Used Nozzle Centrifuge for sale (3,541)

Condition: like new (used), Year of construction: 2019, clamping force: 500 kN, Equipment: documentation/manual, _ENGEL – Injection Moulding Machine Technical Data_ Serial number: 232665 Model: E‑VICTORY _Plasticising Unit 1_ • Screw diameter: 18 mm • Listed diameter options: 15 / 18 / 20 mm; 18 mm is installed • Screw stroke: 80 mm • Maximum injection volume: 20 cm³ • Screw speed: 450 rpm • Screw torque: 75 Nm • Plasticising rate, 3-zone screw: 4.2 g/s _Injection Unit 1_ • Version: Standard • Injection rate: 83.97 cm³/s • Specific injection pressure, regenerative mode: 2,400 bar _Nozzle 1_ • Nozzle stroke: 210 mm • Nozzle contact force: 40.6 kN _Material Cylinder 1_ • Screw L/D ratio: 24 • Heating zones, including nozzle: 4 • Heating power: 5.1 kW • Note: maximum available equipment _Clamping Unit_ Lsdpfx Aez Iyldolyjah • Clamping force: 500 kN (approximately 50 tonnes) • Opening stroke + cylinder tolerance: 408 mm • Maximum distance between platens: 600 mm • Minimum mould height: 200 mm • Platen dimensions, horizontal × vertical: 500 × 450 mm • Drop-out chute width: 400 mm • Maximum mould weight on moving platen: 300 kg • Maximum mould weight on stationary platen: 300 kg • Maximum total mould weight: 600 kg • Dry-cycle stroke according to Euromap 6: 150 mm • Dry-cycle time according to Euromap 6: 1.60 s Mould weight notes: 1. Mould overhang according to mounting platens. 2. Less the weight of any rotary table. _Ejector 1_ • Ejector stroke: 100 mm • Ejector force: 39.8 kN _Drive Unit_ • Oil reservoir capacity – injection unit, main tank: 135 l • Oil reservoir capacity – clamping unit, auxiliary tank: 0 l _Machine Basics_ • Total weight without oil: 4.0 tonnes • Total connected power: 65.0 kW Transcription note: the small footnotes below the plasticising section specify reference materials and test conditions. They are not fully legible in this photo.

Condition: excellent (used), Year of construction: 2019, Krauss Maffei KM 121-380 PX / Electric Machine Year of manufacture: 2019 Injection unit: Screw diameter: 35 mm Shot weight: 140 g Injection pressure: 2429 bar Dosing volume: 154 ccm Clamping unit: Clamping force: 120 t Tie bar spacing: 470x420 mm Platen size: 640x590 mm Ejector: electric Clamping unit: toggle Control: MC6 - Touchscreen Additional equipment: Laedpfx Ajz Ipltslyeh Machine in very good technical condition Electric machine: energy-saving and very quiet Operating hours: approx. in automatic mode Euromap 67 Robot interface Air valve with vacuum x 2 Hydraulic core pull x 1 Control system with hot runner nozzles x 15 Injection molding unit is wear-resistant and corrosion-resistant Main motor of the machine - servo motor driven by an inverter - energy saving Central lubrication Parallel movements Automatic tool height adjustment Dimensions: Weight: 9400 kg Length/Width/Height: 5.10x1.60x1.88 m All machines offered are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or to participate in technical live tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2012, Arburg 1200T 1000-290 / Vertical machine with a rotary table Year of manufacture: 05.2012 Injection unit: Screw diameter: 30 mm Shot weight: 97 g Injection pressure: 2500 bar Dosing volume: 106 ccm Clamping unit: Clamping force: 100 t Tie bar spacing: 0x0 mm Platen size: 1200 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - Touchscreen Additional equipment: Vertical machine with a rotary table Euromap 67 Robot interface Air valve x 6 Hydraulic core pull x 2 Control with hot runner system x 18 Injection unit hardened - bimetal Servo motor on the injection unit – fast suction and fast injection Proportional valve on the injection unit – precise injection Self-closing nozzle Primus sensor - tool pressure control Rotary table diameter: 1200 mm Dimensions: Weight: 7200 kg Length/Width/Height: 4.36x1.71x3.66 m All machines offered are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or to participate in technical live tests at our company in Łódź. Lsdpfxez Ipx Te Alyoah Price: On request

Condition: like new (used), Year of construction: 2022, functionality: fully functional, machine/vehicle number: 100372005, travel distance X-axis: 800 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 465 mm, feed length X-axis: 40,000 mm, feed length Y-axis: 40,000 mm, feed length Z-axis: 40,000 mm, feed rate X-axis: 40 m/min, feed rate Y-axis: 40 m/min, feed rate Z-axis: 40 m/min, mount diameter: 63 mm, total length: 5,350 mm, table length: 500 mm, table width: 450 mm, total width: 5,116 mm, spindle speed (max.): 16,000 rpm, total height: 3,082 mm, rapid traverse X-axis: 40 m/min, rapid traverse Y-axis: 40 m/min, rapid traverse Z-axis: 40 m/min, type of input current: three-phase, table load: 250 kg, position of the milling head: Horizontal / Swiveling, workpiece weight (max.): 250 kg, torque: 63 Nm, rotational speed (max.): 16,000 rpm, overall weight: 16,000 kg, working range: 500 mm, tool weight: 6 g, input voltage: 400 V, input frequency: 50 Hz, input current: 90 A, workpiece length (max.): 700 mm, workpiece width (max.): 400 mm, number of slots in tool magazine: 24, Equipment: documentation/manual, rotational speed infinitely variable, Zero hours HAMUEL HSTM 500 HD 5-Axis Turn-Milling Center Was not used in production / just commissioning (by OEM) and preserved. Comes as complete shipset from MFG. - X, Y, Z axis with absolute linear scale - A axis - Swivel axis / B axis - C axis - Pressure control of head clamping - CNC-control system SIEMENS 840D SL - Remote diagnosis system via Ethernet - Patrol light - Control cabinet with air-condition - Milling spindle 16’000 rpm, HSK-A63 - Machining hour counter - Tool handling system with double gripper - Chill unit - Hydraulic unit - Machine housing with front door L shape - Standard machine color scheme - Coolant supply unit, low pressure, paper belt filter - Flush Gun Ljdpfx Aljzvulkeyoah - Chip conveyor - Oil Mist exhaust system - Documentation 1-fold in English + CD Machine option package: High pressure cooling through spindle BEMA automatically adjustable nozzles Tool measuring system BLUM Work piece measuring system BLUM Rotoclear window Handweel HT2 VNCK Siemens simulation Available in Bangkok, Thailand Worldwide shipping

Condition: new, Year of construction: 2016, functionality: fully functional, machine/vehicle number: BOMBA FLOWSERVE 36371.05, overall weight: 2,060 kg, total length: 3,580 mm, total width: 1,900 mm, total height: 2,300 mm, volume flow: 720 m³/h, operating pressure: 14 bar, final pressure: 22 bar, input voltage: 460 V, input frequency: 60 Hz, input current: 440 A, type of input current: three-phase, type of cooling: air, rotational speed (max.): 1,785 rpm, warranty duration: 1 months, protection type (IP code): IP56, New 400 HP Flowserve centrifugal pump; flow rate of 720 m3/h; model 10x6 IMP 564mm. Laodpfxoy Tcczs Alysh

Condition: like new (used), Stainless steel centrifugal sieve machine, rotating sieve. Made entirely of stainless steel. Ljdpewygaksfx Alyjah Motor power: 2.2 kW, 695 rpm. Inlet: 250 x 250 mm. Basket diameter: 280 mm x 940 mm. Outlet: 940 mm x 400 mm. Internal components are removable for cleaning. See also our other listings.

Condition: good (used), Centrifugal pump, acid pump, alkali pump, water pump for groundwater lowering pump -Centrigeminal pump: with stainless steel tank -Motor: 2.2 kW -Flow rate: 1900 l/min Lasdpfx Aleyf Augjyoh -Pumping height: 15 m -Tank capacity: approx. 500 liters -Overall dimensions: 1080/920/H1190 mm -Weight: 126 kg

Condition: excellent (used), GEA Westfalia separator for dewatering industrial and municipal waste water sludge. In excellent condition. Laodpfeyf Hw Sex Alyeh

Condition: good (used), Centrifugal pump, water pump, stainless steel pump, food-grade pump, vertical centrifugal pump, multi-stage vertical centrifugal pump, pressure booster pump, pressure intensifier pump Laodpfxszg Dmxo Alyjh -Manufacturer: Lowara, Multi-stage vertical centrifugal pump -Type: 5SV07F022T -Motor: 2.2 kW / 2860 rpm -Protection class: IP55 -Flow rate: max. 8.5 m³/h -Number: 2x pumps available -Price: per piece -Dimensions: 250/210/H685 mm -Weight: 30.2 kg

Condition: excellent (used), Cutting nozzle, welding torch, MIG/MAG torch, hand arc - piercing torch, gouging torch, gouging nozzle, torch nozzles, cutting nozzles, flame cutting system, torch, oxy-fuel cutting system -Cutting nozzles: Flame cutting nozzles 56 pieces unused Ovp -Type/Quantity: see photos/parts list Laodpew Udkujfx Alysh -Cutting range: 2 - 250 mm -Price/Delivery: complete -Transport dimensions: 200/150/H50 mm -Weight: 0.8 kg

Condition: new, Year of construction: 2018, functionality: fully functional, KSB Etaline ETL 032-032-160 | New In-line Pump no. 6 Manufacturer: KSB SE & Co. KGaA Model: ETL 032-032-160 GGSAV66D200222 (ETALINE) Capacity (Q): 17.00 m³/h Head (H): 18.00 m Rotational speed (n): 2921 rpm Impeller diameter: Ø 132 mm Year of manufacture: 2018 Viscosity (v): 5.5 mm²/s MEI index: ≥ 0.70 Lasdpfey I Dn Iex Alyjh Material number: 01216137 The KSB Etaline is a high-efficiency centrifugal pump with an in-line design (suction and discharge nozzles are aligned on the same axis), allowing for direct installation on the pipeline. This model features a very high energy efficiency index (MEI ≥ 0.70), resulting in low operating costs. The pump is intended for use in heating, air-conditioning, and industrial circulation systems. The robust, red-painted casing and precisely matched 132 mm impeller ensure stable performance parameters at a capacity of 17 m³/h.

Year of construction: 2007, condition: ready for operation (used), functionality: fully functional, Manufacturer: RUMA Type: MZ 150-B700 Serial No.: 2150.354 Year of manufacture: 2007 Volumetric flow rates from 1 to 150 l/min Drive power: 4.0 kW (optional 5.5 kW) Rotor volume: 15.0 liters Laedpfx Aszdf Tcelyjh Solid matter filling volume: 10.0 liters Liquid purification with back pressure (0.7 bar) Possible applications of the centrifuge: In this system, only liquids that do not pose a fire or explosion hazard may be used, and only substances in accordance with the DIN 6601 standard are permitted (DIN 6601: Resistance of materials of containers made of steel to liquids). For example:  Emulsions  Oils  Electrolytes  Grinding fluids  Media with a pH value between 5.5 and 9.5  The solids to be separated must be specifically heavier than the liquid. Operating manual available in German and English.

Condition: new, Year of construction: 2024, NEW Grundfos - The pump is fitted with a 3-phase, fan-cooled, permanent-magnet, synchronous motor. The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status: "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights) "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights) "Alarm": Motor has stopped (flashing red indicator lights). Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". The terminal box has a number of inputs and outputs enabling the motor to be used in advanced applications where many inputs and outputs are required: • two dedicated digital inputs • three analog inputs, 0(4)-20 mA, 0-5 V, 0-10 V, 0.5 – 3.5 V • 5 V voltage supply to potentiometer and sensor • one analog output, 0-10 V, 0(4)-20 mA • two configurable digital inputs or open-collector outputs • two Pt100/Pt1000 inputs Ledpfjyug Hxjx Alysah • LiqTec, dry-running protection sensor input • Grundfos Digital Sensor input and output • 24 V voltage supply for sensors • two signal-relay outputs (potential-free contacts) • GENIbus connection • interface for Grundfos CIM fieldbus module.

Condition: used, Year of construction: 1987, Compressor Make : Ingersol Rand Ledpey Spnuofx Alyjah Type : Centac C60Mx2 Centrifugal Original YOC : 1987 Our supplier bought the mc in 1997, fully reconditioned from Ingersol Rand in Belgium , only used for 2 years in 1 shift, thereafter serviced & stored . User was Picanol demo project in Belgium. See below pictures to see condition & completeness of the unit. Air dryer Hiross MDA65 is included in the package. Intake Pressure : 98 kPa Intake Temperature : 15 °C Relative Humidity : 60% Delivered Capacity : 61 m3/min Discharge Pressure : 800 kPa Cooling water temp : 15 °C Cooling water flow : 450 l/min Rated speed : 2970 n/min Motor rating : 430 kW

Condition: used, Year of construction: 1991, Type: WKF 50/12 N.SE Size: DN50 12 stages Lodpfxoy A Rbdo Alysah Standard version with mechanical seal Flow rate: 26.9 l/s (96.8 m³/h) Head: 380 m Speed: 2,960 rpm

Year of construction: 2017, condition: ready for operation (used), Thermo Scientific Heraeus Multifuge X3R TX 750 Refrigerated Centrifuge 2017 No. 611 • Voltage: 230 V, 50/60 Hz Ljdpfx Aljyvtyijyjah • Power consumption: 10.5 A • Power input: 1950 W • Refrigerant: R404A, 0.52 kg (31 bar) • Max. kinetic energy: 62.5 kNm • Max. sample density: 1.2 g/cm³ • Operating temperature: -10 °C to +40 °C • Integrated cooling (refrigerated centrifuge) Dimensions: 670 × 750 × 360 mm (L × W × H) Weight: approx. 140 kg Year of manufacture: 2017 You are welcome to arrange an on-site inspection. We are happy to organize an affordable shipping service for you! You will receive a proper invoice. For international customers, a net invoice can be issued, provided a valid VAT ID number is given. Subject to prior sale. Visit our shop and check out our other offers as well. All brand names and trademarks mentioned are the property of their respective owners and are used for identification and description purposes only. Technical data variations and errors in the description may occur and are subject to change.

Condition: like new (used), Year of construction: 2020, functionality: fully functional, tank capacity: 15,000 l, usable tank capacity: 15,000 l, total height: 3,875 mm, outer diameter: 1,750 mm, overall weight: 2,900 kg, wall material: stainless steel, wall thickness: 8 mm, manhole diameter: 610 mm, manhole location: top, operating temperature: 80 °C, Equipment: sanitary facilities, Brand new, never commissioned. Professionally decommissioned from an INEOS manufacturing facility prior to first use. Manufactured by Able Engineering, this high-specification sanitary 316L stainless steel pressure vessel is suitable for pharmaceutical, cosmetics, personal care, food, beverage and fine chemical applications. Designed for vacuum and low-pressure service and suitable for installation within ATEX-rated environments. Constructed entirely in 316L stainless steel throughout with 8mm shell and dish walls, dished top and bottom heads, heavy duty tubular stainless steel leg supports with bolt-down base plates, hygienic internal finish < 0.8 Ra, and full hygienic ferrule fittings throughout conforming to ASME BPE / BS3062. Suitable for CIP, excellent condition. Material: 316L Stainless Steel throughout. Working Volume: 15,000 Litres. Shell ID: 2,930mm. Overall Height: 3,875mm. Shell & Dish Wall Thickness: 8mm. Design Pressure: -1.0 to +0.45 Bar.G. Design Temperature: -10°C to +100°C. Empty Weight: 2,900kg. Design Code: PD5500:2018, Cat.3. PED 2014/68/EU certified. Manufacturer: Able Engineering. Serial Number: PXL19635-3. Factory Tested: September 2020. Nozzles and fittings include 610mm hinged manway, CIP inlets with dip pipe and TOD clip-on spray fittings, pressure relief valve connection, nitrogen blanketing connection with pressure indicator, Endress & Hauser hygienic thermowell, flush polished level switch, level measurement connection, lifting lugs, and earthing boss. Two units currently available, both brand new and never commissioned, sourced directly from the same INEOS facility. Tank saddles available on request for either single use or purchase. Please view our other listings for additional sizes and configurations — all stock is brand new, ex-INEOS, and available for immediate inspection and purchase. Original engineering drawings and full nameplate documentation available on request. Inspection welcome by appointment. Loading and transport can be arranged. Laedpezhn Ngjfx Alysh Tracht Ltd specialise in hygienic process equipment for the food, beverage, cosmetics, pharmaceutical and chemical industries, with practical experience supporting both batch and continuous manufacturing environments. In addition to process vessels, Tracht Ltd supply and install stainless steel mixing vessels, Silverson high-shear mixers, hygienic lobe pumps, hygienic centrifugal pumps, access gantries, and provide full vessel installation and commissioning services. Whether replacing existing equipment or expanding production capacity, Tracht Ltd can specify, supply and install the right equipment for your application. . Please contact us for further information or to discuss delivery and installation options.

Condition: excellent (used), CATALOGUE NUMBER 7134 TECHNICAL DATA - max planing width 500mm - max planing height 190mm Top: - feed rollers - infeed roller, sequential Laodpfozxhdfox Alyoh - pressure rollers, 2 rows - infeed roller, sequential - planing roller 500mm, 4-knife, 7.5kW motor - pressure rollers - outfeed roller, smooth - pressure roller on the outfeed Bottom: - adjustable infeed table + pressure roller - smooth feed roller - planing roller 500mm, 4-knife, 5.5kW motor - 2 smooth feed rollers - side pressure roller Rear: - side spindles 1) vertical right 140mm 4kW 2) vertical left 140mm 4kW - spindle diameter 40mm - spindles adjustable up/down, right/left - stepless feed speed adjustment 8-30m/min - electric table lifting - dust extraction nozzle diameters 2x145mm, 2x160mm - dimensions L/W/H 2050x1700x1700mm - weight 2100kg ADVANTAGES – ideal for processing flooring panels – electric table lifting – Czech production – used planer, very good condition Net price: 37900 PLN Net price: 8814 EUR, depending on the exchange rate of 4.30 EUR (Prices may change due to higher fluctuations)

Condition: excellent (used), Year of construction: 2009, Arburg 370 S 600-290 (2009) Screw ø 35 mm 📐 CLAMPING UNIT Clamping force: 600 kN Closing force: 38 kN Opening force / increased: 24 / 160 kN Laodpfszrvy Uox Alyjh Opening stroke: 400 mm Mould height min.: 200 mm Daylight max.: 600 mm Distance between tie bars: 370 × 370 mm Platen size: 510 × 510 mm Weight of mov. mould half: 360 kg Ejector force: 125 kN Ejector stroke: 125 mm ⚙️ HYDRAULICS Drive power: 15 kW Total connected load: 23,9 kW 💉 INJECTION UNIT — ø 35 mm Screw stroke max.: 150 mm Effective screw length L/D: 20 Injection volume max.: 132 cm³ Shot weight max.: 20,5 g PS Material throughput max.: 10,5 kg/h PS Injection pressure max.: 2000 bar Injection flow max.: 140 cm³/s Injection flow with accumulator: 430 cm³/s Back pressure max.: 350 / 200 bar Screw speed max.: 54 m/min Screw torque max.: 380 Nm Nozzle contact force: 60 kN Nozzle retraction stroke: 240 mm Heating zones / power: 4 zóny / 5,8 kW Nozzle heating: 0,6 kW Hopper capacity: 50 l 📦 DIMENSIONS & WEIGHT Oil capacity: 135 l Net weight: 3300 kg Electrical connection: 80 A

Condition: excellent (used), Catalog number: 8059 TECHNICAL DATA - max width of the workpiece 200mm - max height of the workpiece 140mm - number of spindles 4 1) horizontal lower 200mm, 5.5kW 2) vertical right 140mm, 4kW 3) vertical left 140mm, 4kW 4) horizontal upper 200mm, 5.5kW - all heads adjustable up/down, left/right - spindle diameter 40mm - spindle speed 6000 rpm – top: - 6 infeed rollers, toothed, including 2 double rollers - outfeed roller, toothed, double, rubber – bottom: - side pressure roller - infeed roller, toothed, helical, in the lower table - side pressure roller - outfeed roller, smooth, metal - all rollers pneumatically pressed - length of the infeed table 1600mm - table adjustable up/down - central lubrication - electric setting of the planing thickness - lifting motor 1.1kW - stepless feed rate adjustment - feed motor 3kW - feed on Cardan shafts - enclosed in a cabinet - diameter of the dust extraction nozzle 4x140mm - dimensions L/W/H 3200x1700x1750mm - weight 3000kg ADVANTAGES Ledpfezx Sn Uox Alyoah – for 4 heads – ideal for both wet and dry wood – used machine, very good condition Net price: 51900 PLN Net price: 12070 EUR, depending on the exchange rate of 4.30 EUR (Prices may vary due to higher fluctuations)

Condition: used, Year of construction: 2016, Waste disposal system consisting of: 1 Clean air dust collector with briquetting press JP 350-L 1 Clean air dust collector with rotary valve airlock JZ 350-L Year of manufacture: 2016 Technical data JP 350-L: Suction nozzle: 350 mm Nominal volume flow: 6580 m³/h Maximum volume flow: 8000 m³/h Negative pressure at nominal volume flow: 2750 Pa Motor power: 11 kW Rated speed: 3000 rpm Technical data briquetting press CS3-12: Throughput capacity max. 50 kg/h or 0.75 m³/h (material-dependent) Motor, hydraulic pump: 3.0 kW Motor, agitator: 0.37 kW Ljdpfx Aoz Rrbdolyeah Motor, dosing screw: 0.75 kW External fuse: 16A Briquet diameter: 65 mm Weight: 780 kg Storage container: 1200 x 1200 mm Overall external dimensions: 3150 x 1625 x 2742 mm Space required: 4500 x 3000 x 2900 mm Availability: approximately 11/2027 Location: Hesse

Condition: like new (used), For sale is a fully functional pallet box washer, used but recently overhauled by the manufacturer. The following components have been newly replaced: chemical dispenser, heating elements, rotary nozzle, complete control system with frequency inverter, and minor parts. The washer features a cycle that first applies foam and then washes the boxes, with two types of nozzles for foaming and washing. Loading and unloading of boxes is carried out by the pneumatic opening of the front door to a position level with the ground. When the door is open, boxes can be loaded either by forklift or manually. A video demonstrating the machine's operation is available. The set also includes two safety barriers for operating the door. Lasdpfxsyxv Hwj Alyeh

Condition: excellent (used), CATALOG NUMBER 7918 TECHNICAL DATA - Max. saw blade diameter: 450mm - Spindle diameter: 30mm - Pneumatic top clamp - Blade guard - Blade guard also functions as a hold-down clamp - Pneumatic blade feed - Cutting height (at 250mm width): 120mm - For lower cutting heights, the cutting width is increased - Main motor power: 6kW - Extraction nozzle diameter: 120mm - Table dimensions (LxW): 650x850mm - Table height from base: 1000mm - Roller tables: - Infeed roller table + stop: 3180mm - Outfeed roller table + stop: 2450mm - Roller width: 360mm - Operating pressure: 8 bar - Overall machine dimensions (without roller tables) LxW xH: 1300x1050x1800mm - Weight: 550kg FEATURES – 2 roller tables Lasdjzkgzyopfx Alyeh – Pneumatic blade stroke – Used saw, in perfect condition Net price: 14,900 PLN Net price: 3,550 EUR (based on EUR rate of 4.2) (Prices may change with significant rate fluctuations)

Condition: good (used), Year of construction: 2023, CNC turning machine Manufacturer: DMG Mori Machine model: CLX 350 V3 Control system: SIEMENS Slim Line Multi Touch Year of manufacture: 2023 TECHNICAL DATA Travel distances - C-axis, degrees: 360 Spindle - Spindle head - Bar diameter: (mm): 66 - Max. speed: (rpm): 5,000 - Drive power 100% duty cycle: (kW): 11 - Drive power 40% duty cycle: (kW): 16.5 Turret - Tool positions: 12 - Tool positions for driven tools: 12 - Tool holder: VDI30 Tailstock - Hydraulic, controlled via M-function EQUIPMENT FEATURES + C-axis + Through-hole chuck, diameter 65 mm (max.) + Direct measuring system for the X-axis + Chip conveyor + Electronic handwheel + 3-jaw chuck, diameter 210 mm (hydraulic) + DMG Mori IoT connector + Coolant spray nozzle, 5 bar + Hydraulic tailstock + Tool package - Chip conveyor not included Laedez Sa Svepfx Alyoh Subject to changes and errors in the technical data and specifications.

Condition: excellent (used), Year of construction: 2019, BEAM MODULO 400 Year Mfg 2019 Siemens Control Lodpfx Alszvlhpjysah Build Volume: Approximately 650 × 400 × 400 mm (or roughly 600 × 400 × 400 mm operational) with continuous 5-axis motion kinematics Laser Source: Ytterbium fiber laser options ranging from 500 W up to 2 kW Deposition Heads/Nozzles: Supports an automatic tool changer to swap between different heads (e.g., the 10Vx for fine precision down to 0.1 mm and the 24Vx for higher deposition rates) without stopping production Powder Delivery: Equipped with a vibrating multi-hopper powder feeder system capable of managing up to 4 or 5 separate material feed options