Used Hydraulic Plate Bending Machine for sale (79,210)

Condition: excellent (used), Technical Details: Working width: 3100 mm Maximum bending capacity: 16.0 mm Gbsdoxyvx Tspfx Ap Deu Maximum pre-bending: 12.0 mm Top roll diameter: 300 mm Side roll diameter: 270 mm All three rolls powered Hardened rolls Conical bending device by tilting of both side rolls Swiveling control panel with digital display Hydraulic drop end bearing Motor power: 7.5 kW Dimensions (L x W x H): approx. 5800 x 1700 x 1500 mm Net weight: approx. 8.5 tons The seller is not liable for typing or data transmission errors. The machine's appearance, technical condition, and wear correspond to its age; used machines are sold without any warranty.

Condition: excellent (used), Technical specifications: Retrofit in 2026 Working length: 2550 mm Max. bending capacity: 6.0 mm Bending allowance: 4.0 mm Gedpfszbcwmex Ap Dsbu Diameter of upper roller: 200 mm Diameter of lower roller: 180 mm Hydraulic folding bearing Taper bending device Control panel with digital display Motor power: 5.5 kW Dimensions (length x width x height): approx. 3600 x 1150 x 1250 mm Weight: approx. 4.5 tons Condition: Very good, retrofit in 2026 The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear correspond to its age; used machines are sold without any warranty.

Condition: good (used), Technical specifications: Working width: 4050 mm Gsdpfowkaaljx Ap Djbu Max. bending capacity: 6.0 mm Max. pre-bending: 4.0 mm Top roller diameter: 210 mm Side lower roller diameter: 210 mm Middle lower roller diameter: 210 mm Conical bending device by tilting the two side rollers Hydraulic folding bearings Pivoting control panel with digital display Dimensions (length x width x height): approx. 6900 x 2300 x 1800 mm Weight: approx. 14 tons The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: like new (used), Year of construction: 2001, Technical data: Working width: 2050 mm Max. bending capacity for normal steel St40: 4.0 mm Max. edge bending for normal steel St40: 2.0 mm CNC control: MG Diameter of top roller: 140 mm Diameter of side bottom rollers: 105 mm Diameter of central bottom roller: 130 mm Conical bending device Working height: 800 mm Mobile control panel Hydraulic folding bearings CE marking Motor power: 3 kW Dimensions (length x width x height): approx. 3400 x 1200 x 1200 mm Gjdpfsza D U Dsx Ap Dobu Weight: approx. 2.5 tons Condition: Very good condition, very little use The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear correspond to its age; used machines are sold without any warranty.

Condition: like new (used), Year of construction: 2020, Technical data: Working width: 2050 mm Gbodpfxoyzc Iae Ap Dju Max. bending capacity (mild steel St40): 6.0 mm Max. pre-bending (mild steel St40): 4.0 mm Top roll diameter: 170 mm Side lower roll diameter: 170 mm Central lower roll diameter: 145 mm Cone bending device Hardened rolls Working height: 800 mm Mobile control panel Hydraulic drop-end bearing CE marking Motor power: 2.5 kW Dimensions (L x W x H): approx. 3600 x 1200 x 1200 mm Net weight: approx. 3 tonnes Condition: Very good, almost as-new condition, very little used The seller is not liable for typographical or data transmission errors. The machine's appearance, technology and wear are age-appropriate; used machines are sold without any warranty.

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, roller diameter: 60 mm, working width: 1,050 mm, sheet thickness (max.): 1 mm, roll metal bending machine Isitan 1050 X 1.2mm Manual 3 roll Bending Machine, excellent condition for sale manufacturer: Isitan 1050X1.2 Gjdpfx Ajwk Rlxep Dsbu max sheet width: 1050mm max sheet thickness: 1.2 mm Wire grooves at the ends of the rollers Conical bender roller diameter: 60mm Upper roller removable for easy workpiece removal machine dimensions: length: 130cm height: 100cm width: 65cm weight: 240kg

Condition: excellent (used), Year of construction: 2007, Technical data: Working length: 2550 mm Max. bending capacity for small diameters: 12.0 mm Bending capacity from diameter 900 mm: 18 mm Bending allowance: 10 / 12.0 mm Roller diameter: 310 mm Hydraulic folding bearing Drive power: 11 kW Lateral bending support Gsdpoztckijfx Ap Debu Sheet metal holding device Digital display Dimensions (length x width x height): approx. 4200 x 1500 x 1650 mm Weight: approx. 10 tons Condition: Overall in very good condition, used only sparingly. The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: excellent (used), Year of construction: 2012, Technical Data: Working width: 2600 mm Gbodpfx Apjx Ii Hvj Dsu Bending capacity: 20.0 mm Pre-bending: 16.0 mm Top roll diameter: 330 mm Middle roll diameter: 300 mm Side rolls diameter: 240 mm Conical bending device via tilting of both side rolls Mobile control panel with digital display Motor power: 11 kW CE mark Dimensions (L x W x H): approx. 5800 x 2300 x 1900 mm Weight: approx. 11 t Additional equipment: Upper bending aid The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: good (used), Year of construction: 2000, machine/vehicle number: 21977-1964, Offer 26165 Technical Data - Two driven rollers, each hydraulically adjustable - For edging and conical rolling - Operation via a separate control panel, with digital actual value display Gjdpfx Aezf Hkdjp Djbu - and manual operation - Max. working width 1300 mm - Max. sheet thickness at 400 N/mm² without edging - at bending diameter 370 mm, inside 30 mm - with edging at bending diameter 370 mm, inside 25 mm - without edging at bending diameter 380 mm, inside and - width of 370 mm 45 mm - Upper roller diameter each 300 mm - Side roller diameter each 310 mm - Working speed 4.5 m/min - Drive 400 V / 30 kW - Space requirement W 5800 x H 1900 x D 2200 mm - Weight 8500 kg

Condition: excellent (used), Year of construction: 2006, Technical specifications: Working width: 2100 mm Bending capacity: 28.0 mm Springback: 22.0 mm CNC control Diameter of upper roller: 350 mm Diameter of middle roller: 330 mm Diameter of side rollers: 240 mm Godex Dtt Aepfx Ap Dobu Hardened rollers Conical bending unit by inclining the two side rollers Mobile control panel with digital display Motor power: 7.5 kW CE marking Dimensions (length x width x height): approx. 3600 x 1500 x 1500 mm Weight: approx. 14.5 tons The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear and tear are consistent with its age; used machines are sold without any warranty.

Condition: excellent (used), Year of construction: 1998, Technical data: Working width: 2000 mm Bending capacity: 25.0 mm Pre-bending: 20.0 mm CNC control Top roller diameter: 320 mm Middle roller diameter: 320 mm Side roller diameter: 240 mm Hardened rollers Conical bending device by tilting the two side rollers Mobile control panel with digital display Engine power: 11 kW CE mark Dimensions (length x width x height): approx. 4500 x 2000 x 1900 mm Weight: approx. 11 tons The seller is not liable for typing or data transmission errors. The machine's appearance, technology and wear are in keeping with its age; used machines are sold without any warranty. Gbjdpfxov Htnij Ap Dsu

Year of construction: 2024, condition: new, We are offering this new Machine Wala Enterprise MSA-2 double-die semi-automatic paper plate making machine, manufactured in 2024. Manufacturer: Machine Wala Enterprise Model: MSA-2 Year of Manufacture: 2024 Condition: New Gbodpfxsz E Dame Ap Dou Category ID: 691 Type: Double-die semi-automatic paper plate making machine If you have any questions or require further information, please send us a message or call us.

Condition: excellent (used), functionality: fully functional, Year of construction: 2024, actuation type: electric, roller diameter: 90 mm, working width: 1,270 mm, sheet thickness (max.): 3 mm, overall weight: 520 kg, power: 1.1 kW (1.50 HP), input voltage: 400 V, rotational speed (max.): 6 rpm, type of input current: three-phase, Equipment: cone bending device, emergency stop, foot remote control, hardened rollers, swiveling upper roller, sheet metal roll bending machine BOLUK BM 1270 x 90 - 2.5 mm NEW! for sale. manufacturer: BOLUK 1270X90mm year of manufacture: 2024 Gbjdpfx Aexhub Asp Deu Bending Length: 1270 mm Bending capacity: 2.5 mm Roller diameter 90 mm - SAE 1050 certified high tensile steel rollers - Wire grooves at the ends of the rollers (4/6/9) mm - Manually adjustable rear roller - Mobile control panel with foot pedal - Precision bending with brake motor - Conical bending device - Manually foldable end - Cast iron main frames Bending speed 6m / min Motor power 1.1 kW 50Hz 380v Wire groove diameter 4/7/10 mm Machine dimensions 1850x700x1200 mm Weight 520 kg

Condition: good (used), You are bidding on: a branded machine set – a folding machine from a renowned and well-known manufacturer – Schechtl HA and a guillotine shear RAS by Reinhard Maschinenbau Sindelfingen. Machine details: Folding machine: - Die rail bends cleanly – test possible on site - Angle display - Bending length slightly over 2.5m Gbedpfx Apjyqytqo Dsu - Sheet metal capacity: 1.5 mm for steel – also suitable for aluminium, zinc, etc. - Standard die rail - Foot-operated closure - Current new price approx. €20,000 net Guillotine shear RAS: - Electrically operated guillotine shear up to 2mm steel – also suitable for aluminium, etc. - Cutting length: 2.5m - Extension table for special applications included in the price – can be mounted on the left side - Optional spare blades available - Adjustable depth gauge from the front - Many additional onsite tools and auxiliaries available as options - Machines can also be purchased individually Important: Optionally, you will also find a wide range of machines and equipment for sheet metal and steel processing on offer in our shop, including various rails, depth gauges – everything relating to bending and shearing, such as press brakes, guillotine shears, drilling machines, slip rolls, slitting and profiling machines, accessories (beading devices, round rollers for gutter fabrication, back gauges, etc.), as well as hand tools and spare parts from many top manufacturers in stock. Please feel free to contact me for any questions. You will receive an invoice in accordance with § 25a UstG, VAT is included in the invoice amount (margin taxation system). Free loading available – approx. weight: bending machine about 1900 kg, shear about 1600 kg. Inspection and testing are possible and encouraged by prior phone appointment. Payment in cash upon collection. Benefit from our experience and expertise – we are happy to advise you. Collection by the buyer (or a shipping company commissioned by the buyer) should take place within 10 days after the end of the auction. Location: 97249 Eisingen, approx. 3 minutes from the A3 and A81 motorways. Article number: Folding machine RAS 251009

Condition: new, Year of construction: 2026, sheet width 3100 mm plate thickness 9 mm pre-bending 6 mm diameter of upper rolls 220 mm diameter of lower rolls 200 mm side roll diameter 170 mm min. dia. 250 mm roll speed 6 m/min total power requirement 10,3 kW weight of the machine ca. 4651 kg dimensions of the machine ca. 4915 x 1120 x 1235 mm Features - Machines include the following DAVI standard specification: The components of the machine structure (machine stand, frame and swivel bearings, etc.) have been calculated and designed to withstand the loads required for the applications and performance levels. The robust and heavy-duty machine construction absorbs the loads generated during the bending process without transferring them to the foundation. - High-quality surface finish: For forming delicate surfaces and/or soft materials without leaving marks Hydraulic-mechanical parallelism system, supported by electronics for fine-tuning. There are two INDEPENDENT & SYMMETRICAL hydraulic circuits for the left and right cylinders of each roller. The oil flow is regulated by two DOUBLE PUMPS, which are mounted on the same motor shaft and are fully synchronised. The two symmetrical hydraulic circuits move the cylinders and supply Godpfx Asz Dxpmjp Djbu the rollers with the SAME amount of oil in a fully synchronised manner. Electronic control is activated only for extremely precise fine-tuning. - Smooth transmission of the drive Both the hydraulic motors and the gearboxes (top and bottom) can follow the deflection of the roll without load when bending narrow sheets. This ensures perfectly symmetrical deflection of the rolls under load. This system also allows the rollers to deflect freely, without the risk of breakage under excessive load. - ‘Roll-by-Wire’© digital technology Since 2004, DAVI has revolutionised the way sheet metal rollers are wired (similar to ‘fly-by-wire’ technology in the aerospace, FMS and automotive industries) and introduced ‘Roll-by-Wire’ technology. This allows the entire control system of the roller to be controlled via digital signals rather than, as was previously the case, via numerous relays and contacts. Digital technology is much faster and more reliable. Action Benefit Reduction in the number -> Reduction in potential of components component failures Very compact design -> Improved accessibility for maintenance work Improved accessibility for -> Damaged parts can be identified maintenance work more easily More reliable -> Greater accuracy thanks to the use of ‘digital signals’ Permanent lubrication technology The lever-arm feed system eliminates all linear friction during the movement of the side rollers, as the roller support arms, which house the bushings, rotate simply and smoothly around two large, strong pivot points made of alloy steel, ensuring precise and friction-free rotation. This guarantees reduced wear and safety during unlimited use. Further advantages of the lubrication-free lever-arm feed mechanism are: •NO daily maintenance required (lower operating costs). •More production time available. •The bearings are sealed to protect against scale, dust and rust - Hardened rollers •Excellent heat tre...

Condition: used, functionality: fully functional, Year of construction: 2004, machine/vehicle number: 220692, Equipment: emergency stop, sheet width 1550 mm Gbjdszxt Txspfx Ap Dou plate thickness 6 mm diameter of upper rolls 228 mm drive elektronisch zwei angetri

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, For sale and available immediately: Used PICOT rolling machine Year: 2019 Type: RCS235-30 3 motorized rollers Maximum length: 3100 mm Maximum rolling thickness: 8 mm Maximum nibbling thickness: 6 mm Roller diameter: 235 mm Digital roller position display Gbsdpfx Aoz D Suvsp Dju

Condition: used, plate width 1020 mm plate thickness 4 mm diameter of upper rolls 110 mm total power requirement 2,2 kW weight of the machine ca. 900 Kg dimensions of the machine ca. 2,1 x 0,7 x 1,2 m Gedpfxsz N Hwqj Ap Dobu Fasti three-roll plate bending machine / plate rolling machine In excellent condition. The machine was completely overhauled in 2016.

Condition: like new (used), Year of construction: 2021, Hydraulic 4-roll bending machine Digital display of roll positions Gbsdpfx Ajz I D Agsp Dou Capability to form cones Length: 3050 mm Diameter of upper rolls: 220 mm Diameter of side rolls: 180 mm Bending capacity: 7 to 8 mm with a minimum radius of 1000 mm Machine dimensions: 4700 x 1100 x 1330 mm Weight: 5700 kg Operating videos available upon request.

Condition: good (used), Year of construction: 1989, sheet width 2050 mm plate thickness 8.0 mm pre-bending capacity 6.0 mm upper roll diameter 190 mm lower roll diameter 180 mm bending speed 5.2 m/min work height max. ca. 980 mm total power requirement 5.5 kW weight of the machine ca. 3500 kg. range L-W-H 2900 x 1200 x 1280 mm Furnishing: - Robust electro-hydraulic 3-roller bending machine - planetary movement of the bending rollers with reduced center distance - Hydraulic motors combined with planetary gears * for driving the 3 rollers - mobile operating unit, with connection cable + plug - extended roll ends for profile bending rolls - with conical bending device * Inclination of the side rollers by handwheels * Workpiece limitation for a cone with a 45° pitch: * Working length max: 60% * Bending capacity max: 50% - free-moving operation * electric delivery rollers * electric turning/rolling movement * digital position display of the reels Gbodpfxoz Dkzhj Ap Dsu - hardened rollers SAE 1050 CK 45 - Hydraulic folding store for removing closed pipes - safety device (cable) - Original instruction manual + CE declaration * Machine link : ?machineno=1008-9401255

Condition: new, functionality: fully functional, Year of construction: 2026, control type: CNC control, actuation type: hydraulic, controller manufacturer: Siemens, controller model: Smart Line, number of rollers: 4, roller (bottom) diameter: 190 mm, roller (top) diameter: 210 mm, side roll diameter: 180 mm, sheet thickness (max.): 8 mm, sheet thickness steel (max.): 8 mm, power: 11 kW (14.96 HP), input voltage: 400 V, number of digital displays: 1, warranty duration: 12 months, Equipment: documentation/manual, emergency stop, DIGIMA W12-8x3200 Hydraulic Four-Roll CNC Plate Rolling Machine Godpfxeznw T Ue Ap Djbu The DIGIMA W12-8x3200 is a hydraulic four-roll CNC plate rolling machine designed for accurate, repeatable and efficient sheet-metal forming. With a working width of 3200 mm, it is suitable for producing large cylindrical parts, sleeves, pipes, curved sections, housings, tanks and other technical components used in metalworking, steel construction, ventilation, machinery manufacturing and industrial production. The four-roll system provides a major advantage over conventional three-roll machines. The sheet is held securely between the upper and lower rolls, while the two side rolls perform the pre-bending and rolling operations. This arrangement allows both edges of the sheet to be pre-bent without removing and turning the workpiece, reducing handling time and limiting the length of straight sections left at the ends. The result is improved repeatability, higher productivity and more consistent part geometry. The W12-8x3200 can roll sheet metal up to 8 mm thick and perform pre-bending up to 6 mm. Its 3200 mm working length enables the processing of wide sheets for both one-off jobs and series production. The upper roll has a diameter of 210 mm, the lower roll 190 mm, and the side rolls 180 mm. The minimum rolling diameter is 400 mm, allowing the machine to produce a wide range of cylindrical and curved components. The hydraulic drive ensures smooth, stable movement and reliable clamping force throughout the forming process. The 11 kW motor provides the power required for regular industrial operation, while the rolling speed of 4 m/min supports efficient production without compromising process control. The rigid machine body and carefully arranged roll system help guide the material accurately and reduce unwanted deformation. Computerised CNC control makes the machine convenient to set up and operate. The operator can control roll movements, monitor the forming process and reproduce previously established settings for recurring jobs. This is especially useful in batch production, where the same diameter, radius and dimensions must be achieved repeatedly. The control panel also helps reduce setup time and simplifies everyday machine operation. The operating sequence is straightforward. First, the sheet is inserted and stabilised between the rolls. The side rolls then pre-bend the sheet edges, minimising flat ends. Finally, the material is passed through the roll system until the required tube, sleeve, arc or cylindrical shape is obtained. The machine can also be used for forming conical components by applying a controlled inclination of the rolls. Thanks to its wide working capacity and computer-controlled operation, the machine can be used in flexible workshop production as well as organised manufacturing processes. It is suitable for companies producing ventilation ducts, structural elements, machine covers, tanks, steel sleeves and custom-made components. Repeatable CNC settings are particularly valuable when several identical parts must be formed with the same diameter and curvature.

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, A NELA plate bending machine (printing plate bending device) is a professional bending device for offset printing plates, manufactured by the German company NELA Brüder Neumeister GmbH. These systems precisely shape printing plates into the required form, ensuring a perfect fit into the cylinders of offset printing presses. Compatibility: NELA manufactures bending devices specifically tailored to the requirements of major printing press manufacturers. Models like the HD/Nela SM 102 B, which are optimized for Heidelberg Speedmaster (SM 52, SM 74, SM 102) as well as XL machines, are particularly common. A Heidelberg NELA plate punch (also called a printing plate punch, plate perforator, or hole punch) is an essential precision tool in prepress. It is used to punch register holes or cutouts precisely into offset printing plates. This ensures flawless clamping and perfect alignment (register) of the plates in Heidelberg printing presses. Compatibility: Specifically designed for Heidelberg machine series such as the Speedmaster (SM) 52, 74, and 102. Gbodpjz It Skofx Ap Dju Hole spacing: Flexible configurations with variable hole spacings, such as 425 mm and 780 mm (for Autoplate systems), are common.

Condition: excellent (used), functionality: fully functional, Year of construction: 2002, control type: manual, degree of automation: semi-automatic, actuation type: electric, number of rollers: 3, roller diameter: 90 mm, working width: 1,550 mm, roller height adjustment: 110 mm, sheet thickness (max.): 3 mm, sheet thickness steel (max.): 3 mm, overall weight: 600 kg, total length: 2,300 mm, total width: 700 mm, total height: 1,150 mm, power: 1.1 kW (1.50 HP), input voltage: 400 V, input frequency: 50 Hz, Equipment: cone bending device, emergency stop, foot remote control, hardened rollers, swiveling upper roller, AKYAPAK AS 1550x90 sheet metal bending machine 1550mm x 2.5 mm, 3 rollers /ct2289/ Gjdpfexmvgkox Ap Dobu Electric, pedal-operated rolling machine. Strong, robust construction. The upper roller can be rotated to remove the workpiece Convenient to use, suitable for workshops and industry Manufacturer: AKYAPAK AS 1550X90mm Year of manufacture: 2002 Bending Length: 1550 mm Bending capacity: 2.5 mm Roller diameter 90 mm - SAE 1050 certified high tensile steel rollers - Wire grooves at the ends of the rollers (4/6/9) mm - Motorized adjustable rear roller - Mobile control panel with foot pedal - Precision bending with brake motor - Conical bending device - Manual folding end - Cast iron main frames Bending speed 6m / min Motor power 1.1 kW 50Hz 380v Wire groove diameter 4/7/10 mm Machine dimensions 2400x800x1200 mm Weight 600 kg

Condition: new, Year of construction: 2023, neu 2023 9656 prompt, Zwischenverkauf v Gjdpfx Apswira Ue Djbu Türkei 2600 € 1 1 1050 mm 1 mm 56 mm 1400 mm 700 mm 1120 mm 185 kg 3 Walzen asymmetric rolls - prebending longitudinal grooves in lower and lateral roll Infeed of the lower roller by a central lever - with gear reduction machine stand user manual in GERMAN orENGLISH

Condition: used, Hydraulic Profile Bending Machine, Pipe Bending Machine LANG Type Ondomat 60 Serial No. 2589 Year of manufacture: 1970 Bending capacity max.: Ø 60 x 2 mm Pressing force: 20 tons Counterforce: 7.5 tons Gsdpfx Asyi Hrwsp Djbu Maximum bending angle: 135° Tool stroke: 250 mm Maximum tool width: 125 mm External width of tool rocker: 90 mm Motor power: 18 kW Power supply: 380 Volt, 50 Hz - Hydraulic bending process with counterpressure cylinder for wrinkle-free bending - Up to 10 different bending angles in sequence via automatic indexing turret - Two-hand control panel - 1 set of bending dies Ø 30 mm, die width rocker = 78 mm, die width counterholder = 50 mm Required space (L x W x H): 2000 x 750 x 1500 mm Weight: approx. 2 tons Good condition