Used Filling Line for sale (12,209)

Condition: used, Year of construction: 2018, Overview  The offered filling line for pouch bags was designed by a Swiss company and also delivered by them in 2018. The main manufacturer is Linapack. The line was only used for seasonal production only (2 months a year), therefore the working hours are very low. As the sales volumes are not further increasing, the seller decided to sell the line and stop the production. The line is still assembled and can be shown. It is possible to handle different formats of pouch bags and to do hot filling up to 85°C. The current owner used it for Cocktails but it can also be used for various other non carbonated drinks. Tech. Details Capacity: 50 bags/ hour, depending on the volume 750 -900 l/h Bag dimensions Width: 80 - 180mm Height: 100 - 300mm Filling temperature: 71 - 85 °C Siemens PLC Line consists of  1,000 l buffer tank agitator Flow meter Level detection Cleaning spray ball Integrated into pasteurizer control system Flash pasteurizer Kreuzmayr PAS-900 Capacity: 750 - 1,000 l/h Heated with steam Fully automatic Automatic cleaning with Hot water steam acid caustic With tubular heat exchanger Automatic filler Linapack LFS-1000 Duplex with Siemens PLC Seven Station system motorized magazine with pick and place system to supply pouches Opening of the pouches with vacuum gripper Filling unit with flow meter and temperature sensor, automated rejection, if temperature is too low Sealing of pouches Sealing of pouches Cooling of the seal Pouch discharge Check weigher Cooler and dryer for pouches Cooling in water bath With UV lamps for desinfication Drying by blower, five nozzles Conveyors and collection table Lrodsvptt Rspfx Adwsg

Condition: used, Year of construction: 2014, Overview  This complete isobaric filling line was produced in 2014 by the Italian manufacturer Eurostar and is located in Mexico. The line consists of a triblock (rinser, filler and capper), self-adhesive labeler and conveyor belts. It is being sold because a new line with a higher capacity has been purchased. It has already been dismantled. Technical Details  Capacity: Max 6,000 b/h Formats: 0.210L, 0.355L, 0.500L glass bottles 26mm metal crown caps Dimensions: Width: 5,300 mm Depth: 2,630 mm Height: 2,860 mm Weight: 8,000 kg POWER SUPPLY: Main: 460V – 60Hz – 3F+N+T Auxiliary: 24V DC Machine main motor: 4 kW Installed power: 9 kW Scope of Delivery  Triblock (rinser, filler, and capper) Selfadhesive Labeller with 2 stations Conveyors Ledpfevm U Dlox Adwsrg

Condition: used, *Available from approx. end of 2025* Fully automatic finger jointing line for the following dimensions: Thickness: approx. 24 – 100 mm Width: approx. 80 – 240 mm Finger jointing length: 400 – 1,500 mm Finished length: 2.50 m – 13.50 m continuously variable Consisting of the following system components: - SMB vacuum destacking lengthwise with 2 lifting tables and 2 package roller conveyors, built in 2013 Package dimensions max. 1.20 x 1.20 x 6.00 m 4 suction pads Sicko system Separation and infeed into roller conveyor for scanner feeding, board turner, switch for too moist, too dry, switch for B-quality, marking station or automatic operation - Bidac end-face scanner for cupping detection, built in 2013 - Brookhuis moisture measurement FMI 5 Year of manufacture 2019 - Microtec scanner Goldeneye 502, year of manufacture 2012 with X-ray, 4 color cameras and new optimization software - Dimter-Opticut 350-2, year of manufacture 2003 with paddle ejector, year of manufacture 2009 and associated sorting belts and pneumatic ejector for 2 additional qualities - NKT packaging - NKT finger jointing system with turntable Spezialpack AH 1050, year of manufacture 2005 consisting of: Milling machine · Tipping station · Threading section length 5.0 m · Cyclic press length 6.00 m · Cross-cut saw - SMB stacking machine, year of manufacture 1998, 2.50 - 13.50 m length, divisible into 2 units (e.g. 2 x 5.0 m) 8 stacking arms, 8 stacking tongues, manually adjustable electro/hydraulic stop, package width: max. 1200 mm, package height: max. 600 mm, hydraulic package pusher Storage location: Customer Lredpfevvi Tyjx Adwog

Condition: used, Year of construction: 2004, Sealing bar length 2500 mm Maximum width of upper reel 2400 mm Maximum width of lower reel 1450 mm Width of conveyor belt 1300 mm Length of entry belt 4800 mm Ljdjwh A Hcepfx Adworg Maximum useful height 800 mm belt speed 5-25 m/min with inverter heat shrink tunnel kw 50

Year of construction: 2020, condition: good (used), FFP2 Mask Production Machine Production Line Manufacturer: Ruhlamat Lrsdpfx Aorm R Hdsdweg Model: MPL FFP2/016 Year of manufacture: 2020 Mask Production Line N95/FFP2 Masks Installation dimensions LxWxH: 8921 x 1494 x 1985 mm Clearance around the machine: 1500 mm all around 50 Hz / 2.6 kVa Pressure: 6 bar Approx. weight: 2500 kg FFP2 masks are made of 3 to 6 layers of nonwoven fabric. This machine can produce masks with up to 6 layers. The system is comprised of five stations: Station 1: Unwinder Station 2: Punching nose clip and embossing roller welding Station 3.1: Printing and welding ear loops Station 3.2: Aligning folding edge Station 4: Contour welding and cutting mask

Condition: excellent (used), Soup production line Lodpfx Ajyc E Rfedwjrg Ready for operation

Condition: excellent (used), Mayonnaise production line. The machine is ready for operation. Lrodpsyc E Nzjfx Adwjg

Condition: excellent (used), Juice extraction line offer: - B-FRU-800 HK press, year 2004 - Grinder / crusher - Pulp pump - Slot filter for water from belt washing - Water pump - Tank with agitator - Juice tub - Flottweg control cabinet - Bin tipper - Apple washer - Apple roller conveyor - Feeder to grinder - Control cabinet - Belt conveyor with cleats All machinery and equipment are made of acid-resistant stainless steel. The quoted price is for the complete set of machines. Ljdpfsyc Eagex Adwjrg

Condition: used, Filling machine: Elopak Type P-M30D Pure-Pak Classic Type P-M30D with screw caps! Capacity: 3,000 pieces/hour Filling volumes: 0.2 - 0.33 - 0.5 L Complete with screw cap Spare parts kit included Machine speed: Maximum 3,000 cartons per hour (mechanical capability), selectable speeds. Standard carton sizes: 200 - 330 - 500 ml More technical details available upon request. Ljdpfx Aoycwc Todworg

Condition: excellent (used), Offer: Juice extraction line: - Flottweg B-FRU-1500 LR press, year 2004 - mill/pulper - apple washing tank - mash pump - box pallet tipper - inclined conveyor to the mill - pomace conveyor - juice cooler - Flottweg control cabinet Ledsyc D N Tjpfx Adworg - juice tank - juice tray - juice pump (x2) - slot filter for belt washing water - water pump - vibrating filter - pulp pump - citric acid tank - secondary water tank - water tank (x2) - pump and valve station - process cabinet All machines and equipment are made of acid-resistant stainless steel. The price is for the complete set of machines.

Condition: new, functionality: fully functional, Year of construction: 2025, control type: CNC control, degree of automation: automatic, actuation type: electric, laser type: fiber laser, laser source manufacturer: MAX Photonics, laser power: 1,500 W, sheet thickness steel (max.): 15 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 6 mm, sheet thickness brass (max.): 4 mm, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, compressed air connection: 8 bar, overall weight: 2,800 kg, Equipment: CE marking, centralized greasing system, cooling unit, dust extraction, emergency stop, fume extraction, safety light barrier, Laser cutting machine with 3 kW fiber laser Our goal is to offer highly precise, long-term stable, and yet affordable laser machines. Our machines are ideal for workshops and repair businesses. A perfectly developed cutting parameter library is included in delivery, as is first-class service. The ultra-affordable entry into laser cutting technology - High-quality MaxPhotonics laser source - Extremely energy-efficient cutting system - Requires only approx. 3.0 x 3.0 meters of installation space - Top quality, book a viewing appointment now! Cutting capacity: Lrsdpfx Aoyacw Rjdwsg - Steel sheet up to 22 mm - Stainless steel sheet up to 12 mm - Aluminum sheet up to 8 mm - Travel range approx. 1300 x 1300 mm - Table size: approx. 1300 x 2500 mm (fits a full medium-format sheet) - German-language machine control - Manual front door - Comprehensive collision protection measures - Large front window for cutting process observation - Automatic, programmable 2-gas switching (compressed air/nitrogen, oxygen) - Extensive cutting parameter database - Incl. nesting module - Very easy to operate - Powerful laser chiller Sales are exclusively to commercial customers. Delivery / consultation / sales only in Germany / Austria / Switzerland. Approximate machine dimensions: Width: 3.2 m Height: 2.3 m Length: 3.3 m Total weight: approx. 3,000 kg Leasing or hire purchase is available through our financial partner. Need a different laser power, table type, or table size? No problem. I am happy to prepare a tailored offer. Not sure which laser power is right for your application? I will of course carry out cutting trials according to your requirements. Anything is possible—from 0.5 kW up to 20 kW laser power.

Condition: new, functionality: fully functional, Year of construction: 2025, control type: CNC control, degree of automation: automatic, actuation type: electric, laser type: fiber laser, laser source manufacturer: MAX Photonics, laser hours: 10 h, laser power: 3,000 W, laser wavelength: 1,070 nm, sheet thickness steel (max.): 22 mm, sheet thickness stainless steel (max.): 12 mm, sheet thickness aluminum (max.): 12 mm, sheet thickness brass (max.): 5 mm, table length: 2,070 mm, table width: 1,070 mm, working length: 2,000 mm, working width: 1,000 mm, travel distance X-axis: 2,000 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 100 mm, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, warranty duration: 12 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, Offered here is a high-precision laser cutting machine with 3000 watts of laser power Type: LG-1020/3kW HaiCut Premium Line - Fully equipped - Innovative 3-gas switching system (pressure and gas type controllable through software) Cutting with N2, O2, or mixed gas (compressed air) - Automatic front door - Machine bed lined with fireclay - Machine bed and axes measured and calibrated with Renishaw interferometer Our goal is to offer the best, most reliable, and cost-effective laser machines currently available on the market. Our machines are ideal for workshops and repair operations. A perfectly developed cutting parameter library is included, as well as first-class on-site support. Lodpfxjyacwke Adworg Brand new machine, delivery time approx. 6–8 weeks We would be pleased to demonstrate the machine at our facility. Traverse path: approx. 1000 x 2000 mm Table surface: approx. 2070 x 1070 mm (accommodates a small format sheet inside the machine) Pull-out cutting table For ultra-precise metal cutting Fully installed and calibrated Cutting software in German Incl. nesting module Very easy to operate Switch on and start working Laser source by Max Photonics (G5/German version) with 3000 watts output Extensive electronic and mechanical collision protection for the cutting head Large laser safety window on the front door Automatic front door Safety light curtain for maximum operator protection Cuts stainless steel up to 12 mm Cuts steel up to 22 mm Cuts aluminum up to 12 mm Cuts brass up to 5 mm Heavy-duty industrial quality Complete system / ready to use LED work area lighting 200 mm duct connection for fume extraction Incl. extraction fan Leasing or hire purchase available via our financing partner Need a different power rating or table size? No problem—we have various machines in stock or available at short notice. Sale to commercial customers only. Delivery, consulting, and sales only in Germany, Austria, and Switzerland Machine dimensions (approx.): Width: 2.9 m, Height: 2.1 m, Depth: 3.3 m Weight: approx. 2.5 tons

Condition: new, functionality: fully functional, Year of construction: 2025, control type: CNC control, degree of automation: automatic, actuation type: electric, laser type: fiber laser, laser source manufacturer: MAX Photonics, laser power: 3,000 W, laser wavelength: 1,070 nm, sheet thickness steel (max.): 22 mm, sheet thickness stainless steel (max.): 12 mm, sheet thickness aluminum (max.): 10 mm, travel distance X-axis: 3,050 mm, travel distance Y-axis: 1,550 mm, travel distance Z-axis: 120 mm, input voltage: 400 V, type of cooling: water, overall weight: 3,500 kg, door opening width: 3,000 mm, door opening height: 600 mm, Equipment: CE marking, cabin, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, New laser cutting machine with 3kW fiber laser Delivery time approx. 8 weeks Our commitment is to offer highly precise, long-term stable, and yet cost-effective laser machines. Our machines are ideal for workshops and repair shops. A thoroughly developed cutting parameter library is included as well as exceptional service. - Includes 2D bevel-cut function for weld seam preparation or production of countersunk holes (see image) - Machine without automatic shuttle table! Loading is carried out from the long side of the machine - Very space-saving - Extremely energy-efficient cutting system - Requires only approx. 4 x 4.5 meters floor space - 3kW laser source by MaxPhotonics (G5/German version) - Laser generator with socket efficiency better than 30% - Suitable for aluminum - Top quality, schedule a viewing now! Cutting capacity: - Steel up to 22mm (max.) - Stainless steel up to 12mm (max.) Ljdpfx Aoyacqwodwjrg - Aluminum up to 10mm (max.) - Brass up to 8mm (max.) - Travel range 1500 x 3000mm (for large formats) - Machine control in German - Safety light curtain for maximum operator protection - Extensive collision protection for the cutting head - Large laser protection windows for monitoring the cutting process - Comprehensive cutting parameter file - Includes nesting module - Very easy to operate - Powerful laser chiller - German language machine control - German service and spare parts supply - Powerful laser chiller - Optional filter extraction system available (5.5kW with frequency converter for pleasantly quiet operation) Leasing or hire purchase possible through our financing partner Sale exclusively to commercial customers. Delivery / consulting / sales only in Germany / Austria / Switzerland Approx. machine dimensions: Length: 4.0 m Height: 2.3 m Width: 4.5 m Total weight: approx. 4500 kg Need a different laser power, table type or table size? No problem. I'll gladly provide a suitable offer. E.g. 2kW machine from 29,990 EUR Not sure which laser power is suitable for your application? Of course, I will carry out cutting tests according to your requirements. A lot is possible here.

Condition: good (used), Year of construction: 2001, In good technical condition and fully operational. Manufacturer: Rollsett Machine Oy Finland. Year of manufacture: 2001. Profile height: 18 mm. Entry width: 1,250 mm. Overall width: 1,146 mm; 1,166 mm. Construction width: 1,100 mm. Min./max. length: 0.5 lm/8 lm at a thickness of 0.50 mm. Accessories, aids: screws, sealing tapes, profiled seals, anti-condensation treatment, light profiles. Lodpfxjx Tf Ito Adworg

Condition: good (used), In good technical condition and fully operational. Lrjdpjx Tf Hcofx Adweg Manufacturer: Bud Masz M. Stachlewski Steel thickness – 0.5-1 mm. Profile height: 40 mm. Entry width: 1250 mm. Overall width: 944 mm. Effective width: 915 mm. Min./max. length at a thickness of 0.5 lm/12 lm starting from a thickness of 0.75 mm Accessories, auxiliaries: screws, sealing tapes, profiled gaskets, anti-condensation treatment, light-transmitting profiles

Condition: ready for operation (used), Year of construction: 2012, product length (max.): 2,250 mm, This Hüttenhölscher Line multi-spindle drilling machine was manufactured in 2012. It features a PC-controlled function sequence under Windows 7 with TwinCAT, a 6-station loading gantry, and a 2-axis gantry robot. The machine includes a vacuum generation by ejector and multiple conveyor lines for efficient material handling. Ideal for high precision drilling with its advanced control system. Contact us for more information about this machine. • Control: PC-controlled function sequence under Windows 7, TwinCAT • Part dimensions: • Length: 300–2250 mm • Width: 350–710 mm • Thickness: 16–25 mm • 2-station drilling station: • Base frame as welded construction with machined screw-on surfaces • 2x toothed belt conveyors V = 1.5 m/sec • 2x pneumatic lift for toothed belt conveyors • 2x stoppers for cabinet parts, dampened by shock absorbers • 2x pneumatic double clamping cylinders, controlled by ball screw and servo motor, moved to side height (measuring the side height) • 2x pneumatic cross alignment ruler (plausibility check) • 2x vacuum clamping units in the drilling machine table • 2x 0-line controllable • Support: • Support can be moved in the X direction by means of a servomotor • 2x drilling gear (support 1): • Support equipped with 2 units (machining from above) • Individually movable in Y direction by servomotor • Individually movable in Z direction by servomotor • Drilling gear a = 32 mm, adjustable with frequency converter, drill chuck Ø 10h7 with grub screw • Callable spindles, 8000 rpm • Two 16-spindle drilling gears • Groove saw (support 1): • Sawing units for cutting special rear wall grooves • Sawing unit with tool holder, speed control via frequency converter • Pneumatically pilot-controlled working position • 2x milling spindles right/left at the front edge (support 1): • Pneumatically pilot-controlled working position Additional equipment (automation, handling, guarding, conveyors) • Loading/handling: • 6-station loading gantry • 2-axis gantry robot; Y/Z axes with servo motors; travel distances: Y-axis 8500 mm, Z-axis 1500 mm Lrodpfx Aeyctaujdwsg • Suction crossbeam with four-circuit vacuum supply; vacuum generation by ejector • Double part detection • Portal supports • 4 stacking stations • 1 hand rest station (automatic/manual feeding) • 1 removal station (automatic/manual removal) • Side feed range: • Stack height: max. 1000 mm (60 parts) incl. protective plate • Protective plate sizes: • 1380 mm x 780 mm • 1220 mm x 720 mm • 1120 mm x 620 mm • 2290 mm x 620 mm • Thickness: 25 mm • Thickness: max. 28 kg • Floor roller conveyor / stack feed: • 4 roller conveyor lines, 930 mm wide x 3600 mm long, AH 300 mm • Feeding/removal: manual cross transfer carriage • Support stations / automatic feeding: • Transport section 950 mm wide x 4100 mm long; integrated side stop • Manual feeding: • Toothed belt section 900 mm wide x 2500 mm long • Transfer shuttle: • Toothed belt section 900 mm wide x 2500 mm long; horizontal stroke approx. 2500 mm by three-phase motor • Return: • Transport section 950 mm wide x 4000 mm long; pneumatic stopper • 90° rotary unit: • Vacuum suction cup; pneumatic stroke; rotation by three-phase motor by +/- 90° • Discharge stations / automatic removal: • Transport 950 mm wide x 3000 mm long; positioning of cabinet parts by encoder • Manual removal: • Toothed belt section 900 mm wide x 3000 mm long • Protective system for feeding: • 45 m protective fence with 3 access doors

Condition: excellent (used), The line includes: - three stone removers - a roller grader - a pit scraper - a screw conveyor for pits Lrodpoycqbiofx Adwsg The machines have only worked for three seasons and are in very good condition. The price refers to all machines.

Condition: new, Year of construction: 2026, functionality: fully functional, Edge banding machine – NB860EC - Machine with 6 edge band magazines and servo feed • Robust machine structure and most of the machine's mechanical parts are machined with advanced CNC machines for greater stability and longer life without deformation; • Combines multiple functions in one machine, including pre-milling, pre-heating, pre-melting, end trimming, servo fine cutting, servo scraping, surface scraping and polishing, spraying, all in one process. • Intelligent PC control, feed guide, belt pressing rollers, fine cutting and scraping are controlled by a servo motor. Corner rounding is adjusted pneumatically. Machine speed 16/20/24 m/min; • Nesting kit design • Fine refilling and corner rounding via HSK25 TECHNICAL DATA Panel length: ≥120 mm; ≥200 mm with rounded corners Panel width: ≥60 mm Min. Panel size: 120× 120mm; 120× 60mm long edge; 200*80 mm short edge Panel thickness: 9-60 mm Thickness C=edge: 0.4-3 mm Feed speed: 16/20/24 m/min Power supply: 380 V; 50 Hz Required air pressure: 0.7 MPa Distance between panels ≥50 Console 2 Dust collection outlet Φ 125 mm*5 Total power: 28 Kw Approximate weight: 3,000 kg Overall dimensions: 5,930*1,050*1,850 mm Lodsx Uplxopfx Adwjrg 6-sided drilling CNC and double workstation ND712DTL The ND712D is designed to have 2 independent workstations of 1200+650 mm, integrating 2 machines into one, thus doubling efficiency with less space required. The integrated, high-rigidity machine body structure gives the entire machine a longer service life and fast, stable machining. The optimized drill layout makes drilling more efficient. TECHNICAL DATA Total power: 52.36 kW Machine size: 7400 * 4,620 * 2,650 mm Power supply: 380V/50Hz 3 phases Air supply: 0.6-0.7MPa Total weight: 7,850 kg Control system: SYNTEC Panel size: Length: 250-2,800 mm / Width: 250-650/1200 mm / Thickness 10-60 mm Maximum travel speed: ( X) Axis /U ) - 135 m/min Y axis - 75 m/min Z axis - 30 m/min Transmission mode X axis - Rack and pinion Y axis - Rack and pinion Z axis - Ball screw Drilling blocks: Top 2+2; Bottom 1+1 Vertical drills (top): 19*4 Horizontal drills (top): X: 3 × 8 + Y: 2 × 8 Vertical drills (bottom): 9 × 2 Maximum drilling diameter: Φ35mm Distance between holes: 32 mm Rotation speed: 5000 rpm Shank diameter: Φ10mm Main shaft: 4* ER25 Power: 2*3.5kw; 2*5.5kw max. 18000rpm

Condition: new, functionality: fully functional, Offered for sale is a semi-moist pet treat production equipment set based on a twin-screw extruder, designed for continuous forming, portioning, and cooling of semi-moist products. The line has been dismantled and is ready for shipment. It was purchased from a supplier and not used in production, but the configuration is equivalent to machinery currently operating in active plants for semi-moist pet treat manufacturing. This system addresses the key process steps that define semi-moist product quality and handling: stable solids dosing into the extruder, controlled shaping and cutting, as well as staged cooling to stabilize texture and reduce sticking or deformation before packaging or further processing. The extruder is of twin-screw design and has achieved production capacities of up to 150 kg/h, depending on recipe and configuration. Product shaping is highly flexible and can be adapted to a variety of product formats; it is suitable for dental sticks, hearts, bones, sticks, strips, and other geometries depending on the die/forming set and cutter configuration. The configuration line has been used for high meat meal or grain-free semi-moist treats as well as vegetarian-type items; final product characteristics depend on recipe, moisture targets, and process parameters. Dry base components are supplied using a volumetric or mass-based dosing feeder, feeding directly into the extruder. This enables steady extrusion and consistent shaping. Downstream portioning is performed with a rotary knife cutter fitted with specialized inserts for clean cutting of semi-moist products. Cut length can start from approx. 5 mm and can be adjusted as required; achievable range depends on settings and the cutter head. The cutter head concept is flexible and can be adapted or redesigned depending on desired final product and surface finish for different shapes and recipes. Lodpfsycfw Eox Adwjrg After forming and cutting, product is conveyed through an initial cooling section with a fan, followed by a conveyor cooler for further stabilization. Cooling is based on ambient forced air, with cooling performance managed by conveyor speed (residence time) and airflow. This two-stage cooling process is optimal for semi-moist products, helping to prevent clumping, deformation, or marking during handling and transport. A notable feature of this line is the mixing head at the extruder outlet, which supports improved mixing and temperature control and enables production of two-color treats (application dependent). The sale also includes the liquid handling package used in semi-moist processing—stainless steel pumps and tanks for water, fats/oils, glycerol, and other typical process fluids. All liquid handling components are stainless steel, meeting hygienic production standards.

Condition: like new (used), Year of construction: 2022, As-new condition (only 5,000 m² of parquet processed so far), compact oil application line consisting of: Roller Application Unit: - For the application of oils, etc. - Touchscreen control - Manual height adjustment - Max. working width: 300 mm - Max. workpiece height: 50 mm - Membrane pump with max. capacity of 18 l/min - Frequency inverter for variable speed of application roller - Frequency inverter for variable speed of counter-roller - Conveyor belt speed adjustable: 3 to 14 m/min - Stainless steel recovery trays Pad Group + Brush Group: - For spreading and removing excess oils - Touchscreen control - Manual height adjustment - Conveyor belt speed adjustable: 3 to 14 m/min - Max. working width: 300 mm - Max. workpiece height: 50 mm - Pad diameter: 300 mm Lredpjx Ah A Asfx Adwog - Quick-change system for pads - Brush dimensions (L x D): 300 x 160 mm - Quick-change system for brushes UV / LED Unit: - Touchscreen control - Manual height adjustment - Max. working width: 300 mm - Max. workpiece height: 50 mm - UV-LED power: 12 Watt/cm² - Incl. ventilation fan - Conveyor belt made of Kevlar fabric - Conveyor belt speed adjustable: 3 to 14 m/min Outfeed Conveyor Belt: - Length: approx. 2,500 mm - Max. working width: 300 mm - Conveyor belt speed adjustable: 3 to 14 m/min Note for used machinery: • Technical details and prior sale subject to change and errors. • Stated prices are ex works - free loading! • The machine has been cleaned and functionally tested. • All machines are sold as inspected, without any warranty claims. Buyers are free to inspect the machine at its location. • Special agreements are only valid in written form. (We only respond to enquiries with your address and telephone number!)

Condition: used, Year of construction: 2010, Overview This PET filling line was manufactured between 1996 - 2019 by several European manufacturer. The line is designed for carbonated beverages such as lemonades and also suitable for water with or without CO₂. With an output capacity of 14.000 bph, it offers a complete solution from bottle blowing to palletizing. This equipment is in good condition and still fully operational.   Technical Data Capacity: 14.000 bph Filling product: carbonated water and soft drinks  OPP wrap-around label from a reel with hotmelt and glue labelling station Packaging formats: shrink wrapping without tray Pallet: Euro pallet (1.200 x 800 mm)  condition: good technical condition, still in production Scope of Delivery Blow moulding machine | Sidel | SBO10 | 2010 Elevator preform | Sidel | 2010                                                                                                                    Air conveyors | Sidel-Alsim | 1999 Rinsing/Filling/Capping | Sidel-Alsim | 48/60/10 | 1999                                                                                           Mixer | Sidel-Alsim | 1999 Bottle dryer | ACI | 2015 Labelling machine | Krones Contiroll | 2004 Shrink wrapping machine | Acmi | 2019 Handle applictaor | SMI-Pack | 2002 Conveyors for bottles and trays | Sidel-Alsim | 1999 Palletizer | Alsim | 1996                                                                                                                                                Pallet wrapper | PM Pragometal #1 | 2009 Pallet wrapper | PM Pragometal #2 | 2009 Lrsdpfx Asyb Tuiedweg

Condition: used, Year of construction: 2003, Overview This complete filling line for non-returnable glass bottles was manufactured 2003 by several well-known European producers, mainly Sidel. The line is designed for high-capacity beverage production, handling up to 40,000 b/h and is in a good condition and designed for 3-shift 24/7 operation.  Technical Data Capacity: 40,000 bph (at 0,25L) Bottle Formats: 0.25L, 0.33L, 0,5L Packaging formats: • 4x6 x 25cl • 1x12 x 25cl • 24x25cl • 24x30cl • 4x6 x 33cl • 6x4 x 33cl • 1x12 x 33cl •24x33cl • 20x50cl  Application: beer, CSD, or other beverages in non-returnable glass bottles Hygienic design Automated change-over  Scope of Delivery Pallet Transport (Depalletiser) | Sidel / SIG Simonazzi / GEBO | 2003 | SWEEP-OFF/B Bulk Depalletiser | Sidel / SIG Simonazzi / GEBO | 2003 | SWEEP-OFF/B  Pallet Transport (Palletiser) | Sidel / SIG Simonazzi | 2003 | LINEAR Tray and/or Carton Palletiser | Sidel / SIG Simonazzi | 2003 | LINEAR Pallet Shrinkwrapper | Sidel / SIG Simonazzi / MSK | 2003 | ECONOTECH/TOWERTECH Pallet Labeller | Sidel / SIG Simonazzi / Logopak | 2003 | LOGOMATIC 920 II PF Basket Erector | Sidel / SIG Simonazzi / H&B Schleuter | 2003 | TLA Fourpack Transport and Divider | Sidel / SIG Simonazzi / H&B Schleuter | 2003 | TLW Basket Inserter | Sidel / SIG Simonazzi / H&B Schleuter | 2003 | TLE Carton Packer | Sidel / SIG Simonazzi / FANUC | 2003 | ROBOKOMBI Carton Closer | Sidel / SIG Simonazzi / Bortolin | 2003 | MARA H.M Carton Marker 1 | Sidel / SIG Simonazzi / Domino | 2003 | A-Serie Inkjet Printer Carton Marker 2 | Sidel / SIG Simonazzi / Domino | 2003 | A-Serie Inkjet Printer Weight Checker | Prisma | 2003 | 10D3 Full Carton Inspection | BBull / Centro Kontrollsysteme | 2015 | Image VKK 500 Bottle Conveyors | Sidel / SIG Simonazzi | 2003 | TRANSPORT Carton Conveyors | Sidel / SIG Simonazzi | 2003 | TRANSPORT Crown Cork Feeder | Sidel / SIG Simonazzi | 2003 | SM80 Rinser | Sidel / SIG Simonazzi | 2003 | EUROTRONICA LP Filler | Sidel / SIG Simonazzi | 2003 | EUROTRONICA LP Crowner | Sidel / SIG Simonazzi | 2003 | EUROTRONICA LP C.I.P. | Sidel / SIG Simonazzi | 2003 | AUTOSAN Fill Height Control | Sidel / SIG Simonazzi / Heuft | 2003 | SPECTRUM TX Tunnel/Bottle Pasteuriser | Sidel / SIG Simonazzi | 2003 | PAMA CLD 50/144 Bottle Coding on Necklabel | Mundi-Technology | 2015 | Mundiscan UP2000 HE Labeller | Sidel / SIG Simonazzi / Krones | 2003 | Topmodule Type 407 Bottle Inspection & Sorting | Sidel / SIG Simonazzi / Krones | 2003 | Checkmat type 707 Tap tone | Sidel / SIG Simonazzi / Krones | 2003 | TapTone 500 Series Ljdpfx Adjyb Tucjworg

Condition: used, Year of construction: 2014, Overview  This complete glass bottling line was manufactured between 2010 and 2014 by several reputable European manufacturers, including CIMEC (Italy). The main monobloc — a CIMEC 16-16-1 rinsing, filling and crowning unit — was built in 2014 and operated at a natural mineral water facility until July 2025. The line also includes auxiliary equipment such as self-adhesive and wrap-around labellers, a DE filter, and a heat-shrink capsule tunnel, making it a fully functional and compact filling line for glass bottles with crown caps. All equipment remains installed, is in good condition, and can be inspected on site. Technical data  Year of Manufacture: 2010–2014 Application: Water and other beverages Capacity: Approx. 2,000 bph (330 ml) Approx. 1,670 bph (500 ml) Bottle Formats: 250 ml – 1,000 ml (included: 330 ml & 500 ml) Closure Type: 26 mm crown caps Configuration (Monobloc): 16 rinsing heads 16 filling heads 1 crowning head Scope of Delivery  Rinser / Filler / Crowner Monoblock | CIMEC | Monobloc 16-16-1 | 2014 | 16/16/1 configuration, 26 mm crown caps, 2,000 bph Self-adhesive labeler | Canellitech | V500 | 2012 | Linear, up to 3. 500 bph Single-head labeler (wrap-around) | Identapply | Servo 125 RH | 2010 | With conveyor belts DE filter | Spadoni | - | 2011 | 80 hl/h Shrink tunnel | TOSA | TN1 | 2011 | For PVC capsules   Lrodpfjyb Tkdox Adweg

Condition: used, Year of construction: 2016, Overview  This fully automatic packaging system for jars was built by Buhmann pac solutions System GmbH in 2016 and has been used very little, with only approx. 5,000 operating hours (of which approx. 2,000 hours were in pure production operation). The line includes a carton erector (wrap-around trays) and a packing unit and, in addition to packaging single-type cartons, also offers the option of automatically mixing offline products (mixed cartons). The system was regularly maintained by Buhmann & Yaskawa, with around €200,000 invested in maintenance and servicing between 2020 and 2024. The system is in very good condition and is available immediately. Technical details  Performance Product infeed online: max. 280 jars/min Format 3: max. 220 jars/min Mix type A: max. 140 jars/min (11.5 cartons/min) Mix type B: max. 140 jars/min (11.5 cartons/min) Total output: max. 350 jars/min or 30 cartons/min Carton erector & lidder: 23.5 cartons/min Changeover time Format change: approx. 15 minutes Formats / packaging specifications Format 1: 12-jar tray, 2 layers, 350 g jars Format 2: 6-pack tray, 2 layers, 720 g jars Format 3: 6-pack tray, 2 layers, 580 g jars Format 4: 6-pack tray, 2 layers, 1,000 g jars Format 5 (mixed formation): Combination of different jars, automatic mixing via separate belts Operating hours: approx. 5,000 (of which approx. 2,000 are pure production) Power supply Electrical: 3x 400 V / N / PE, 50 Hz Pneumatic: min. 6 bar – max. 12 bar, oil-free, residual oil content max. 0.1 mg/m³ (ISO 8573-1 Class 2) System components Buhmann C300 carton erector (wrap-around trays) Buhmann PF800 packing unit Yaskawa robot with gripping units 2x Nordson PROBlue 4 gluing devices Separate feed belt for offline products (mixed cartons) Carton sealing unit Lrjdpfxeyb Snbs Adwog

Condition: used, Year of construction: 2014, Overview  This fill level and closure inspection unit was manufactured in 2014 by the German company Krones AG. The Krones Checkmat 731 was used for overfill and underfill detection based on high-frequency (HF) measurement as well as closure control for metal caps via sensor technology integrated into the filler. The system was recently dismantled in full working condition after being replaced by a newer camera-based inspection system. All peripheral components such as trigger light barriers, encoder, and pusher were properly disconnected and are included in the delivery. Technical data Inspection functions: Overfill and underfill detection using HF (high-frequency) method Closure control via integrated sensor for metal caps (mounted in filler) Condition: Excellent, fully functional before dismantling Status: Dismantled and stored, ready for shipment Application: Bottling lines for beverages with metal closures Included components: Trigger sensors, encoder, and pusher Ledpfx Adjyb Sk Nswerg