Used Direction Switch for sale (9,774)

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2011, operating hours: 35,623 h, machine/vehicle number: A1225A0041 / L20, controller model: SINUMERIK 840D SL, laser power: 3,200 W, sheet thickness (max.): 20 mm, working length: 3,000 mm, working width: 1,500 mm, The machine was exclusively serviced by Trumpf until 2023 as part of a maintenance contract. TECHNICAL DETAILS Working length: 3,000 mm Working width: 1,500 mm Working height: 115 mm Travel range X-axis: 3,000 mm Travel range Y-axis: 1,500 mm Travel range Z-axis: 115 mm Maximum workpiece weight: 900 kg Sheet thickness steel max.: 20 mm Sheet thickness stainless steel max.: 12 mm Sheet thickness aluminum max.: 8 mm Sheet thickness max.: 20 mm Feed rate X-axis: 100 m/min Feed rate Y-axis: 200 m/min Feed rate Z-axis: 80 m/min Cutting speed: 140 mm/min Positioning speed X/Y-axis: 140 m/min Repeat accuracy: 0.05 mm Smallest programmable step: 0.001 mm MACHINE DETAILS Laser type: CO₂ laser Laser source manufacturer: Trumpf Laser source model: TruFlow 3200 Laser power: 3,200 W Laser wavelength: 10,600 nm Cooling type: Water Control type: CNC control Control manufacturer: Siemens Control model: SINUMERIK 840D SL Automation level: Semi-automatic Operating type: Electric Djdpfozyakgsx Aptokt Input voltage: 400 V Input current: 100 A Input frequency: 50 Hz Dimensions & Weight Dimensions (L x W x H): 6,500 x 7,600 x 2,200 mm Total weight: 12,000 kg Laser hours NC control: 35,623 h Laser hours resonator / pump 1: 34,258 h Laser hours beam on / pump 2: 10,155 h EQUIPMENT CE marking Central lubrication system Cooling unit Documentation / manual Dust extraction Emergency stop switch Safety light curtain

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, sheet thickness (max.): 3 mm, working length: 2,500 mm, TECHNICAL DETAILS Sheet thickness with tensile strength of 410 N/mm² max.: 2.00 mm Sheet thickness with tensile strength of 600 N/mm² max.: 1.25 mm Sheet thickness with tensile strength of 265 N/mm² max.: 3.00 mm Minimum sheet thickness: 0.50 mm Length of the notched plate at the inlet max.: 2,700 mm Width of the notched plate at the inlet max.: 1,500 mm Rotatable diagonal of the notched plate max.: 2,700 mm Bending length max.: 2,500 mm Clearance for bending above the work table max.: 127 mm MACHINE DETAILS Processor: Intel Pentium III, 500 MHz RAM: 128 MB SDRAM Graphics memory: 4 MB SGRAM Hard disk capacity: 9.1 GB CD-ROM drive: 600 MB Floppy disk drive: 3.5 inch, 1.44 MB Dkedpfx Aozv Rc Ssptot Network cards: 2 Screen diagonal: 17 inches Voltage: 400 V Frequency: 50 Hz Number of phases: 3 Rated power: 38 kW Rated current: 64 A Switching capacity of the main switch: 40 kA Further technical details can be found in the attached documents.

Condition: like new (used), Year of construction: 2022, controller model: Siemens Touch Panel KTP 600, bending angle (max.): 180 °, bending radius (max.): 200 mm, overall weight: 500 kg, power: 1.5 kW (2.04 HP), No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Bending direction: right Tube diameter steel: 4–28 × 3 mm Tube diameter non-ferrous metals: 4–35 × 2 mm Bending radius: max. 200 mm Bending height: 25 mm Bending speed: up to 45 °/s Effective bending angle: up to 180° + 10° overbending Switch-off accuracy: 0.1° Tube feed length: 1,500 mm MACHINE DETAILS Control: electronic Control model: Siemens Touch Panel KTP 600 Bending axis: electronically controlled Bending angle switching: automatic Program memory: 100 programs with 20 data sets each Target/actual value display for bending angle Tube clamping: hydraulic Clamping pressure: adjustable Slide block positioning: hydraulic Bending mandrel retraction: hydraulic Pump type: HD gear pump Pump capacity: 4.5 l/min Hydraulic pressure: 180 bar Bending head: free-standing Control panel: swiveling Machine design: mobile Maximum sound level: approx. 78 dB(A) Drive type: electro-hydraulic Drive power: 1.5 kW Mains voltage: 400 V Frequency: 50 Hz Phases: 3 Control voltage: 24 V DC Electrical standard: VDE Protection class: IP54 Dimensions & Weight Dimensions (L x W x H): 2,200 x 600 x 1,100 mm Weight: 475 kg EQUIPMENT Siemens Touch Panel KTP 600 Function keys with plain text display for operator guidance Automatic bending angle switching Target/actual value display for bending angle Swiveling control panel Free-standing bending head Hydraulic tube clamping with adjustable clamping pressure Hydraulic slide block positioning Hydraulic bending mandrel retraction Mobile machine design The height and weight of the asset must be considered when selecting the transport vehicle. Djdjzzlc Rspfx Aptjkt A forklift is available for loading. If the item is not collected on time, a storage fee of €20.00 per lot and commenced day will be charged. The fee must be paid before collection. The sale is made with the exclusion of any warranty or guarantee. The information on the technical data is based on the original offer. No guarantee is given for printing or measurement errors. If in doubt, please compare the information with the provided photos or inspect the goods on site before the end of the auction.

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: 17405, travel distance X-axis: 550 mm, travel distance Y-axis: 410 mm, travel distance Z-axis: 450 mm, workpiece weight (max.): 10,000 kg, spindle speed (max.): 15,000 rpm, number of slots in tool magazine: 240, No minimum price – guaranteed sale to the highest bidder! Bidding obligates the winner to pick up the machine between September 21st and October 1st! Dkodszqunhspfx Aptjt TECHNICAL DETAILS Travel range, X-axis: 550 mm Travel range, Y-axis: 410 mm Travel range, Z-axis: 450 mm Travel range, B-axis: -110 to +110° Travel range, C-axis: 360° Distance from pallet surface to spindle center: -20 to 430 mm Distance from B-axis center to spindle center: -40 to 410 mm Distance from B-axis center to spindle center: -20 mm Distance from pallet center to Z zero point: 265 mm Distance from pallet center to Y zero point: 180 mm Pallet Work area on the pallet: Ø 130 mm Pallet load capacity: 40 kg Max. workpiece size: Ø 250 × 250 mm Pallet mounting surface: 4 × M12 × 1.75 Distance from pallet bottom to pallet surface: 970 mm Pallet indexing, B/C-axis: 0.001° / 0.001° Pallet change time, B-axis: 1.2 s/90° Pallet change time, C-axis: 0.9 s/90° Pallet change time, C-axis: 1.2 s/180° Pallet change time, C-axis: 1.4 s/270° Pallet torque, B-axis: 1,070 Nm Pallet torque, C-axis: 192 Nm Pallet braking torque, B-axis: 1,112 Nm Pallet braking torque, C-axis: 500 Nm Spindle Spindle speed: 50 to 15,000 rpm Spindle speed change: 5-digit direct S-command Tool interface: SK 40 Spindle taper: 7/24, Taper No. 40 Spindle bearing inner diameter: 70 mm Max. spindle torque: 65.1 Nm at 1,100 min⁻¹ Spindle air blow: Standard Spindle orientation: Standard Tool clamping force: 7.0 kN Tool Changer Tool magazine capacity: 240 positions Tool shank: JIS B 6339, tool shank 40T Pull stud type: JIS B 6339, pull stud 40P Max. tool diameter: 80 mm Max. tool diameter with free auxiliary stations: 150 mm Max. tool length: 300 mm Max. tool weight: 10 kg Tool selection: Fixed address system Tool change arm: W-gripper type Feed Rates Rapid traverse rate, X/Y/Z-axis: 50 m/min Rapid traverse rate, B-axis: 30 min⁻¹ Rapid traverse rate, C-axis: 50 min⁻¹ Feed rate, X/Y/Z-axis: 1 to 50 m/min Feed rate, B-axis: 30 min⁻¹ Feed rate, C-axis: 50 min⁻¹ Rapid traverse acceleration, X/Y/Z-axis: 0.6 G Rapid traverse acceleration, B/C-axis: 2,500 / 2,000 °/s² Max. acceleration during cutting feed, X/Y/Z-axis: 0.4 G Max. acceleration during cutting feed, B/C-axis: 2,000 / 4,000 °/s² Tipping feed rate, X/Y/Z-axis: 0 to 4000 mm/min Tipping feed rate, B/C-axis: 0 to 11.11 min⁻¹ Min. movement increment, X/Y/Z-axis: 0.001 mm Min. movement increment, B/C-axis: 0.001° MACHINE DETAILS Control: MATSUURA G-TECH 840 DI Serial number: 350536 Electrical Connection Values Rated apparent power: 36 kVA Input voltage: 415 V Input frequency: 50 Hz Input current: 50 A Dimensions and Weight Overall length: 6,000 mm Overall width: 5,000 mm Overall height: 3,500 mm Overall weight: 15,000 kg EQUIPMENT - Chip conveyor - Coolant system - Tool holders on the tool changer External Reference: Hanon - Lot 1

Condition: used, Year of construction: 2004, operating hours: 28,082 h, travel distance X-axis: 800 mm, travel distance Y-axis: 620 mm, travel distance Z-axis: 520 mm, controller model: Siemens 840 D, spindle speed (max.): 13,000 rpm, The control unit (PCU 50) was replaced in March 2024! The machine spindle was replaced at approximately 5,500 operating hours! Tools are included in the offer! TECHNICAL DETAILS Travel range X-axis: 800 mm Travel range Y-axis: 620 mm Travel range Z-axis: 520 mm Spindle speed: 13,000 rpm Number of tool positions in the tool magazine: 30 MACHINE DETAILS Control unit: Siemens 840 D Operating hours Control unit operating hours: 60,150 h Machine operating hours: 56,860 h Spindle operating hours: 28,082 h Spindle replacement at: 5,500 h EQUIPMENT Tools 4th axis Hofmann RW/NC160 Oil mist extraction system Strip filter system with internal cooling 20 bar with double switching filter Documentation Hedelius + Siemens Sinumerik Dksdozvl Tfopfx Aptot Infrared probe Renishaw Note: The sale does not include the milling attachments on the rear panel of the machine. Since the machine has been demonstrated several times, the machine operating hours may vary slightly.

Condition: good (used), Motor protection switch, star-delta switch, reversing switch -Type: NNWYehb 15 Dodpfxjb A Sczs Aptjkt -Adjustment range in amperes: 1.3 - 2.0 -Price: per piece -Quantity: 10 pieces available -Weight: 0.8 kg

Condition: good (used), Year of construction: 2019, functionality: fully functional, workpiece height (max.): 60 mm, workpiece width (max.): 60 mm, workpiece length (max.): 150 mm, edge thickness (max.): 3 mm, height adjustment type: mechanical, feed rate X-axis: 18 m/min, actuation type: electric, total height: 1,468 mm, total length: 4,412 mm, total width: 1,511 mm, Very well-maintained and regularly serviced. TECHNICAL DETAILS Workpiece height: max. 60 mm Dksdpfxszv Rcre Aptjt Workpiece width: max. 60 mm Workpiece length: max. 150 mm Edge thickness: max. 3 mm Processable edge materials: ABS, PVC, veneer strip, solid edge strips Feed and Operation Feed rate X-axis: 18 m/min Height adjustment: mechanical Type of operation: electric MACHINE DETAILS Data recorded as of March 20, 2026 Main switch – total operating time: 9,720 h 57 min 06 s Chain drive – total operating time: 1,216 h 19 min 51 s Total number of workpieces: 91,356 pieces Total workpiece length: 63,904.7 m Overall height: 1,468 mm Overall length: 4,412 mm Overall width: 1,511 mm EQUIPMENT - Smartouch touchscreen control - Program settings with memory function - Release agent - Pre-milling unit - Radius cutter, top and bottom - Corner rounding unit - Radius trimming unit - Flat trimming unit - Adhesive remover - Polishing unit - Automatic feed

Condition: excellent (used), Year of construction: 2021, Semi & fully automatic pallet wrapping machine Manufacturer: Cousins Model: LPSWA-CE (“The Switch Semi2Auto”) Operating mode: Semi-automatic & fully automatic Year of manufacture: 2021/2022 Functions and specifications of the LP-SWA-SERIES Production speed: Up to 35 loads per hour. Load capacity: Maximum load weight: 4,500 lbs dynamic - 10,000 lbs static Maximum load size to safely pass the tower: 67“ x 67” (96“ load diagonal) x 80” H Maximum load size to stay inside the turntable: 46“ W x 46” L (65“ load diagonal) x 80” H Low profile turntable: 65” diameter, laser-cut steel top with all-around deck protection. Maintenance free 54-roller bearing support system. Turntable height 2.813 inches from floor. ANSI No. 50 direct chain drive with chain tensioner. Speed between 3 and 12 rpm with smooth start acceleration Film carriage elevator: 1/2 HP DC motor with variable speed ANSI No. 40, direct chain drive with shock absorber and fall protection Automation functions: Fully electric - no pneumatics required Cousins Smart Engineering has developed the A-Arm, an advanced cutting and holding device. It offers significant productivity gains and safety benefits. This technology is only available on Cousins machines. This unique method of applying and cutting stretch film offers you the following benefits: - Selectable banding function at the top - Stabilizes the load early in the wrapping cycle - Places the film end at the top of the load instead of the bottom - There is no film clamp on the turntable that can be damaged by dirt or operator error - and Also, no slip rings are required to power the turntable, reducing maintenance requirements - Load placement on the turntable is not critical - No air connections or noisy compressors - New automatic load detection safety feature on first rotation detects unevenly or partially stacked top layers and automatically adjusts the A-arm height to avoid obstructions - A-arm fall protection Control functions: Electronic control with LED user interface Wireless start/stop remote control with one transmitter (additional transmitters available) Power off - power on - reset switch and operation indicator Automatic wrapping cycle start/pause with just one button Cycle pause for applying the cover sheets Reinforce the wrapping control for the wrapping center Emergency stop button Turntable jog button Buttons for lowering and raising the film carriage Film tension control (force-to-load) Separate speed controls for raising and lowering the film carriage Variable speed control of the turntable Three-beam automatic load height detection sensor for dark or shiny loads Separate control for 1 to 12 turns top and bottom wrapping Selectable parameters for reduced film tension to wrap the top and/or bottom of the load Non-proprietary UL/CSA approved components A - B - C wrapping program selector with the option of entering and saving individual wrapping parameters for each program Product video 1 Product video 2 Product video 3 Dkedpswb A N Rofx Aptet Financing through our bank is also possible. komplett-konzept.leasingo.de You can find more items - new and used - in our store! International shipping costs on request!

Condition: like new (used), Year of construction: 2022, operating hours: 50 h, EDM 313MF30-SLM, Year of manufacture 2008/2023 Technical data: Adjustment travel XxYxZ 620x420x400mm workpiece clamping table 1000x600mm tank size 1070x670mm Filling height of the working tank 400mm distance table-electrode holder 150/550mm Workpiece weight max.1500 kg Dielectric min. 1200 L dimensions 2550x2430x2500mm Weight of the machine 3900 kg Equipment: - color: aluminum metallic (silver) - new electrical cabinet - lifting speed (highjump) 15m/min. - contact protection new - cooling unit Termogamma TG13/14 - linear scale in all axes - C-axis 100rpm, direct measurement 0,0001 Djdpfjmx Slhex Aptjkt Holding brake - chuck EROWA ITS/Hirschmann/3R - Cartridge filter system - User interface MF30 V.3.0 - Exopuls+ 60A Rev. 4 - New ball screw, bearings, couplings - Screen Automation Touch Panel - Hand control panel with enable button - Pumps, filling - filter - and spraying pump - New maintenance unit with digital pressure switch - New valve terminal - Table revised (steel) - WZW 6-fold, option 20/30-fold - Co2 extinguishing system - Warranty 12 months - Transport - IB on site - Training

Condition: used, Tenoning spindle 1 0 Number of milling agregates 2 St. Spindle diameter 40,50 mm Item 1: Okoma UF1 S Angle Combination Unit and Item 2: UF2 EG Rebating Machine, incl. Item 3: Tooling Set for IV78 Timber Windows, IV78 Timber Entrance Doors, and IV78 Timber-Aluminum Windows (Gutmann system) with straight and angled sash profiles For sale on behalf of a customer ----- Manufacturer's Technical Description: Item 1: Okoma UF 1 S Tenoning and Profiling Machine / Rebating Machine ----- Compact, heavy-duty automatic window machine featuring a cast-iron construction, consisting of: Top-mounted cross-cut saw with 12-position turret stop system; Positive-guided saw guard for accident prevention Tenoning spindle: 40 mm diameter x 252 mm length; 2-step stroke mechanism for 3 tool positions (stroke height: 83 mm); Motor: 7.5 kW Sliding table: Adjustable on both sides from 0 to 60 degrees Automatic feed system with various infinitely variable speed settings; dual pneumatic clamping system; Length stop (LAS) with 3-position system, 2300 mm capacity Automatic transfer unit to the profiling section Profiling spindle: 40 mm diameter x 252 mm length Pneumatic stroke: 112 mm (adjustable) for 2 tool positions Motor: 7.5 kW; Spindle horizontally adjustable relative to the tool cutting edge; Adjustable front milling fence jaw Glazing bead saw with 3 kW motor and 4-position turret head adjustment; Heavy-duty articulated feed system, infinitely variable from 0 to 25 m/min. adjustable, Roller groups pivotable inward and outward Counter-stop with 5-position turret head Frame milling unit ----- Item 2: OKOMA Automatic Rebating Machine, Model UF 2 EG ----- Power Specifications: - Operating voltage: 3-phase, 380 V, 50 Hz - Compressed air: Air requirement: 13 NL/min; Operating pressure: 8 bar Conditioned air: According to Pneurop 6611 Dsdpfx Asy T R Tbsptjkt 1. Profiling Spindle 1: - Spindle arrangement: Right - Power: 11 kW - Speed: 7000 rpm - Direction of rotation: Climb and conventional milling - Spindle diameter: 50 mm - Usable length: 272 mm - Max. tool diameter: 230 mm - Vertical (U-axis) movement of the profiling spindle - Vertical positioning: Actuation: Pneumatic cylinder; 90 mm stroke for 3 tool positions Position sensor: Limit switches - Horizontal positioning: Actuation: Pneumatic cylinder (forward/backward) Position sensor: Limit switches - Automatic plunge mechanism: Plunge speed adjustable to ensure tear-out-free rebating - Safety and dust extraction hood with 140 mm diameter connection port 2. Profiling Spindle 2: - Spindle arrangement: Right - Power: 11 kW - Speed: 7000 rpm - Direction of rotation: Counter-rotation - Spindle diameter: 50 mm - Usable length: 272 mm - Max. tool diameter: 230 mm - U-axis movement of the profiling spindle - Vertical positioning: Drive: Pneumatic cylinder; 90 mm stroke for 3 tool positions Position sensor: Limit switches - Horizontal positioning: Drive: Pneumatic cylinder (forward/backward) Position sensor: Limit switches - Safety and dust extraction hood with connection port (140 mm diameter) 3. Hardware Routing Unit EG: - Spindle arrangement: Right - Drive: 3 kW three-phase motor - Speed: 6000 rpm - Spindle diameter: 30 mm - Usable length: 47 mm - Vertical positioning: None - Horizontal p...

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, input voltage: 400 V, spindle mount: MK 4, drilling depth: 150 mm, total width: 500 mm, total length: 700 mm, overall weight: 290 kg, Equipment: documentation/manual, 3-phase 400V, 2-speed motor is running smoothly! Geared head with 8 spindle speeds. Spindle RPM adjustable from 75 to 3010. Motor runs in both left and right directions. Spindle power downfeed. 8 feed rates adjustable from 0.004 to 0.30 mm/revolution. Adjustable drilling depth. Maximum drilling depth: 150mm MT4 spindle mount. Tool ejector. E-Off switch. Head and table are height-adjustable. Table size: 500x400mm Good overall condition. Dsdpfx Apszycqcetekt Made in Sweden. Year of manufacture: 2008 Weight: 290KG Overall dimensions: 70x50x180CM Contact us for shipping options! €2,850.00

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, power: 3 kW (4.08 HP), input voltage: 400 V, type of input current: three-phase, cutting height (max.): 2,200 mm, cutting width (max.): 4,100 mm, saw blade diameter: 250 mm, height adjustment type: pneumatic, actuation type: pneumatic, total length: 4,100 mm, total height: 2,200 mm, overall weight: 700 kg, Equipment: CE marking, scorer, Available from the last week of August. We are offering this very well-maintained Holzkraft VPS 2241 VR ED vertical panel saw, manufactured in 2022. The machine was installed and put into operation at our facility in May 2023. Holzkraft VPS 2241 VR ED – vertical panel saw (commissioned in 2023, excellent condition) The machine is connected and can be tested. Selling my vertical panel saw, Holzkraft VPS 2241 VR ED, purchased and assembled new in 2023, and therefore in very good condition. Selling due to expansion. Features & Highlights: • Scoring device for clean, tear-free cuts • Digital measuring displays (horizontal & vertical) • Panel positioning on movable rollers (no lifting required) • Pneumatic locking of the saw carriage • Vertical/horizontal switching • Robust, torsion-resistant machine frame • Integrated dust extraction for direct connection to a dust extraction system The machine runs perfectly, no defects. Technical Data: • Cutting length: 4100 mm Dksdsyxv T Rjpfx Aptjt • Cutting height: 2200 mm • Cutting depth: 60 mm • Saw blade: Ø 250 mm • Motor: 3 kW / 400 V • Weight: approx. 700 kg Condition: • Year of manufacture 2022 / Installation: 2023 • Low usage • Ready for immediate use If you have any questions or require more information, please send us a message or call us.

Year of construction: 2023, condition: used, Used Machine Year of Manufacture: 2023 Features and Technical Specifications: - Stationary, oil-lubricated 2-cylinder piston compressor - Two-stage compression - V-belt drive - Intercooler and aftercooler - Condor pressure switch - Motor protection and safety valve - Tank pressure gauge - Check valve and relief valve - Condensate drain valve - Additional connection fittings with blind plugs - Rubber vibration dampers - Manhole opening for tank inspection - Tank compliant with AD-2000 regulations - Suction capacity: 660 l/min - Effective flow rate: 520 l/min - Maximum operating pressure: 10 bar - Motor power: 4.0 kW / 5.5 PS - Power connection: 400 V / 50 Hz - Start type: Direct start - Speed: 1,025 rpm - Vertical, internally coated 270-liter compressed air tank - Air outlet: 3/4-inch female thread with shut-off valve - Sound pressure level: 78 dB(A) Dedpfx Aezy Dzioptokt - Dimensions: 750 × 705 × 1,800 mm - Weight: approx. 170 kg

Condition: used, Year of construction: 2015, operating hours: 38,504 h, functionality: fully functional, torque: 200 Nm, controller manufacturer: Siemens, controller model: 840D solutionline Operate, rotational speed (max.): 10,000 rpm, overall weight: 9,900 kg, spindle speed (max.): 10,000 rpm, operating hours of spindle: 12,935 h, number of spindles: 1, number of slots in tool magazine: 60, DMG MORI DMC 1450 V Vertical Machining Center | Year of Construction 2015 | SK40 & 60-position Magazine Dkedpfxozypzzj Aptot For sale is a robust and precise vertical machining center from the manufacturer DMG MORI, model DMC 1450 V. This machine, built in 2015, is extensively equipped, including with internal cooling, a direct path measuring system, and a 10,000 rpm spindle with 200 Nm of torque. In 2021, the spindle was professionally replaced after an incident. General Machine Data * Manufacturer: DMG MORI * Model: DMC 1450 V * Year of Construction: 2015 * Machine Number: 14595607194 * Operating Hours: 38,504 h * Spindle Hours: 12,935 h * Machine Weight: 9,900 kg Control System * Type: Siemens 840D solutionline Operate 3D control system Spindle * Speed: 10,000 rpm * Torque: 200 Nm * Tool Clamping: SK40 * Note: Spindle replaced after incident in August 2021 (according to service history) Tool Changer * Magazine Positions: 60 positions * Tool Clamping: SK40 Coolant & Disposal * Internal coolant supply (IKZ): Basic package 3 * Blow-through air through the spindle center * Coolant/air switching * Flushing gun for chip flushing * Oil and emulsion mist separator (mechanical) Additional Equipment & Measuring Technology * Path measuring system: Direct path measuring system X, Y, Z * Measuring probe: Infrared TS649 DMG * Enclosure: Operating mode 4 * Software: DMG Netservice - client Excerpt from the Service History * 10/2022: Complete replacement of the X-axis bellows * 03/2022: Replacement of the Y-axis roof * 12/2021: Replacement of the left-hand blind * 10/2021: Timing belt renewed * 08/2021: Spindle replacement after incident * 2020/2021: Work/replacement on the OP019 TFT 19" screen From an insolvency proceeding, sold as is. Offer deadline: September 30, 2026, 6:00 PM. Package price possible for multiple machines from this proceeding. Inspection: September 16, 2026, 10:00 AM - 12:00 PM, Fraunhoferstraße 10-12, 04178 Leipzig. Collection: October 6, 2026, 9:00 AM - 4:00 PM. Further information and offer submission can be found on our IKV Fester GmbH homepage under Auctions.

Condition: ready for operation (used), Year of construction: 2023, operating hours: 1,904 h, spindle speed (max.): 4,000 rpm, travel distance X-axis: 260 mm, travel distance Z-axis: 795 mm, spindle motor power: 18,500 W, controller manufacturer: MITSUBISHI, controller model: M730UM, number of slots in tool magazine: 12, number of axes: 5, This 5-axis DMG MORI MORI NLX 2500/700 SY was manufactured in 2023. It features a turning length of 700 mm and a powerful main spindle with a maximum speed of 4,000 rpm. The machine is equipped with a 12-station turret and integrated automation for efficient parts handling. If you are looking to get high-quality turning capabilities, consider the DMG MORI MORI NLX 2500/700 SY horizontal turning machine we have for sale. Contact us for further details. - Control Unit: MITSUBISHI M730UM with CELOS (MAPPS V) on 21.5-inch Multi-Touchscreen ERGOline Touch- Turning Length: 700 mm- Main Spindle (Spindle 1): 18.5/18.5/15 kW (25% ED/50% ED/cont.), 4,000 rpm, JIS A2-8 spindle nose, Ø91 mm spindle bore- Main Spindle Chuck: 10" Hydraulic 3-jaw chuck (Kitagawa BR10A821, Ø254 mm) with hollow clamping cylinder (Ø80 mm bar passage)- Counter Spindle (Spindle 2): 11/7.5 kW (25% ED/cont.), 6,000 rpm, JIS A2-5 spindle nose, Ø43 mm spindle bore- Counter Spindle Chuck: 6" Hydraulic 3-jaw chuck (Kitagawa BR06A521E, Ø170 mm) with full clamping cylinder- Turret: 12-station BMT60 turret with 10,000 rpm driven tools (5.5/5.5/3.7 kW power, 40/30/14 Nm torque)- Y-Axis Travel: ±50 mm (Rapid traverse 10 m/min)- X-Axis Direct Measuring System: Magnetic linear scale system (0.01 µm resolution)- Tool Setter: Manual swing-type tool presetter for Spindle 1 and removable tool presetter for Spindle 2- Automation & Parts Handling: Integrated parts catcher for main/counter spindle (up to Ø80 mm x 200 mm, 3 kg max), workpiece discharge conveyor belt, pneumatic workpiece ejector (Spindle 2)- Bar Feeder & Interface: Bar feeder interface (multi-brand) with Top Automazioni X-Files 380M 3m bar feeder (80 mm max bar diameter)- Coolant & Filtration System: Hinge-belt chip conveyor (right side discharge), 0.8 MPa high-pressure coolant pump, INTERLIT pump unit with 15 bar high-pressure pump & double cartridge filter, coolant gun- Auxiliary Equipment & Interfaces: Oil mist collector interface (Ø150 mm port), 3-phase autotransformer (45 kVA, 400V/200V, 50 Hz), double foot switch for chuck operation- Machine Operating Hours (from HMI readout):- Machine Power-On Time: 8,120 hours- Program Run Time Head 1: 3,751 hours- Cumulative Cutting Time Head 1: 1,904 hours Technical Specification Dsdpfx Apszy N Nlstjkt Counter Spindle Yes Driven Tools Yes

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, Used semi-automatic swivelling frame band saw, KASTOmicut U2.6, MFG: 2023, serial number: 6153102136, excellent condition, very little used, it will be delivered with the two rollers from the pictures. Dedevyl Ihepfx Aptjkt Universal, semi-automatic band sawing machine of very robust construction, designed for the rough use in workshops and capable to perform any cutting-to-length or miter cutting tasks (-45°/+60°) in the case of tubes, profiles and solid material. The infinitely adjustable cutting speed and the infinitely adjustable fully hydraulic cutting feed allow a sensitive and blade-saving cutting. Technical Data Cutting range 90° round: 260 mm Cutting range 90° flat (W x H): 310 x 260 mm Dimensions (L x W): 760 x 1620 mm Height, saw head lowered position: 1690 mm Height, saw head in highest position: 2040 mm Material support height: 950 mm Total weight: 510 kg Performance characteristics Total power: 2.0 kW Saw motor, power – frequency controlled: 1.5 kW Cutting speed infinitely variable – frequency controlled min 20 – 110 m/min Dimensions of saw blade: 3180 x 27 x 0.9 mm Saw blade guides: lateral guiding rollers and back slide bearings, interchangeable Material clamping: mechanical Cutting feed: hydraulic, infinitely variable Saw blade tension: mechanical Saw blade cleaning: by synchronously running, easy to interchange brush Electrical equipment: in accordance with DIN EN 60204. Supply voltage 440 Volt, 60 Hz. Control voltage 24 Volt, DC. Upon request other voltages at additional cost. Working Cycle (Semi-Automatic) Infinitely variable and fully hydraulic saw feed control Rotary table serving as material support Horizontal vice with quick adjustment and hydraulic short stroke Infinitely variable cutting speed 20 – 110 m/min via frequency regulated drive Coolant system with two coolant nozzles Automatic switch-off after end of cut and return stroke of the saw head by approx. 100 mm Infinitely variable mitre adjustment (-45° to + 60°) Infinitely variable saw blade arm adjustment Electrical protection of the saw blade covers (accident prevention rules) Synchronously running chip removal brush Glue anchors to dowel the machine Bi-metal saw blade, 4 - 6 teeth per inch Operating instructions manual according to the EU Machinery Directive and EN 82079 Price: 16.456 Euro + VAT, negotiable , FCA Oradea/Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: good (used), Year of construction: 2001, For sale is a Felder KF-700 SP circular saw/milling machine with a cutting length of 3200 mm. The machine has been inspected and refurbished by our service team and is in good condition. Technical data: Dksdszichyspfx Aptet - Cutting length 3200 mm - Cutting width 850 mm - Cutting height 103 mm - Max. saw blade diameter 315 mm - 4 milling speeds - Direction of rotation switch - 3 motors, each with 3 kW / 4.1 hp - Year of manufacture 2001 The machine is located in A-5431 Kuchl and can be inspected at any time during our opening hours. Subject to prior sale! Related terms: circular saw, milling machine, combined machine Reference: R-B17MP

Condition: repair required (used), Year of construction: 2017, functionality: not functional, machine/vehicle number: P177ZG753, Technical characteristics: # Machining Workspace: X 500 mm; Y 400 mm; Z 330 mm # Axis Description: 3 LINEAR AXES (X, Y, Z) + 1 rotary table axis (A-axis) with index dividing head, direct angular measurement system, number of revolutions 50 min⁻¹, accuracy +/- 5" # A-axis Swivel Range: +/-170˚ # Maximum Clamping/Workpiece Dimensions: 650 x 400 mm; max. weight 300 kg # Rapid Traverse: X/Y/Z 54 m/min # Spindle Speed: 100–10,000 rpm, spindle motor power 11 kW # Spindle Taper: BBT30 (with internal cooling) # Automatic Tool Changer: 1x21 tools, chip-to-chip average time 1.5 sec # Maximum Tool Size: Ø40 mm / length max. 200 mm / 2 kg Electrical connection: # Voltage: 3x400V/50Hz # Installed Power: approx. 20 kVA / 22A Dimensions: # Installation space: approx. 1.65 x 3.2 m (with chip conveyor) x 2.8 m # Weight: approx. 8,500 kg Dodpoxxt Ehjfx Aptjkt Equipment includes: # This 4-axis FANUC Robodrill α-D21LiB5 was manufactured in 2016. Ideal for precision machining, this vertical machining centre offers robust performance and reliability. # CNC Control: Model 31i model b5 # 4th axis and tailstock: Fanuc DDR-TiB 178DU039 2017/08 and TSUDAKOMA tailstock # Chip extractor & coolant filtration unit max. 40 bar: Mosnic model 1641/2010 # Spindle, Guideways, and Electrical Cabinet Cooling Systems # Oil Vapor Absorption/Recovery System: Bristol model B 1000 EF # Fire suppression: Kraft & Bauer # Part presence detection: with low pressure air sensors # Automation: Lateral door automatic and interface ready for automation # In-process inspection: Renishaw TRS2 # Documentation: incomplete Machine condition: NOT WORKING # Hydraulic unit defective # Two emulsion pumps # Guideway lubrication pump # Safety switch Euchner

Condition: excellent (used), Year of construction: 2013, HT 665 MC plus TCMY - FANUC Multi-axis CNC turning machine for complete machining of turning/milling parts; Integrated spindle motors (ISM) on the main and counter spindle with thermocompensation system (liquid-cooled) Drive power: Main spindle - 29 kW Counter spindle - 22 kW Speed range: Main spindle 0 - 5000 rpm Counter spindle 0 - 7000 rpm Spindle connection (DIN 55026): Main spindle: KK 6 (max. bar diameter ø 65mm) Counter spindle: KK6 Y-axis: Travel range +/- 50mm The Y-axis is designed so that the resulting cutting forces are distributed across two axes. This results in extremely high rigidity for all machining operations. Preloaded roller guides in all linear axes; digital drive system, integrated spindle encoder; State-of-the-art control technology FANUC 18i TB with Manual Guide i dialog programming. Includes: ·Draw tube cylinder including draw rod ·Part ejector and flushing through the counter spindle ·2x 12-position tool turret VDI 30 radial with direction logic for up to 2x 12 driven tool stations! Swivel speed adjustable with feed switch. o Performance data: o Max. 6.7 kW at 2650 rpm o Torque constant 25 Nm o Speed range 0-5000 rpm o C-axis for main and counter spindle ·Part removal device for the finished parts ·Chip conveyor with a discharge height of 1200mm programmable (Type "hinged belt") ·Coolant system integrated into the chip conveyor 2 pcs. high-pressure pumps with 14 bar 2 pcs. flushing pumps with 3.7 bar ·Electrostatic oil mist separator ·Hydraulic unit ·Machine light Dkodpfx Apjzczgvotet ·Documentation Year of manufacture: 2013 Includes: two Hainbuch chucks, collet chuck for collets 185E plus reduction is also included.

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 6153102135, Used semi-automatic swivelling frame band saw, KASTOmicut U2.6, MFG: 2023, serial number: 6153102135, excellent condition, very little used, it is delivered with the roller from the pictures Universal, semi-automatic band sawing machine of very robust construction, designed for the rough use in workshops and capable to perform any cutting-to-length or miter cutting tasks (-45°/+60°) in the case of tubes, profiles and solid material. The infinitely adjustable cutting speed and the infinitely adjustable fully hydraulic cutting feed allow a sensitive and blade-saving cutting. Technical Data Cutting range 90° round: 260 mm Cutting range 90° flat (W x H): 310 x 260 mm Dimensions (L x W): 760 x 1620 mm Height, saw head lowered position: 1690 mm Dkedpfsvyl Dvsx Aptot Height, saw head in highest position: 2040 mm Material support height: 950 mm Total weight: 510 kg Performance characteristics Total power: 2.0 kW Saw motor, power – frequency controlled: 1.5 kW Cutting speed infinitely variable – frequency controlled min 20 – 110 m/min Dimensions of saw blade: 3180 x 27 x 0.9 mm Saw blade guides: lateral guiding rollers and back slide bearings, interchangeable Material clamping: mechanical Cutting feed: hydraulic, infinitely variable Saw blade tension: mechanical Saw blade cleaning: by synchronously running, easy to interchange brush Electrical equipment: in accordance with DIN EN 60204. Supply voltage 440 Volt, 60 Hz. Control voltage 24 Volt Working Cycle (Semi-Automatic) Infinitely variable and fully hydraulic saw feed control Rotary table serving as material support Horizontal vice with quick adjustment and hydraulic short stroke Infinitely variable cutting speed 20 – 110 m/min via frequency regulated drive Coolant system with two coolant nozzles Automatic switch-off after end of cut and return stroke of the saw head by approx. 100 mm Infinitely variable mitre adjustment (-45° to + 60°) Infinitely variable saw blade arm adjustment Electrical protection of the saw blade covers (accident prevention rules) Synchronously running chip removal brush Glue anchors to dowel the machine Bi-metal saw blade, 4 - 6 teeth per inch Operating instructions manual according to the EU Machinery Directive and EN 82079 Price: 15.428 Euro + VAT, negotiable , FCA Oradea/Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: used, Year of construction: 2008, We are selling one fully functional Schmidt Sweeper Swingo 200 from year of manufacture 2008. Equipped with a VM engine 560/9 delivering 62 kW, dual broom system, Motec reversing camera, passenger seat, directional switch for forward/neutral/reverse, 2 m³ debris container capacity, new TÜV (vehicle inspection), new service, new brushes, and 215R14C Kumho tires. The machine received a new engine approximately 2 years ago. Operating hours: around 800. The machine is ready for immediate use. Further details available upon request. Location: 94491 Hengersberg. Dkedpsyq Au Defx Aptst

Condition: good (used), Year of construction: 2017, operating hours: 60 h, functionality: fully functional, machine/vehicle number: 333840, travel distance X-axis: 450 mm, travel distance Y-axis: 200 mm, travel distance Z-axis: 510 mm, spindle mount: MK 3, quill travel distance: 120 mm, type of input current: three-phase, table width: 210 mm, input voltage: 400 V, table length: 750 mm, drilling capacity: 32 mm, distance table center to spindle nose: 275 mm, rotational speed (max.): 3,200 rpm, rotational speed (min.): 95 rpm, rapid traverse X-axis: 240 m/min, Equipment: documentation/manual, The milling machine is fully functional and can be tested. It is being sold due to the purchase of a larger model. Technical documentation is available. The milling machine has a robust base cabinet housing the coolant pump. The automatic table feed features: - Emergency stop function, no automatic restart - Infinitely variable speed control and rapid traverse Dkjdjyrib Tjpfx Aptst - Left/right feed direction - Overload protection and limit switches - Speed: 0 - 165 rpm - Rapid traverse: 240 rpm Three-axis position display, accuracy class 0.01 mm.

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, Weiler Primus VC precision center lathe, year of manufacture 2008, 3-axis digital display, Siemens, with AC drive, stepless speed control, CE compliant! Technical data: Dsdpfxszl T Tre Aptjkt >> Year of manufacture 2008, machine no. DB-01 >> Center height 140 mm >> Center distance 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore 40 mm >> Short taper spindle head, DIN 55027, size 5, with bayonet lock >> Hand lever tailstock, MK 3 >> Feeds from 0.02 to 0.63 mm/rev >> Possible threads: metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and equipment: >> 3-axis digital display, Siemens >> Quick-change tool holder with collets (see pictures) >> Tool cabinet >> 3-jaw chuck 160 mm with 5 sets of jaws >> Stop >> Mulifix size A with 4 steel holders >> Electric chip guard >> Machine lamp >> Drill chuck, centering point >> Change gears >> Splash guard About the machine: Offered is a Weiler Primus VC lead screw and draw spindle lathe, year of manufacture 2008, in very good condition. The control system, in combination with a precision center lathe from Weiler, performs the following functions: graphical display of travel paths and direction, graphical representation of the measuring system on the lathe, compensation of tool corrections, zero point adjustment to compensate for the workpiece position, radius/diameter switching, graphical display of the main spindle rotation direction, graphical display of the position of the machine's speed potentiometer. A very nice lathe with AC drive and stepless speed control of the working spindle. All slides move very smoothly and evenly. Even at high speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and allows surfaces to be produced with a ground finish. The digital display from Weiler makes working even easier and more precise. Take advantage of the opportunity to inspect this machine on-site under power and convince yourself of its condition.

Condition: like new (used), functionality: fully functional, Year of construction: 2022, load capacity: 1,400 kg, working height: 8,860 mm, operating hours: 350 h, Equipment: documentation/manual, STILL FM – X 14. Reach Truck – 2 pcs. Forklift For sale: Reach trucks, condition like new, only 350 engine hours, year of manufacture 2022. Serviced exclusively by STILL. Detailed description see photo. • Quantity: The offer is for 2 units of STILL FM – X 14 forklifts. • Batteries: Attention, 2 batteries are included for each forklift (4 batteries in total) – ideal for multi-shift operations! • Hydraulic telescopic forks extendable from 80 cm to 120 cm!! • Load capacity: 1400 kg Price: €15,900 Top condition, serviced exclusively at STILL !!! Dkjdouvdbujpfx Aptst For sale: Reach Truck – condition like new, only 350 engine hours, year of manufacture 2022. Serviced exclusively by STILL.STILL FM – X 14. Reach Truck. x 2 pcs.Load capacity: 1400 kgPrice: €15,900Attention: The price includes 2 batteries, making it suitable for multi-shift operations!Detailed Description:Hydraulic telescopic forks: extendable from 80 cm to 120 cm!!Vehicle width: 1,302 mmLoad wheel tires: Diameter 285 mm, polyurethaneDrive wheel tire: Diameter 360 mm, polyurethaneBattery change: Side battery replacement via changeover rack, battery also transportable by craneMast functions: Hydraulic mast reach cross-shift +/- 50 mm, with mast tilt, including necessary hydraulics (4 functions)Fork carriage: Type A, 4 rollers, width of fork carriage: top 840 mm, bottom 755 mmOverall height: 3,300 mmFree lift (H2): 2,740 mmRated lift: 8,300 mmMaximum height (h4): 8,860 mmLoad capacity at maximum lift: 1,350 kgLift height sensor: LED height sensor – preparation for innovative lift height measurement using an LED light beam for precise measurement of optional assistance functionsForks: 1150 x 100 x 40 mm, 2A, LSP 600Hydraulic system: Central position of fork tilt/mast and sideshift selectable via buttonsTilt angle: 0.5/2 degrees forward/backward mast tiltTransport: Mast disassembled before shipping for easier transportOverhead guard: Driver's overhead guard with head paddingOverhead guard dimensions (short version): Overall height: 2200 mm, depth: 645 mmAdditional roof equipment: Overhead guard pillar for mounting MMS terminals or similar auxiliary equipmentInterior rearview mirror: Panoramic mirror on the drive side mounted on the overhead guard for improved visibility when driving out of rack aislesDisplay: Remaining battery charge indicator integrated into the displayDriver's seat: Hydraulically suspended comfort driver's seat MSG 65 with fabric coverSeat adjustments: Infinitely variable weight adjustment, backrest tilt, longitudinal adjustment, and lumbar supportHydraulic control: Joystick 4Plus (central control element combines lift, tilt, and auxiliary hydraulic functions, including horn)Drive activation: Designed as a foot and seat switch combined with single-pedal control and travel direction change via rocker switchSteering: Fully electric 360° steering, height-adjustable steering wheelIgnition switch: Start/Stop buttonAdditional electrical equipment: For external systems (data terminal and scanner) consisting of:Assistance system: Infinitely variable speed reduction depending on the steering angle (CSC - curve speed control)Warning device: STILL SafetyLight 4PLUS with 4 LEDs and a moving light spot in the direction of travel to show the vehicle's approach directionFleet Manager 4.0: Online fleet management via WEB application (GPRS - SIM card, access via employee cards, data, reports, ...)Number of batteries included: 2 pcs !!!!!Battery specifications: 48 V / 4PzS 620 Ah

Condition: used, Year of construction: 2012, functionality: fully functional, Weiler Primus VC Precision Lathe, manufactured in 2012. 3-axis digital display from Siemens with AC drive and stepless speed control. CE certified. Technical specifications: >> Year of manufacture: 2012, Machine No. HB 01 >> Center height: 140 mm >> Distance between centers: 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore: 40 mm >> Short taper spindle head, DIN 55027, size 5, with bayonet lock >> Hand lever tailstock, MK 3 >> Feeds from 0.02 to 0.63 mm/rev Dodpfjzl T Hxjx Aptokt >> Possible threads: metric, inch, module, and diametral pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight: approx. 800 kg >> Spindle brake can be activated >> Machine dimensions: approx. 1.4 m x 1.55 m x 0.95 m Accessories and equipment: >> 3-axis digital display from Siemens >> Quick-change tool holder with collets (see pictures) >> Tool cabinet >> 3-jaw chuck, 160 mm, with 7 sets of jaws >> Stop >> Mulifix, size A, with 4 steel holders >> Electric chip guard >> Machine lamp >> Spindle stop, drill chuck, center >> Change gears >> Splash guard About the machine: Offered for sale is a Weiler Primus VC lead screw and draw spindle lathe, manufactured in 2012, in very good condition. The control system, in combination with a precision lathe from Weiler, performs the following functions: graphical display of travel paths and travel direction, graphical representation of the coordinate system on the lathe, compensation of tool corrections, zero point shift to compensate for workpiece position, radius/diameter switching, graphical display of the main spindle direction of rotation, and graphical display of the position of the machine's speed potentiometer. This is a very nice lathe with AC drive and stepless speed control of the spindle. All slides move very easily and smoothly. Even at high speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and allows for the production of surfaces that are as smooth as ground surfaces. The digital display from Weiler makes working even easier and more precise. Take advantage of the opportunity to inspect this machine on site while it is powered up and to convince yourself of its condition.