Used Curve Cut for sale (14,848)

Condition: excellent (used), functionality: fully functional, Year of construction: 2016, Laser Machine Prima Power CV 5000 Year of manufacture: 2016 3.1. CV SERIES CO₂ LASER SPECIFICATIONS (CV 5000) Average power: 200 W – 5000 W Peak power: Up to 6 kW Lsdpfxeywwq Ue Abceri Wavelength: 10.6 micrometers Beam quality factor (M²): < 2.4 (typically 2.1 to 2.3) Beam divergence: 1.5 mrad (half-angle) Output beam diameter: 15 mm 1/e², 21 mm full beam Pulsed operation – pulse repetition rate: 0 – 2 kHz Pulse width: 250 microseconds, 70 µs resolution Alignment stability: +/- 150 µrad Operating conditions: • Ambient temperature (max): 40 °C • Ambient temperature (min): 10 °C • Relative humidity: < 95% (non-condensing) Diode laser: • Wavelength: 635 nm • Output power: < 1 mW — 3.2. CV SERIES CO₂ LASER SUPPLY SPECIFICATIONS (CV 5000) Electrical: • Power consumption: 37 kW • Voltage: 400 VAC – 460 VAC ±10%, 3-phase Cooling: • Required cooling capacity: 45 kW • Flow rate: 133 L/min (35 GPM) • Inlet temperature: 18 – 20 °C • Maximum inlet pressure: 6 bar • Nominal inlet pressure: 3 bar • Differential pressure: 1.5 bar • Coolant: Distilled water with 35% Dowfrost HD • Filtration requirement: 100 micron Gas: • Type / Purity / Gas mixture / Consumption: • He: 99.996% | 67.7% | 13.4 – 46.8 SLPH • CO₂: 99.995% | 4.1% | 0.9 – 3.0 SLPH • N₂: 99.996% | 28.2% | 5.8 – 20.2 SLPH • Total consumption: 20 – 70 SLPH (variable) Additional requirements: • < 10 ppm water vapor, hydrocarbons, and oxygen • Air: dry – dew point < 2 °C • Depending on shutter usage

Condition: used, power: 160 kW (217.54 HP), Granulator DREHER 26/90 / Granulators The machine is equipped with precision-ground blades and is suitable as a granulator for punching grids and film webs. Lrodsywutyjpfx Abcoi Machine data: Drive: 7.5 kW Rotor blades: 5x3 Stator blades: 2x2 Rotor diameter: 260 mm Rotor width: 900 mm With roll feed

Condition: used, power: 160 kW (217.54 HP), Granulator DREHER 26/90 / Granulators The machine is equipped with precision-ground blades and is suitable as a granulator for punching grids and film webs. Lrodpfxoywurio Abcoi Machine data: Drive: 7.5 kW Rotor blades: 5x3 Stator blades: 2x2 Rotor diameter: 260 mm Rotor width: 900 mm With roll feed

Year of construction: 2017, condition: ready for operation (used), - USED - FIBER LASER CUTTING MACHINE FOR TUBES WITH LOADING/UNLOADING SYSTEM MIN CIRCULAR SECTION: ø 25 mm MAX CIRCULAR SECTION: ø 355 mm MAX SQUARE SECTION: 260 X 260 mm MAX RECTANGULAR SECTION: 300 X 200 mm MAX ADMITTED LOAD: 100 Kg/m SOURCE: IPG YLS-4000 ; 4000 W CONTROL UNIT: SIEMENS 840D WEIGHT: 12500 Kg Lodex E Eihepfx Abcsri NOTE: AUTOMATIC LOADING 3-12.5 mt; AUTOMATIC UNLOADING 12.5 mt; 3D CUTTING HEAD; CAPACITIVE SENSOR; AUTOMATIC ADJUSTMENT

Condition: refurbished (used), Year of construction: 2018, functionality: fully functional, High-precision wire EDM machine GF CUT 1000 Year of manufacture: 2018 Travel ranges (X/Y/Z): 220 x 160 x 100 mm Ljdpfjywkt Nsx Abcsri Travel range (U/V): +/- 40 mm Max. taper: 3° at 80 mm height Wire diameter from 0.05 mm to 0.20 mm Best achievable surface finish: Ra=0.08 µm Max. workpiece dimensions: 300 x 200 x 80 mm Max. workpiece weight: 35 kg Including AGIEJOGGER handbox for convenient machine setup 15" LCD color display with integrated keyboard and mouse AGIEVISION CNC control Including AGIESETUP 3D Including AGIEDUO dual-wire system for automatic changeover between two wire diameters Machine dimensions: 1400 mm x 1900 mm x 1970 mm Machine weight: 2700 kg The machine is cleaned, factory overhauled, and thoroughly tested by our specialists. We are happy to commission the machine at your site and provide training in the control system and machine operation.

Year of construction: 1985, condition: used, machine/vehicle number: 60802 A 17983 J, cutting circuit: bis 400 A space needed: 820 x 1220 x 930 mm weight: 750 kg Lrjdpo Sdrfsfx Abcoi

Year of construction: 2012, operating hours: 14,534 h, condition: ready for operation (used), General Data Machine weight 13000 kg Control Unit Brand BYSTRONIC Model ByVision Cutting Main Drive Laser power 3000 W Table Table load 750 kg This Bystronic Bysprint Fiber 3015 3kW was manufactured in 2012. It features a max laser power of 3,000 W and handles sheet sizes up to 3000 × 1500 mm. It supports a max cutting thickness of 20 mm for steel and 12 mm for stainless steel and aluminium. If you are looking to get high-quality cutting capabilities, consider the Bystronic Bysprint Fiber 3015 3kW machine we have for sale. Contact us for more information about this machine. Application Types Cutting Lredpfx Aex D R Ttebcei

Condition: ready for operation (used), Year of construction: 2014, operating hours: 32,457 h, Control Unit Brand BYSTRONIC Model na This Bystronic ByAutonom 3015 was manufactured in 2014. A robust CO2 laser cutting machine from Switzerland, it features a 6kW laser power and can handle steel up to 25mm thick. With a maximum positioning speed of 169m/min and a quick table changeover time of 22s, it's designed for efficiency. Consider the opportunity to buy this Bystronic ByAutonom 3015 CO2 laser cutting machine. Contact us for more information about this machine. Application Types Cutting Lsdpfx Aex D S Ewebcsri

Condition: ready for operation (used), Year of construction: 2008, General Data Measurements width 4100 mm Measurements depth 10169 mm Machine weight 5500 kg Control Unit Brand MicroStep Model IMSNC Main Drive Number of axis 3 This 3-axis MicroStep PLS 7501.25PG plasma cutting machine was manufactured in 2008. It features a robust MicroStep MSNC500 control system and dual cutting capabilities with a HPR 260 AGC plasma and an acetylene gas burner. The machine offers a maximum cutting thickness of 50 mm and operates efficiently within a large working field. If you are looking to get high-quality cutting capabilities, consider the MicroStep PLS 7501.25PG machine we have for sale. Contact us for more information. Application Types Lredpfx Abox D Ey Iecji Cutting

Condition: good (used), Curved roller conveyor, curved track, curved roller conveyor, curved roller conveyor, curved roller conveyor, roller curve, curved conveyor with drive, roller track, roller curve conveyor, roller track, conveyor track -Manufacturer: Soco, roller curve conveyor with drive, height adjustable -Rollers: Ø 54-80 x 355 mm -Speed: 14 m/min -Drive: 2x 0.12 kW, see photo of nameplate -Transport dimensions: 1500/600/H840 mm -Weight: 64 kg Lrsdpfxsywu Azo Abcoi

Condition: used, Year of construction: 2013, Type Crack Maschine In our opinion, the machine is in good used condition and can be inspected under power by appointment. Accessories, tools, and clamping devices shown are only included in the scope of delivery if noted in the additional information. Subject to changes and errors in the technical data and information, as well as subject to prior sale! Ledpfex N Nc Hjx Abcjri

Condition: used, Year of construction: 1989, Diameter max. 75 mm Dimensions (L/W/H) 800x600x1200 mm weight ca. 150 kg In our opinion, the machine is in good used condition and can be inspected under power by appointment. Accessories, tools, and clamping devices shown are only included in the scope of delivery if noted in the additional information. Lodjxrg D Rspfx Abcjri Subject to changes and errors in the technical data and information, as well as subject to prior sale!

Condition: ready for operation (used), Year of construction: 2015, - USED - FIBER LASER CUTTING MACHINE WITH PALLET CHANGER and LOADING/UNLOADING SYSTEM X-AXIS TRAVEL: 4000 mm Y-AXIS TRAVEL: 2000 mm Z-AXIS TRAVEL: 115 mm RAPID FEEDS X-Y-Z: 245 m/min WORKING AREA: 4000 x 2000 mm ADMITTED LOAD ON TABLE: 1250 Kg Lodpfxexqtx Sj Abcsri SOURCE: TRUDISK 5001 ; 5000 W WEIGHT: 15000 Kg OVERALL DIMENSIONS: 10900 x 5700 x 2400 mm NOTE: LIFT MASTER COMPACT LOADING/UNLOADING SYSTEM

Condition: ready for operation (used), Year of construction: 2017, General Data Machine weight 9000 kg Measurements height 2300 mm Measurements depth 4300 mm Lredpfx Absx D It Rscei Movement X-Axis Movement 3000 mm Y-Axis Movement 1200 mm Main Drive Number of axis 3 Dimensions Machine Length 15000 mm This 3-axis Hypertherm PL-YPE 3100 was manufactured in 2017 and features a Hypertherm® HyPerformance HPR 400XD gas plasma source. It offers precise cutting with a maximum capacity of 50 mm in mild steel, 75 mm in stainless steel, and 45 mm in aluminum. The effective cutting area is 3000 mm by 1200 mm. If you are looking to get high-quality cutting capabilities, consider the Hypertherm PL-YPE 3100 machine we have for sale. Contact us for more information. Application Types Cutting

Condition: ready for operation (used), Year of construction: 2015, This KOIKE PNC-12 EXTREME plasma cutting machine was manufactured in 2015. It features a robust CNC control system and an effective cutting area of 1500 x 3000 mm. Capable of handling a maximum cutting thickness of 50 mm and equipped with rapid travel speeds up to 4000 mm/min, it ensures efficient operation. Consider the opportunity to buy this KOIKE PNC-12 EXTREME plasma cutting machine. Contact us for more information about this machine. Application Types Cutting Lsdpfox D Nhvsx Abcsri

Condition: excellent (used), C.N.C. WORKING CENTER 4 axes (X-Y-Z-C) Goose-neck type, with Numerical Control ICOS-Open. Software IMAWOP / IMATRONIC - BIMA Fast Cut Working table with pods and rails. No. 8 Supports (rails) of length mm 1400 Automatic deplacement by CNC (X axis) of the Supports/rails Automatic deplacement by CNC (Y axis) of the vacuum pods/cups Ljdpjvxhnusfx Abcsri Automatic Tools Changing System. Tools storage plate (No. 18 folds- positions) Max. useful working area (X - Y - Z) mm 4200 x 1600 x 60 Min. workpieces dimensions (X - Y - Z) mm 295 x 115 x 14 Max. workpieces dimensions (X - Y - Z) mm 4250 x 2200 x 60 Motorized carpet to evacuate chips and wastes Separate electric and command cabinet. Total installed power (Kw) 28 WORKING GROUPS (TOP): Vertical electro-spindle 1 x HSK F63 - electro-spindle motor power Kw 14,5 (S6) / Kw 7,5 (S1) N° 3 Clamps to fix the panel and move it on to the machine (on top of the vacuum pods) N° 5 Air cushion tables (for the panel parking before being processed) Vacuum system with suction cups (controlled by CN) to lift panel onto outfeed belts Workpieces Outfeed system (from Bima Cut) with system with motorized belts

Condition: used, • Model – Genius 37 CT-S • Year of manufacture – 2007, serial number: 86592 • Max. glass size: 3300 x 2550 mm • Glass thickness: 3 – 19 mm • Can also cut shapes, offcut optimization, data input at the cutting table • With breaking bars and strong air cushions • Table can also tilt • Working height: 900 mm • Weight: 2600 kg Lrjdpfx Aowz U Hbsbcsi

Condition: used, • Type – 490P/LFB/1Q+14 No. 2020/6450 • Semi-automatic for split strips • Cutting head can be automatically switched between longitudinal and cross-cutting • Digital display for longitudinal and cross-cutting • Cross-cutting drive: Automatic Lrodpfx Aewcz Riebcoi • Longitudinal cutting by pulling the cutting bridge over the cutting table • Complete table is pneumatically tiltable • Air cushions • Breaking bars • Working height approx. 900 mm • Table length – 3800 mm, width – 2500 mm • Width with cutting bridge 2800 mm • Year of manufacture approx. 2020 • Price upon request

Condition: excellent (used), machine/vehicle number: 02 P 0587, cutting circuit: 15 - 40 A electrical connection: 230 V, 16 A kW space needed: 470 x 250 x 250 mm Ledpfx Aedyy Diobcsri weight: 10 kg

Condition: ready for operation (used), machine/vehicle number: 30116, Arc current at 100% ED: 120 A Voltage: 110V Lsdpfx Aboga Tmyoceri electr. Connection for: 380 or 400 V Required space: 1250 x 900 x 1000 mm

Year of construction: 1965, condition: used, machine/vehicle number: 2383, for tube-Ø: 250 - 530 mm for material thickness: 3 - 40 mm drive: by hand Ledpfx Asb Nv Stsbcori space requirement: 1000 x 800 x 1200 mm Weight: approx. 70 kg

Condition: good (used), machine/vehicle number: 19830704, for internal thread: M 2 - M 5 Spindle mount: MK 1 Lrsdpfx Absfny Apecoi Overall length: 240 mm

Condition: ready for operation (used), Year of construction: 1989, Saw blade Ø: 350 mm Cutting capacity: at 90° & 45°, round: 120 mm at 90°, flat: 170 x 100 mm at 45°, flat: 120 x 100 mm at 90°, square: 100 mm at 45°, square: 95 mm 2 saw blade speeds: 17/34 rpm Ljdpjxln Ukefx Abcori Drive motor: 400 V, 2/2.6 kW Weight: 425 kg Required space: 900 x 800 x 1800 mm

Condition: good (used), Cutting range, internal thread: M 2 - M 12 Working radius approx.: 1650 mm Ljdpod D U T Hefx Abcsri

Condition: ready for operation (used), Year of construction: 2013, This MGM Omnicut 3100 was manufactured in 2013. A robust plasma cutting machine, it features a 12-meter table and a powerful Kjellberg HiFocus 360i plasma source. It efficiently handles mild steel up to 80 mm, stainless steel up to 80 mm, and aluminum up to 100 mm. If you are looking to get high-quality cutting capabilities, consider the MGM Omnicut 3100 machine we have for sale. Contact us for more information. Lrsdpex D Npaefx Abcei Application Types Cutting