Used Disc Sanding Machine for sale (70,062)

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Dcsdet Tqy Eopfx Af Asi Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: good (used), Year of construction: 1992, Single-piece sanding machine sanding from top and bottom electric height adjustment with digital display continuously variable feed speed star/delta starter pneumatic belt tensioning main switch sanding belt oscillation finishing brush unit top and bottom, manual height adjustment Working width: 190 mm Working height: 4 - 150 mm Min. workpiece length: approx. 280 mm Abrasive belt dimensions (L x W): 1850 x 200 mm Feed speed: 5 - 25 m/min Installed power: approx. 14 kW Extraction port diameter: 2 x 180 mm Dimensions (L x W x H): 2000 x 1000 x 2050 mm Weight: approx. 1800 kg Dodpfxowyda Ue Af Aeci Incl. infeed and outfeed roller conveyor (L = 1600 mm, non-driven) Note on used machines: • Technical data subject to errors and prior sale. • Quoted prices are ex-works – loaded free of charge! • The machines have been cleaned and function-tested. • All machines are sold as inspected, with no claims to warranty. Buyers are welcome to inspect machines at the location. • Special agreements are only valid in written form. (We answer inquiries only when your address and telephone number are provided!)

Condition: used, Year of construction: 1953, grinding wheel dia. x width ca. 200 x 25 mm magnetic clamping plate ca. 450 x 170 mm cross feed of the table 200 mm revolutions of grinding spindle 3000 U/min grinding wheel hole diameter 51 mm weight ca. 1300 kg 0,001 - 0,013 mm grinding length 600 mm Dedpfexu Nw Eox Af Aoci Surface grinding machine Includes extractor 1 additional grinding wheel holder Machine was in occasional use until recently

Condition: used, Year of construction: 2008, total length: 2,060 mm, total width: 830 mm, total height: 1,180 mm, Colour: Grey Empty weight: 566 kg - Year: 2008 - Documentation available: No - CE certificate present: No - Table length [mm]: 1000 - Table width [mm]: 400 - Sanding belt width [mm]: 200 - Sanding belt length [mm]: 3200 - Extraction nozzle diameter [mm]: 120 - Conveyor belt speed [m/s]: 13 - Min. tilting angle [°]: 0 - Max. tilting angle [°]: 45 - Transport dimensions: 2060mm x 830mm x 1180mm (l x w x h) - Transport weight [kg]: 566kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Dcodsywlfyspfx Af Aoi Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Dimensions (l x w x h) approx.: 3200 x 1800 x 1600 mm Weight approx.: 500 kg 3 spindles, 1 milling spindle, 2 - 3 grinding and milling spindles, Dedoxrlgwjpfx Af Aoci feeder belt approx. 100 mm wide, total working length approx. 3000 mm, extendable workpiece support

Condition: excellent (used), ITALMECCANICA PROFILWOOD MAK6B Automatic Grinder / Sanding machine 6 sanding units, each 1.5 kW, Dcsdpjdykwlsfx Af Asi max. working width 250 mm, Depth 0-250 mm, min. Dimensions in mm: approx. 4700 x 2000 x 2300, Weight in kg: approx. 3000, (Makor, Delle Vedove, Venjakob, Flader)

Condition: excellent (used), Year of construction: 1984, Description to follow! Dodezbczlepfx Af Ajci

Condition: excellent (used), Year of construction: 1993, Enorm edge sanding machine (now Kündig) In very good condition. Type: LBK 160 Year of manufacture: 1993 With veneer edge sanding attachment Oscillation can be switched on. Dedezbyt Ejpfx Af Aoci Electric height adjustment of the sanding unit Table can be tilted up to 45 degrees Sanding belt width 150 mm Sanding belt length 2600 mm 3 kW motor 2 additional motors for height adjustment and oscillation With feed system Weight approx. 400 kg Location: in stock at 54634 Bitburg - immediately available -

Condition: excellent (used), functionality: fully functional, input voltage: 400 V, year of last overhaul: 2024, total height: 950 mm, total length: 880 mm, total width: 3,075 mm, type of input current: three-phase, DGUV certified until: 07/2027, Riehle Belma 2000 Icing Machine 3 icing curtains Stainless steel design, mobile with tilting device for rolls very robust technology DGUV V3 certified – only available from us Djdoyaf Eqopfx Af Asci Connection: 400V, 16A-CEE plug Dimensions: 3075 x 880 x 950 mm, L x W x H Used machine, cleaned & SAB inspected with warranty + spare parts service Optional: Service package Maintenance contract Spare parts box Delivery service Training & commissioning We have other bakery machines in stock!

Condition: used, Year of construction: 1992, ~ 2.780 mm Dcedpszawi Uefx Af Aji Working width ~ 950 mm Motor output 6 kW Johannsen Type T 95 long-belt sander for the precise sanding of solid wood and veneer surfaces. The machine is ideal for joineries and high-end interior finishing, and its sturdy construction and precise belt control ensure a uniform finish.

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, The machine is in good condition, has been in use until recently, and is now available for sale due to a new purchase. The machine has been regularly serviced. It is ideally suited for sanding solid wood, both straight and profiled parts. The processing side, with its guides, features an adjustable sanding shoe. The feed mechanism is an ideal addition for finer edge sanding on straight edges. The machine has a compressed-air-operated belt oscillation for optimal sanding results. The machine has a chassis. Various sanding belts are included. Dsdezdvupjpfx Af Asci

Condition: as good as new (ex-display), Year of construction: 2026, 5222454 LIBRA 45/2 RTC 135 Wide Belt Sander 5257433 "Z" Designation for RTC 135 5257452 Vacuum table with electric fan 3 kW 5257453 Oscillating belt air-blast device for 5257454 Oscillating belt air-blast device for 5257462 Reinforced motor 15 kW (20 HP) 5257485 Roller table at infeed and outfeed for 5257499 Grooved rubber pressure roller, 2nd position 5257500 Grooved rubber pressure roller, 3rd position 5257504 Infinitely variable conveyor feed with inverter 5257605 Door with inspection window 5257606 LED lamp for internal illumination TECHNICAL DATA Dimensions and Weights Length (product) approx. 1800 mm Width/depth (product) approx. 2000 mm Height (product) approx. 2070 mm Extraction Connection Number of extraction ports: 2 Extraction port diameter: 200 mm Electrical Data Feed motor power: 0.8 kW Connection voltage: 400 V Dcsdpoy Ehiwofx Af Aei Mains frequency: 50 Hz Height adjustment motor power: 0.25 kW Output power (motor power): 11 kW Sanding Unit Sanding belt length: 2150 mm Sanding belt width: 1370 mm Max. sanding width: 1350 mm Feed Unit Feed speed: 4.5 / 9 m/min Workpiece Min. workpiece height: 4 mm Max. workpiece height: 170 mm Product Information EU 2023/2854 Type of generated data: usage data Format of generated data: common, machine-readable formats, e.g., JSON Data volume: up to 5 MB Continuous real-time data generation: yes Data storage location: on the device and a remote server Data access: on the device and via physical and wireless interfaces Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2024, The Uniq series is a full-fledged base model in our product range and shares all the characteristics that have made the Kündig edge sanding machine renowned in the market as a robust, versatile precision tool. Part of its extremely robust construction is the motor-driven oscillating sanding unit, which offers a maximum oscillation stroke of 90 mm and the possibility of motor-driven inclination of up to 45°. All common edge processing operations can be performed at the up to four sanding stations. Kündig Uniq edge sanding machine, front and rear Ingenious design – the sanding unit The heart of all our edge sanding machines is the sanding unit. It offers a range of intelligent functions and features. For example, in our machines, the sanding belt does not oscillate by tilting the belt rollers. Instead, the entire sanding unit moves up and down. The oscillation stroke, as well as the oscillation range, are easily set by pressing a button. Thanks to the flexible adjustment and the large oscillation stroke, sanding belts can be used optimally over their entire width, without laborious adjustment of the worktable height. The oscillation mechanism is driven by a separate motor. The tilting of the sanding unit is also conveniently done using a rotary switch and with the help of its own motor. The unit can be tilted between 90° and 45°. Thanks to the well-thought-out pivoting mechanism, the full oscillation is always available and simultaneous sanding on both sides is possible. The different table heights of the front and rear sanding stations also ensure that the belt is not used at the same height at the same time. Furthermore, the combination of the pivoting mechanism and the different table heights ensures that the distance between the sanding unit and the worktable remains minimal at every angle of inclination. Changing the belt is also quick and easy, taking only seconds. The four sanding stations Dcsdjfig Rwepfx Af Aji 1. Sanding station: "Veneer side" The front sanding station is used for the precise calibration of materials and functions like a planing machine. The feed stop is adjusted using a rotary handle to set the material removal to within a tenth of a millimeter. Importantly, the stop is not tilted. The feed stop, sanding pad, and discharge stop are always parallel to each other. Rounding of workpieces is thus excluded. Fine adjustment of the sanding pad for grain compensation or setting to zero between stops and pad is possible via a handwheel. The massive worktable is fitted with sliding pads on this side. 2. Sanding station "Solid wood side" This station is ideal for sanding flat, angled, chamfered, or externally rounded workpieces. Again, the entire sanding unit oscillates. The belt runs across its entire width on a graphite surface that keeps it cool. On the solid wood side, there is also a mitre stop. Supplied accessories: Half-round table Additional table with sanding rollers Location: In stock, 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2026, Heavy-duty machine stand guarantees high torsional rigidity and vibration-free operation. Improved sanding results through sanding belt oscillation via a separate geared motor. Oscillation can be switched on or off as desired. Veneer edge sanding device with fine adjustment included as standard. Grooved infeed guide rail for sanding veneer overhangs. Quick changeover from veneer to solid wood sanding. Height-adjustable sanding table to utilize the full sanding belt width. Height adjustment of the sanding table and swiveling of the sanding unit via handwheels. Height-adjustable auxiliary table with dust extraction for sanding radii. Optimal chip removal through dust extraction at the unit and the cross table. Automatic compensation of belt length differences through spring-loaded belt tension. Dimensions and weights Length approx. 1900 mm Width/Depth approx. 810 mm Height approx. 1230 mm Weight approx. 290 kg Dust extraction connection Dust extraction nozzle diameter 120 mm Drive power Oscillation motor 0.25 kW Work table(s) Work table length 960 mm Work table width 352 mm Work table height adjustment 210 mm Cross table height min. 730 mm Electrical data Power consumption 3 kW Connection voltage 400 V Phase(s) 3 phases Type of current AC Mains frequency 50 Hz Sanding unit Sanding belt length 3000 mm Sanding belt width 150 mm Belt running speed(s) 20 m/s Sanding area length 1050 mm Sanding area width 220 mm Swivel range 0 – 45 ° Oscillation stroke 20 mm Dedpsff Ed Tefx Af Asci Availability: Short-term

Condition: new, Year of construction: 2025, Designed for professional structuring and grinding operations Dedpjff Hdgefx Af Asci Motorized height adjustment of the working units with digital display Units can be switched on individually Highly durable, rubberized conveyor belt Continuously variable feed rate Infeed height remains constant Models str l with continuously adjustable, inverter-controlled brush speed: this enables precise adjustment of the speed to the workpiece material, making it particularly suitable for sensitive materials. Unit for saw-cut appearance available as an option Motorized height adjustment of the units Units can be switched on individually Feed rate continuously adjustable Dimensions and weights Length approx. 1300 mm Width/Depth approx. 1000 mm Height approx. 1300 mm Weight approx. 440 kg Dust extraction connection Extraction nozzle diameter 2 x 150 mm Brushes Diameter 190 mm Length 300 mm Rotation 1500 min⁻¹ Electrical data Power of drive motor 2 x 3.0 kW Power of feed motor 0.22 kW Power consumption 6.25 kW Connection voltage 400 V Phase(s) 3 phases Type of current AC Mains frequency 50 Hz Noise emission Sound power level Lw (idle, without extraction) 65 dB(A) Grinding unit Grinding width max. 300 mm Feed unit Feed speed 1 – 13 m/min Workpiece Height max. 300 mm Weight max. 100 kg

Condition: new, Year of construction: 2024, Holzkraft Edge Sander Type: KSO 200 F with Veneer Sanding Attachment Sanding unit can be swiveled up to 45° via a lever The machine stand made of welded steel guarantees high torsional rigidity and vibration-free operation. Oscillating sanding belt with separate geared motor for better sanding results Oscillation can be switched on/off as required Sanding pad with graphite coating for a longer service life of the sanding belt Height-adjustable sanding table to utilize the entire width of the sanding belt Height-adjustable auxiliary table with dust extraction for sanding radii The spring-loaded belt tension automatically compensates for belt length differences. With double dust extraction Extendable roller table extension With rubber-coated sanding roller Veneer edge sanding attachment with contact shoe with fine adjustment, relief rollers and guide rails With grooved infeed guide for veneer overhangs Quick changeover from veneer edge sanding to solid wood sanding is possible Dimensions and Weights Length approx. 1900 mm Width/Depth approx. 900 mm Height approx. 1350 mm Weight approx. 290 kg Connection for dust extraction Dust extraction nozzle diameter 140 / 100 mm Drive power Oscillation motor 0.25 kW Work table(s) Work table length 960 mm Work table width 350 mm Work table height adjustment 230 mm Height min. 735 mm Height max. 965 mm Longitudinal table height adjustment 230 mm Cross table length 330 mm Cross table width 330 mm Cross table height min. 720 mm Cross table height max. 900 mm Cross table height adjustment 180 mm Electrical Data Power of drive motor 3.0 kW Connection voltage 400 V Sanding unit Sanding belt length 3000 mm Sanding belt width 200 mm Belt running speed(s) 20 m/s Sanding area length 1050 mm Sanding area width 200 mm Oscillation stroke 20 mm Location: In stock at 54634 Bitburg - available immediately - Dedpfxjlht H No Af Aeci

Condition: new, Year of construction: 2025, Holzkraft Edge Sander: KSO 150 F PRO With oscillating sanding belt for the best sanding results Item number: 5390020 Brand: Holzkraft Sanding unit can be pivoted using a hand crank The welded steel machine stand guarantees high torsional rigidity and vibration-free operation Oscillating sanding belt with separate gear motor for better sanding results Oscillation can be optionally activated Granite-coated sanding sole for a longer sanding belt service life Height-adjustable sanding table for utilizing the entire sanding belt width Additional table with extraction openings for sanding radii on the rubberized guide roller Sanding sleeve device with attachable work table The spring-loaded belt tension automatically compensates for belt length differences With adjustable stops, ideal for veneer sanding The grooved veneer stop allows the veneer overhang to be adjusted TECHNICAL DATA Dimensions and Weights Length (product) approx. 1700mm Width/Depth (product) approx. 1000mm Height (product) approx. 1150mm Net weight approx. 300kg Extraction connection Number of extraction nozzles: 2 Extraction nozzle diameter: 100mm Worktable(s) Worktable length: 950mm Worktable width: 450mm Worktable height adjustment: 110mm Electrical data Connection voltage: 400V Mains frequency: 50Hz Oscillation motor power: 0.11kW Dcsdpfov Sk Nnox Af Asi Sanding unit Sanding belt length: 2640mm Sanding belt width: 150mm Belt rotation speed(s): 14m/s Oscillation stroke: 15mm Sanding surface length: 800mm Sanding surface width: 150mm Sanding unit pivoting 0 – 45° SCOPE OF DELIVERY 1x Sanding Belt K100 5x Rubber Rollers Ø25, Ø30, Ø40, Ø45, Ø50 mm 6x Sanding Sleeves K80 - Ø25, Ø30, Ø35, Ø40, Ø45, Ø50 mm On-Board Tool Kit Miter Gauge

Condition: new, Year of construction: 2025, Edge grinding machine with an overhead feed mechanism What distinguishes the Uniq-S from the Uniq is the feed system integrated into the machine table, featuring a rubberized feed belt and an overhead pressure bar. This significantly simplifies the grinding and production of bevelled and chamfered edges, as well as the serial grinding of workpieces. Furthermore, it provides assistance when processing exceptionally large or small parts. The feed speed can be continuously adjusted between 3 and 15 m/min. A soft conveyor belt at the bottom and rubberized rollers on the upper pressure bar gently convey the material. An optional second, lower conveyor belt is also available. The upper pressure rollers can also be replaced with a rubber band, which is particularly helpful when grinding extremely small parts. The Uniq-S is recommended as an all-rounder that enables all types of processing – from solid wood to fine veneer edges – with high quality. The continuously adjustable feed speed allows for optimal adaptation to the material. 1. Grinding station: “Veneer side” Dcsdpfxehqb Rco Af Aei 2. Grinding station: “Solid wood side” 3. Grinding station: “Additional table” 4. Grinding station: “Half-round table” Location: Available from stock in 54634 Bitburg - immediately available -

Condition: good (used), Year of construction: 1997, Manufacturer: MABO Model: BABY S.A.S. BABY 80 Machine type: Edge sanding machine Technical Data Distance between rollers: 1,050 mm Max. sanding belt width: 120 mm Number of speed settings: 1 Main motor: 1.1 kW Sanding belt horizontal Sanding belt tiltable Vertical upwards Weight approx.: 95 kg Space requirement length: 2.65 m Space requirement width: 0.55 m Space requirement height: 1.1 m Location: from stock 54634 Bitburg - Immediately available - Dedpfxexgvcxj Af Ajci

Condition: as good as new (ex-display), Year of construction: 2024, The robust Junior R1 offers all the features that a modern edge sanding machine should have. A solid, cast iron grinding unit with a powerful motor ensures maximum sanding performance. The work table, which is height-adjustable by spring pressure, allows for optimal belt utilization and safe operation. Optionally, a belt oscillation, stepless unit swivel, veneer sanding device, and an additional table for sanding work on the idler roller can be retrofitted. The machine is supplied with a range of sanding belts; a miter and angle stop are also included in the scope of delivery. Technical data: • Motor power: 2.2 kW Dcjdpod R Ev Dsfx Af Aei • Sanding belt size: 150 × 2280 mm • Sanding belt speed: 22 m/sec • Table size: 750 × 350 mm • Space requirement: 1000 × 800 mm • Weight: from 180 kg • Dust extraction diameter: 100 mm Location: In stock at warehouse 54634 Bitburg - free for collection - Can be shipped for an additional fee.

Condition: like new (used), Year of construction: 2025, Holzkraft Edge Sanding Machine Model: KSO 200 F with veneer sanding equipment Sanding unit tiltable up to 45° via lever The machine frame is made of welded steel, ensuring high torsional rigidity and vibration-free operation. Oscillating sanding belt with separate geared motor for improved sanding results Oscillation can be activated as needed Sanding shoe with graphite coating for extended belt life Height-adjustable sanding table to utilize the entire sanding belt width Height-adjustable auxiliary table with extraction for sanding radii Spring-loaded belt tension automatically compensates for belt length variations Double extraction system Extendable roller table extension With rubber-coated sanding drum Veneer edge sanding device with fine-adjustable contact shoe, pressure rollers, and stop rulers Infeed ruler with groove for overlapping veneer Quick changeover from veneer edge to solid wood sanding possible Dimensions and Weights Length approx. 1900 mm Width/depth approx. 900 mm Height approx. 1350 mm Weight approx. 290 kg Dust Extraction Connection Suction nozzle diameter 140 / 100 mm Drive Power Oscillation motor 0.25 kW Working Tables Working table length 960 mm Working table width 350 mm Working table height adjustment 230 mm Height min. 735 mm Height max. 965 mm Longitudinal table height adjustment 230 mm Cross table length 330 mm Cross table width 330 mm Cross table height min. 720 mm Cross table height max. 900 mm Cross table height adjustment 180 mm Electrical Data Main drive motor power 3.0 kW Connection voltage 400 V Sanding Unit Abrasive belt length 3000 mm Dcjdsy Iu N Aopfx Af Asi Abrasive belt width 200 mm Belt speed(s) 20 m/s Sanding surface length 1050 mm Sanding surface width 200 mm Oscillation stroke 20 mm Location: Ex stock 54634 Bitburg — Immediately available —

Condition: used, Year of construction: 2017, working width max. 240 mm Sanding height max. 140 mm weight ca. 2200 kg Dcodpfoxwtwuex Af Aei

Condition: good (used), Code: 0749 Brand: TAGLIABUE - COSTA LEVIGATRICI Model: TT 3 1300 Automatic sanding machine for worktops, furniture, panels, tables Technical data: Working width mm 1300 Max working thickness mm 130 Min working thickness mm 1 Composition: 1° Transversal belt - Motor Hp 15 - Electronic speed variator with display 2° Transversal belt - Motor Hp 15 - Electronic speed variator with display Transversal sanding belt size mm 1350 x 150 Chevron belt size mm 5510 x 140 Belt blowers Belt feed speed mt/min 5/25 Fixed table and mobile head for on-line set-up Panel cleaning rotary blowers Vacuum table Belt cleaning brush Infeed roller conveyor Installed power Kw 32 Compressed air 7 Atm Suction inlets: n° 2 diameter mm 200 - n° 2 diameter mm 150 - n° 2 diameter mm 100 Dcsdjh T Dzqopfx Af Aei Overall dimensions mmm 4400 x 2500 x 1600 h Weight kg 5000

Condition: good (used), Code: 0021 Brand: BOHR - AUSTRIA Model: 150/330 Dedpfx Afji Art Ej Aeci Sanding pad for belt sanding machine Universal sanding pad for belt sanders in graphite for solid wood and veneer - mm 330 x 150 Overall dimensions mm 330 x 150 x 100 h Weight kg 4

Condition: good (used), Code: 0351 Brand: VOLPATO Model: LS - 1N - CE Standard Automatic edge sanding machine for edges and profiles in wood, solid wood, veneer, painted and various materials - CE Standard Technical data Max working height mm 110 Min working length mm 100 Variable-speed belt feed 5–30 m/min – Motor Kw 1,5 Tilting oscillating sanding unit – 2-speed motor 700–1400 rpm – Power 2 Hp Pneumatic belt tensioner – Timed entry and exit of the pad Mechanical oscillation of abrasive belt 0/20 mm Lifting and tilting via handwheel with special key Removable support for large panels Abrasive belt dimensions 80 x 2450 mm Suction inlet diameter 100 mm Compressed air 5–6 atm Overall dimensions mm 2600 x 1400 x 1500 h Dcedpfsy A Sq Tox Af Aei Weight kg 720