Used Hydraulic Plate Shear for sale (25,207)

Condition: used, Technical details: sheet width: 1500 mm plate thickness: 2,25 mm distance between columns: 1600 mm back gauge: nein cutting angle: nicht bekannt ° cutting gap adjustment: nein mm down holder: über Druckleiste Stück height over floor: 850 mm Table dimensions: LXB 1800 x 350 mm weight of the machine ca.: 0,85 t dimensions of machine: 2,0 x 0,8 x 1,3 m simple mechanical guillotine shear Kedju Icn Ejpfx Adwsll with shelf right/left 305 x 100mm operation via ON/OFF *

Condition: used, Year of construction: 1992, Technical details: sheet width: 3000 mm plate thickness: 2,0 mm distance between columns: 3300 mm back gauge: 580 manuell mm Kedpfx Aou Icnrsdwsll cutting angle: Nein ° cutting gap adjustment: Nein mm down holder: 13 Stück Table dimensions: 3300 x 300 mm weight of the machine ca.: 3,0 t dimensions of machine: 3,7 x 1,5 x 1,8 m incl. 2x upper knife and 2x lower knife each 1500mm incl. table supports 1500 x 1500mm with roller elements 2x profile strips L: 1400mm 1x side stop bar 1600mm operation via control panel and/or foot pedal *

Condition: good (used), Year of construction: 1992, Reinforcing steel shear, reinforcing steel cutting machine, construction steel shear, profile shear, punch, punching machine -Reinforced steel shear: hydraulic -Number of rods: Ø 12mm/8 pieces, Ø 16mm/4 pieces, Ø 35mm/1 piece -Foot switch: 1 Ksdpfx Ajx Srlpsdwoll -Dimensions: 1230/680/H640 mm -Weight: 419 kg

Year of construction: 2000, condition: ready for operation (used), A hydraulic guillotine shear Turi is available. Cutting length: 2500mm, max. material thickness: 4mm, backgauge: 600mm, stroke rate: 20/min. Machine dimensions X/Y/Z: approx. 3300mm/1500mm/1500mm, weight: approx. 4000kg. Documentation available. An on site inspection is possible. Kljdpfjyb Scxex Adwjl

Condition: like new (used), Year of construction: 2018, sheet width 2050 mm plate thickness 3.0 mm distance between columns 2100 mm back stop - adjustable 550 mm no. of strokes 35 Hub/min cutting angle 2°12 table width 400 mm table height 850 mm Control konv. total power requirement 3.5 kW weight of the machine ca. 1280 kg dimensions of the machine ca. 2400 x 1500 x 1300 mm Current new price approx. 20.000 Euro from a maintenance workshop very little used - mint condition (!!) - in checked conditions - machinevideo - Klodjx Sr Dxjpfx Adwjl ?v=tUyx7mR0vp4 Equipment: - robust / powerful electro-mechanical guillotine shears - manual material backgauge * stepless adjustment range * adjustment from behind - by handwheel * including mm scale * max. adjustment range 550 mm - Manual kerf adjustment, from the front - 1x side stop - 1x support arms - 1x free-moving foot switch - rear sheet metal chute - rear safety device (light barrier) - Operating instructions (machine control)

Condition: new, Year of construction: 2025, control type: CNC control, actuation type: hydraulic, working width: 3,100 mm, cutting angle (min.): 0.5 °, cutting angle (max.): 2 °, stroke rate (min.): 15 1/min, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, STANDARD FEATURES Ksdpfx Aox Nqp Iodwsll CNC-controlled, angle-adjustable hydraulic guillotine shear CNC-controlled blade gap, stroke, and cutting angle adjustment Touchscreen CNC control unit (ELGO P40T) Automatic cutting angle adjustment based on material type and thickness Automatic stroke shortening for short sheet cuts (higher speed) CNC software infrastructure to minimize user errors Stress-relieved, heavy-duty steel welded frame Hardened guides and roller-guided upper table movement system 1,000 mm CNC-controlled, motorized and programmable backgauge Backgauge features: - Programmable retract function - Lifting feature for long workpieces - ±0.1 mm positioning accuracy Ball screw sheet support front table Top blade: 2 cutting edges / Bottom blade: 4 cutting edges High-alloy steel blades Special linkage system reducing maintenance needs Front support arms with ruler, T-slot, and stopper (1,000 mm) Cutting line illumination and shadow wire Front finger guard sheet (openable type) Front and side safety covers Foot pedal Movable control lever Emergency stop buttons Safety equipment compliant with CE standards OPTIONAL FEATURES Rear pneumatic sheet support system – Type 1 Rear pneumatic sheet support system – Type 2 (with front feeding function) Angle-adjustable front gauge (0–180°) Custom-length front support arms Full-length openable front finger guard cover Front finger safety light curtain Rear safety light barrier (CE compliant) Special blade options Laser cutting line Oil heater or oil cooler Automatic or manual centralized lubrication system Electrical cabinet air conditioning system CNC-controlled front sheet support and feeding arms Special throat depth (500 mm) Lightweight safety covers TECHNICAL SPECIFICATIONS (MODEL C 06 / 3100) Cutting capacity (450 N/mm²): 6 mm Cutting capacity (700 N/mm²): 4 mm Cutting length: 3,100 mm Cutting angle: 0.5° – 2° (CNC-controlled) Cutting stroke: automatically adjusted Throat depth: 250 mm Backgauge movement range (X axis): 1,000 mm Cutting speed: 10 – 15 strokes/min Motor power: 10 kW Oil tank capacity: 200 L Machine weight: ~6.7 tons Machine dimensions (LxWxH): approximately 4,830 x 2,995 x 1,975 mm

Condition: new, Year of construction: 2025, control type: CNC control, actuation type: hydraulic, working width: 4,000 mm, cutting angle (min.): 0.5 °, cutting angle (max.): 3 °, stroke rate (min.): 12 1/min, sheet thickness (max.): 10 mm, sheet thickness steel (max.): 10 mm, STANDARD FEATURES CNC-controlled, angle-adjustable hydraulic guillotine shear CNC-controlled blade gap adjustment, stroke and cutting angle adjustment Touchscreen CNC control unit (ELGO P40T) Automatic cutting angle adjustment (according to material type and thickness) Automatic stroke reduction feature (increased speed for short cuts) High-precision, stress-relieved steel frame Hardened guides and roller-equipped upper table movement system 1,000 mm CNC-controlled, motorized, and programmable backgauge Backgauge features: - Programmable retraction - Raising function for long sheets - ±0.1 mm positioning accuracy Ball support front table for sheet feeding Upper blade: 2 cutting edges / Lower blade: 4 cutting edges High-alloy steel blades Special joint system requiring minimal maintenance Front squaring arms with scale, T-slot, and adjustable stopper (1,000 mm) Cutting line illumination and shadow wire Front finger guard plate (openable type) Front and side safety covers Foot pedal Movable control lever Emergency stop buttons Safety equipment in compliance with CE standards OPTIONAL FEATURES Rear pneumatic sheet support system – Type 1 Rear pneumatic sheet support system – Type 2 (with sheet return function) Angle-adjustable front gauge (0–180°) Front squaring arms in custom lengths Full-length openable front finger guard cover Front finger safety light curtain Rear safety light barrier (CE-compliant) Special blade options Laser cutting line Oil heater or oil cooler Automatic or manual central lubrication system Electric cabinet cooling system (air-conditioned) CNC-controlled front sheet support and feeding arms Special throat depth (500 mm) Kedpfx Adjx Nqphewjll Light-duty guarding TECHNICAL SPECIFICATIONS (C 10 / 4000 MODEL) Cutting capacity (450 N/mm²): 10 mm Cutting capacity (700 N/mm²): 6 mm Cutting length: 4,000 mm Cutting angle: 0.5° – 3° (CNC-controlled) Cutting stroke: Automatically adjustable Throat depth: 250 mm Backgauge movement range (X axis): 1,000 mm Cutting speed: 6 – 12 strokes/min Motor power: 22 kW Oil tank capacity: 300 liters Machine weight: ~16 tons Machine dimensions (LxWxH): approx. 5,790 x 3,650 x 2,580 mm

Condition: new, Year of construction: 2025, control type: CNC control, actuation type: hydraulic, working width: 4,000 mm, cutting angle (min.): 0.5 °, cutting angle (max.): 3 °, stroke rate (min.): 12 1/min, sheet thickness (max.): 16 mm, sheet thickness steel (max.): 16 mm, Standard Features • ELGO P40T Touch NC Control Unit • Rexroth / Hoerbiger hydraulic system • Automatic CNC-controlled blade clearance, stroke, and blade angle adjustment • 1,000 mm NC-controlled, programmable, motorized backgauge • 250 mm throat depth • Programmable backgauge retraction movement • Backgauge lifting function for sheets longer than 1,000 mm • Adjustable cutting length via control panel for increased stroke rate in short cuts • Ball transfer sheet support table • Upper blade with 2 cutting edges / lower blade with 4 cutting edges • Special pivot system to reduce maintenance needs • 1,000 mm front support arms with ruler, T-slots, and stopper • Front and side safety guards • Cutting line illumination and shadow wire • 1,000 mm front finger guard with openable cover • Foot pedal • Movable control lever and safety cabinets • Emergency stop buttons Optional Features • Rear pneumatic sheet support system (Type 1) • Rear pneumatic sheet support system with sheet return to the front (Type 2) • Angle-adjustable squaring arm 0–180º • Front support arms of custom lengths • Special throat depth of 500 mm • Full-length openable front finger guard cover • Front finger protection safety light curtain • Special blades • Laser cutting line indicator • Oil heater or oil cooler • Automatic or manual centralized lubrication • Electrical cabinet air conditioning cooling • CNC-controlled front sheet support arms • CE-compliant rear light barrier • Lightweight safety guards TECHNICAL SPECIFICATIONS VALUE Cutting Capacity (450 N/mm²) 16 mm Cutting Capacity (700 N/mm²) 10 mm Cutting Length 4,000 mm Cutting Angle 0.5 – 3° Cutting Speed / Fast Mode 6 / 12 spm Throat Depth 250 mm Backgauge Travel (X) 1,000 mm Table Length Table Width Motor Power 30 kW Klodpsx Npd Rofx Adwel Weight 21.5 tons

Condition: new, Year of construction: 2025, control type: CNC control, actuation type: hydraulic, working width: 3,100 mm, cutting angle (min.): 0.5 °, cutting angle (max.): 3 °, stroke rate (min.): 13 1/min, sheet thickness (max.): 10 mm, sheet thickness steel (max.): 10 mm, Standard Features • ELGO P40T Touchscreen NC Control Unit • Rexroth / Hoerbiger hydraulic system • Automatic CNC-controlled blade clearance, stroke, and blade angle adjustment • 1,000 mm NC-controlled, programmable, motorized backgauge • 250 mm throat depth • Programmable backgauge retract function • Backgauge lifting feature for parts longer than 1,000 mm • Adjustable cutting length via control panel to increase the number of cuts for short workpieces • Ball transfer sheet support table • 2 cutting edges on upper blade / 4 cutting edges on lower blade • Special joint system to reduce maintenance requirements Kedpfx Asx Npddjdwoll • 1,000 mm front support arms with ruler, T-slot, and stopper • Front and side safety guards • Cutting line illumination and shadow wire • 1,000 mm front finger guard with openable cover • Foot pedal • Movable control lever and enclosure cabinets • Emergency stop buttons Optional Features • Rear pneumatic sheet support system (Type 1) • Rear pneumatic sheet support system with forward delivery (Type 2) • Miter gauge adjustable from 0–180° • Front support arms in custom lengths • Special throat depth of 500 mm • Full-length openable front finger guard cover • Front finger safety light curtain • Special blades • Laser cutting line indicator • Oil heater or oil cooler • Automatic or manual central lubrication • Electrical cabinet with air conditioning • CNC front sheet support arms • CE-compliant rear light barrier • Lightweight guard TECHNICAL SPECIFICATIONS VALUE Cutting Capacity (450 N/mm²) 10 mm Cutting Capacity (700 N/mm²) 6 mm Cutting Length 3100 mm Cutting Angle 0.5 – 3° Cutting Speed / Fast Mode 7 / 13 strokes per minute (spm) Throat Depth 250 mm Backgauge Travel (X) 1000 mm Table Length 3600 mm Table Width 880 mm Motor Power 22 kW Weight 10.5 tons

Condition: good (used), functionality: fully functional, Year of construction: 2008, working width: 3,080 mm, sheet thickness (max.): 13 mm, Equipment: emergency stop, finger protection, foot remote control, For sale: Durma VS 3013 hydraulic guillotine shear, lightly used, single owner, manufactured/purchased in 2008 (supplied by Vendo Kft.). The machine is in very good technical condition and has been regularly maintained. Key Specifications: Cutting length: 3080 mm Maximum sheet thickness: 13 mm (steel), approx. 10 mm (stainless steel) Kljdpfxjx Tarae Adwol Drive system: Hydraulic Back gauge: Motorized Hold-down system: Hydraulic clamps Frame: Heavy-duty welded steel construction Machine weight: 12,900 kg Condition: Very good Location: Tatabánya, Hungary Price: EUR 21,500 net The machine can be inspected and tested at our facility in Tatabánya, Hungary.

Condition: used, Year of construction: 2008, sheet width 1530 mm plate thickness 4.0 mm thickness at "Niro-steel" 2.0 mm no. of strokes max. 34 Hub/min cutting angle 2.70 Grad distance between columns 1540 mm work height max. 920 mm Control konv. voltage 400 V engine output 3.2 kW weight of the machine ca. 1115 kg. range L-W-H 2275 x 2220 x 1400 mm Features: - Robust motorized swing-arm guillotine shear - Break-resistant, torsion-resistant welded steel construction - Compact and easy-to-use machine design - Manual backgauge, adjustable from the rear * Stepless adjustment across the entire travel range - 1x hold-down bar - 1x freely movable foot switch - Front, extendable table extension - Rear safety device - Original operating instructions * Optional accessories included: Klodpjxyln Rsfx Adwel - Sheet metal holding device for thin sheet metal blanks

Condition: ready for operation (used), Year of construction: 1997, sheet width 3230 mm plate thickness 2.5 mm thickness at "Niro-steel" 1.5 mm no. of strokes 28 - 42 Hub/min cutting angle 1.60 Grad table height 820 mm distance between columns 3540 mm Control ELGO 87P engine output 6.8 kW weight of the machine ca. 3410 kg. range L-W-H 4070 x 2070 x 1400 mm from a maintenance workshop Kodpfx Adsxacd Nowjll including special accessories (!!) Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - NC electro-motorized back stop - including NC ELGO "TYP 87P" digital control unit * adjustable from the front right * with target/actual value position input * continuous adjustment over the entire travel range * rough adjustment via push buttons * protection of the limit values ??with limit switch - "Duo-Cut" drive with two dynamic, powerful gear motors - support table with recessed grips - hold-down bar with hard rubber strip - all-steel knife with two cutting edges - selector switch for single and continuous stroke - 1x freely movable foot switch - safety device at the rear - original operating instructions Special accessories included: - pneumatic sheet holding device for thin sheet metal cuts - 1x extra long side stop, including support foot + digital stop - 2x extra long, front support arms * with "SLIDING" mount - for easy moving

Condition: used, sheet width 3100 mm plate thickness 2.00 mm thickness at "Niro-steel" 1.25 mm no. of strokes max. 36 Hub/min cutting angle 0.9 Grad table height 800 mm table width 430 mm distance between columns 3200 mm back stop - adjustable 5.0 - 750 mm Control konv. engine output 3.0 kW weight of the machine ca. 1950 kg range L-W-H 3730 x 2070 x 1400 mm Original price approx. 45.000 euros (!!) Special price on request Features: - Robust / motorized swing-cut guillotine shears - Machine with manual material/backgauge * Travel range 5.0 – 750 mm stop depth * Analog position display * Manual adjustment from the front Klsdexcyw Ejpfx Adwel - Break-proof, torsion-free steel welded construction - Compact and clear machine design - 1x hold-down beam * Hold-down opens before the knife beam moves up * No kinking of very sensitive sheets - Manual cutting gap adjustment - Integrated sheet metal holding system for thin sheet metal cuts - Sheet metal/cut material removal at the front (operator side) - 1x side stop with mm scale - 3x table extensions - 1x freely movable foot switch - Operating instructions (PDF

Condition: used, sheet width 2540 mm plate thickness 2.00 mm thickness at "Niro-steel" 1.25 mm no. of strokes max. 63 Hub/min cutting angle 1.13 Grad table height 750 mm table width 320 mm distance between columns 2620 mm back stop - adjustable 5.0 - 550 mm Control konv. engine output 3.0 kW weight of the machine ca. 1600 kg range L-W-H 3100 x 1980 x 1400 mm Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - manual back stop, with analogue display * adjustable from the front * stepless adjustment over the entire travel range - recessed grips in the support table - 1x hold-down bar - 1x side stop - 3x support arms - 1x freely movable foot switch - operating instructions (PDF) Special accessories included: - sheet metal holding device for thin sheet metal cuts Kledpfxjxacfto Adwjl

Condition: new, sheet width 1050 mm plate thickness 2,0 mm distance between columns 1050 mm down holder 1 Stück fence Tisch 80 - 480 mm fence Breiten 0 - 600 mm table-size 1300 x 600 mm Klodpfxsxabdhs Adwsl work height max. 760 mm total power requirement manuell kW weight of the machine ca. 413 kg. range L-W-H 2,0 x 1,04 x 1,6 m - Including adjustable stop on the work table for miter cuts - The knife can be lifted easily thanks to the counterweight on the back - Large work table for safe placement of the sheet metal plates - Sheets can be pushed through, i.e. longer sheets can be cut - Handwheel on the front to adjust the back gauge - Comes with a robust cast iron base as standard - Long service life thanks to knives made of quality steel - Standard with hold-down device including quick-release clamp - Robust machine construction for high stability Furnishing: - manual lever shears - stable execution - hold-down bars - Side scale with unit of measurement - Table stop / width stop

Condition: used, sheet width 2040 mm plate thickness 3.0 mm thickness at "Niro-steel" 1.5 mm no. of strokes 50 Hub/min cutting angle 1.4 Grad table height 750 mm distance between columns 2120 mm back stop - adjustable 1.0 - 550 mm column arm 100 mm Control manuell engine output 5.5 kW weight of the machine ca. 2050 kg. range L-W-H 2600 x 1980 x 1400 mm Furnishing: - robust / motorized swing-cut guillotine shears - Shatterproof, torsion-free steel welded construction - compact and clear mechanical design - manual backgauge, with analogue position display * adjustable from the front * Continuous adjustment over the entire travel range * Adjustment range 1.0 - 550 mm - Machine side stand with projection .. 100 mm - manual cutting gap adjustment - 1x hold-down bar - 1x long side stop - 2x support arms - 1x freely movable foot switch - rear sheet metal slide - 2x EMERGENCY stop buttons at the front - Connection cable including plug - original instruction manual * Machine link: Kledpexaaqasfx Adwol ?machineno=1008-9325338

Condition: used, sheet width 4080 mm plate thickness 2.0 mm ST thickness at "Niro-steel" 0.8 mm Sheet thickness for ALU 2.5 mm cutting angle 1.3 Grad no. of strokes 34 Hub/min distance between columns 4310 mm back stop - adjustable 15.0 - 750 mm table height 820 mm Control ELGO engine output 9.0 kW weight of the machine ca. 3600 kg. range L-W-H 5250 x 2200 x 1400 mm Good condition (!!) Current new price approx. €70,000 Special price upon request The MHSU motor-driven guillotine shear is based on a torsion-free, rigid welded construction and a dynamic, quiet, and powerful gear motor. High static and Klodpfx Aexabc Rodwol dynamic rigidity is ensured by robustly dimensioned main components such as the cutter bar, support table, side supports,and the main drive unit. The motor- driven guillotine shear was developed forsheet metal and plastics processing. With these shears, you can effortlessly produce clean cuts in series. Features: - NC robust, motorized swing cut guillotine shears - with ELGO NC control unit * Digital position display of the backgauge * Adjustable from the front right * With target/actual value input * Continuous adjustment across the entire travel range * Limit switch protection - NC motorized material/backgauge - Shatter-proof, torsion-free welded steel construction - Compact and clearly arranged machine design - Support table with recessed grips - 1x hold-down bar - 1x side stop with T-slot and scale - 3x front support arms - 1x freely movable foot switch - Operating instructions Optional accessories included: - Pneumatic sheet metal holding device for thin sheet metal blanks

Condition: used, Year of construction: 1963, sheet width 1040 mm plate thickness 2.50 mm thickness at "Niro-steel" 1.25 mm no. of strokes max. 90 Hub/min Klodpfxjxach Io Adwjl cutting angle 2.70 Grad distance between columns 1060 mm work height max. 940 mm back stop - adjustable max. 550 mm column arm 120 mm voltage 400 V engine output 4.0 kW weight of the machine ca. 820 kg. range L-W-H 1650 x 1200 x 1250 mm Equipment: - robust / motorized crank guillotine shears with motor drive - break-proof, torsion-free steel welded construction - compact and clear machine design - manual back stop, with analog position display * adjustable from behind * continuous adjustment over the entire travel range * travel range max. 550 mm - 1x hold-down bar - 1x side stop - 1x front support arm - original operating instructions

Condition: used, Year of construction: 1996, sheet width 2040 mm plate thickness 4.0 mm ST plate thickness 6.0 mm ALU thickness at "Niro-steel" 2.5 mm distance between columns 2100 mm no. of strokes ca. 32 Hub/min cutting angle 2.0 ° table height ca. 820 mm Control SCHRÖDER / ELGO total power requirement 5.5 kW weight 3250 kg range L-W-H 2400 x 1400 x 1100 mm From a maintenance workshop Current new price approx. 35.000 euros Special price upon request The MSS motorized guillotine shear was developed for sheet metal and plastic processing. With these shears, you can effortlessly produce clean cuts in series. The MSS "oscillating cut" is the elegant and powerful way to cut. Thanks to the oscillating cut technology, the applied force is optimally converted into a cutting movement, giving the machine power reserves. Features: - Robust, motorized swing-cut guillotine shears - Shatter-proof, torsion-free welded steel construction - Compact and clearly arranged machine design - NC electro-motorized backgauge * with SCHRÖDER / ELGO NC control unit - Manual cutting gap adjustment * Centralized - adjustable with a simple handle - 1x hold-down bar - 1x sturdy 1.000 mm side stop - including T-slot and mm scale - 2x front support arms 1.000 mm - Grip recesses in the support table - 1x freely movable foot switch - Rear sheet chute - Operating instructions Kjdpfjxaa Edjx Adwoll

Condition: used, sheet width 1050 mm plate thickness 3.0 mm thickness at "Niro-steel" 1.5 mm no. of strokes 35 Hub/min cutting angle 2°30 ° Kledpfsxablljx Adwol engine output 3.0 kW table height 810 mm weight of the machine ca. 1150 kg. range L-W-H 1300 x 1520 x 1170 mm from a maintenance workshop (!!) Furnishing: - robust electro-motorized metal sheet shears - manual backgauge - adjustable up to 610 mm, using the handwheel from the back - 1x side stop including mm scale - 2x table sheet metal support arms - Piece counter - freely movable foot switch - rear sheet metal slide - EMERGENCY stop button at the front * Machine link: ?machineno=1008-9325126

Condition: used, Year of construction: 1998, sheet thickness: 8driving power: 18,5weight approx.: 5800messurements (LxWxH): 2130 x 3260 x 2360sheet length: 1550 Max. cutting length: 1550 mm side. Projection in column: 50 mm Sheet metal passage: 16 mm Cutting angle adjustable: 2°30 - 0.5° Empty strokes: 25 - 32 Number of hold-downs: 8 Cutting pressure: 280 bar Oil filling: 300 l Total connected load: 20.1 kW External dimensions: 2130 x 3260 x 2360 mm with - CNC control SIEMENS S 5 for numerical sheet metal bending - Holding up device mot. Scrap switch - Sheet metal removal with conveyor belt - Cutting gap and cutting angle with control programmable - Spare blades - Shear blade for 750 kg strength - Separate hold-down actuation, e.g. cutting after cracking Kedpfevaatlox Adwjll - Hold-down pressure can be set and read from the front - 2 rocker stops - Finger protection with recessed grip - Balls in the support table - Angle stop with Norius -Foot switch used in good condition Price on request. Delivery: from warehouse or location free loading truck. Payment: in the case of takeover purely net or by agreement. Technical specifications are non-binding. Errors excepted.

Condition: used, Year of construction: 2000, sheet length: 4.100sheet thickness: 12total power requirements: 30weight approx.: 16300messurements (LxWxH): 5350 x 2250 x 2250back gauge: 1000New Price: approx. 100,000 EURO Condition: Used, very good condition Equipment: - Swing cut execution - NC preset control ELGO for rear gauge - Motorized rear gauge up to 1,000 mm on ball screw spindles, foldable - Clearly arranged control panel mounted on a swivel arm - Hydraulic hold-downs positioned close to the cutting edge - Footswitch - Central manual cutting gap adjustment Accessories: - 1 side fence 1,500 mm with scale, T-slot, and tilting bolt Kodpfxewiatve Adwell - 2 sheet metal support arms 1,000 mm with T-slot - Easy replacement and resharpening of the blades - Adjustable cutting length for efficient processing - Lower blade 4-fold reversible - Upper blade 2-fold reversible Additional Details: - Operating manual in GERMAN - Machine and equipment comply with CE regulations

Condition: used, LVD Shear Type HST C-10/31 Kledsx Tqtbepfx Adwol Capacity 3000 x 10

Condition: ready for operation (used), Heavy hydraulic press Klodpfx Adeu R U Szowsl

Condition: excellent (used), Technical data: Maximum cutting width: 3100 mm Maximum cutting capacity for steel St40: 16.0 mm Motorized adjustable backgauge: 1050 mm Motorized adjustment of cutting gap Motorized cutting angle adjustment: 0.5 – 4° Working height: 860 mm Motor power: 18.5 kW Side safety guard with rear light curtain Dimensions (L x W x H): approx. 4650 x 2200 x 2050 mm Kjdpfoyapbiex Adwell Weight: approx. 13 tons Condition: Very good condition Blades 80%, cuts sheets 1 – 16 mm The seller assumes no liability for typographical or data transmission errors. The machine is in appearance, technology, and wear consistent with its age; used machines are sold without any guarantee.