM / TT / IT Lrjdpfx Ajht Hg Dsb Ust PNEUMATIC Maximum operation pressure 10 bar Normal operation pressure 6 bar Minimal operation pressure 5 bar Air output env. 150 L/min Valves tension 24V DC Oil-mist lubrication tank capacity 12 L Quality level 2 selon Pneurop6611 NOISE LEVEL Normal use 78—80 dB errors and omissions excepted-data given without obligation Inventory no.2321018, machine equipped with : Chip conveyor Preparation for bar feeder Tool holders : 6 fixed drills ER32 8 turning tool holders 5 live tool holders ER32 4 live tool holders ER25 6 live tool holders ER20

Condition: good (used), drilling depth: 1,500 mm, feed length X-axis: 2,000 mm, feed length Y-axis: 1,300 mm, feed length Z-axis: 1,500 mm, Manufacturer: TBT deep drilling technology Type: BW 250-S Control: SIEMENS 840D Year of manufacture: 2007 Drilling, Milling, Tapping for heat exchanger bases and plates Swivable A Axis + 25 to - 15 Degrees Filtration and Coolant system 1000 L Cip conveyor 2000 x 1200 height out put Milling tool changer Tower Station 20 positions Capacity ELB Drilling 3 - 35 mm Capacity Milling 250 ccm/Min Feed rates all axis 15,000 mm/Min X-Y-W-Z Cutting hours approx. 15,000 Large tooling package Specifications Metric US Standard Max. Drill Ø steel 40 mm Drilling depth 1500 mm X - axis 2000 mm Y - Axis 1300 mm Z-axis 1500 mm W-axis 750 mm Table load 15000 Table dimensions / L x W or ø 1600 x 1200 mm Spindle mount HSK 63 Mk Spindle power 11 kW Speed 8000 Rpm Dimensions (estimate) Length 7200 mm Width 7800 mm Height 4250 mm Weight Ledpfx Abov A Uw Do Usrt 23000 kg Please note: The information on this page is believed to be accurate and is provided by us and, where possible, from the manufacturer. The information is provided in good faith but accuracy cannot be guaranteed. Accordingly, it will not constitute a representation or contractual terms. We recommend that you check all important details.

Condition: used, centre distance 2.500 mm centre height 250 mm grinding wheel diameter 600 mm Total travel of the grinding support 320 mm spindle speeds 50 - 450 mm tool adaptor MK5 tail stock MK Cylindrical Grinding Machine | NAXOS-UNION - W-500 Lredpfx Asx Avtcsb Uet the cylindrical grinding machine was overhauled in 2017 by KPS-Schleiftechnik (RETROFIT – see order confirmation). The machine is in a well-maintained condition. Please refer to further technical details in the attachement of the offer. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: W-500-2500 | W500 | W 500 | W 500 2500

Condition: good (used), Year of construction: 2002, workpiece dia. 40 mm max. module 2 min. module 0,1 workpiece length - max. 665 mm weight 4,5 t spindle bore diameter 30 mm Control Siemens dia. of cutter bearing 20 mm total power requirement 5,5 kW Technical data max. module 2 Pitch 0.5 - 25 mm Number of speeds multi-speed / multiple max. workpiece diameter40 mm max. workpiece length180 mm Milling cutter diameter max.80 mm max. milling cutter width12 mm Z-axis (milling length with counter point)90 mm Z-axis (milling length without counter point)113 mm Milling head swivelling angle30° / 30° Lodpjv Ucdvefx Ab Usrt Description Gear hobbing and thread cutting machine. LAMBERT - 124 CNC The machine is in a well-maintained condition.

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: 17004A, bar diameter (max.): 20 mm, For sale: two fully operational Tsugami HS20M 5-axis machines. Everything is in working condition, recently serviced and technically inspected. Lrodpfxsyghcrs Ab Uet Included: various tool holders, full technical documentation. These machines were primarily used for manufacturing dental implants and were sourced from Sweden. If interested, please contact me for further details, photos, pricing, or to arrange an inspection.