Used Pedestal Drill for sale (5,006)

Condition: used, Column drilling machine ALZMETALL type AB 4 SV Machine no. No. 14805 Year of construction approx. 1980 drilling capacity 40 mm Spindle holder MK 4 - short quill throat 340 mm Quill stroke 180 mm Table size 710 x 560 mm Column diameter 160 mm Spindle speed 30 - 765 rpm infinitely variable Motor power 2.3 and 3.4 kW pole-changing Mains connection 380 Volt, 50 Hz - Spindle speed via 2 motor speeds and infinitely variable via variator gearbox - Reduction gear with 2 gear stages for high torque at low speeds - Spindle on/off via rotary switch or electric foot switch - Automatic feed 0.1 - 0.2 - 0.3 mm/rev - Table height adjustment via hand crank - Machine base with machined workpiece support surface Isdpfx Aen N Ekcedwoal - LED lighting device Space requirement L x W x H 1200 x 725 x 2050 mm Weight 615 kg good condition

Condition: good (used), Nagel Citoborma 180 Paper Drill with Pedestal The machine is in 100% working order. Very good condition. Solid construction – weighs approximately 100 kg. This is one of the newest Citoborma drill models. 380V power supply. One drilling head. Iasdpfox N I Syox Adwol Drill diameter: 2-20 mm. Stack height: 60 mm. The drill table is adjustable in all directions (sides, front/back). It has stops for setting the drilling spacing. In addition, the drill has an automatic table lock that releases after each cycle. The set includes drill bits, tools, a new cutting stick, and instructions.

Condition: ready for operation (used), Spindle taper Aciera Drilling capacity in steel 22 mm Throat 270 mm Table size 700 x 370 mm Spindle speeds , inf. variable 40-3'600 rpm Iasdpfeuy R T Tsx Adwsl MARCELS MASCHINEN CH

Condition: used, High performance drilling machine ALZMETALL type Abomat 20 Production drilling machine make no. 449 year of construction 1995 drilling capacity in steel ST 60 25 mm drilling capacity in cast iron GG 20 30 mm spindle mounting SK 40 - M16 Iedpfx Adjgd Ipkswsal throat 280 mm drilling slide stroke 500 mm spindle distance max. 685 spindle distance min. 185 table size 490 x 400 mm spindle speed 2000 rpm autom. feed 224 mm/min. rapid traverse 4,5 m/min. motor power feed 0,18 kW motor power rapid traverse 0,75 kW motor power drilling spindle 1,5 kW Mains connection 400 Volt, 50 Hz - Prduction drilling machine with spindle speed and feed rate - actual spindle speed 2000 rpm. - actual feed speed 224 mm/min. - 2 operating modes manual and automatic - electric drill head height adjustment - central lubrication - control cabinet at the rear side of the machine - mounted on steel plate (700 x 650 x 40 mm) with precise height adjustment space requirement L x W x H 1200 x 700 x 2530 mm weight approx. 900 kg good condition

Condition: used, Tube End Forming Machine, T-Drill SP-110, Used Machine Manufacturer: T-Drill Model: SP-110 Operation: Uncertain Overall Dimensions: Width: 930 mm Depth: 1520 mm Isdjxu E Duopfx Adwjal Height: 1460 mm Weight: 600 kg Year of Manufacture: 2016 Air Pressure: 6 bar Electrical Data: 480V; 18.5 kW; 3x80A The T-DRILL SP-110 is a fully automatic tube end spinning machine capable of closing, reducing, and expanding primarily copper and brass tubes — typical applications include HVAC, refrigeration, and mechanical fittings. Technical Data (Summary): Tube diameter range: Ø 8 – 108 mm (≈ 5/16” – 4-1/8” O.D.) – T-Drill Oy Maximum reduction: 70% – T-Drill Oy Materials: primarily copper and brass (as highlighted in the manufacturer’s description) – T-Drill Oy Wall thickness / maximum wall thickness (according to used machine listings): e.g., one listing indicates 0.125" (≈3.2 mm) maximum wall thickness (depends on model/configuration) – Southern Fab Sales Machine features: automatic clamping, rotation + forming tools (tooling/dies), suitable for forming long or complex tube ends. Capable of closing, flattening, reducing, and expanding tube end geometries; the manufacturer’s brochure contains detailed shapes and examples. Especially suitable for HVAC and industrial refrigeration tubes.

Condition: reconditioned (used), Year of construction: 2002, drill gomad WU 3G 2002 YEAR LIGNUM WU drills Drill WU 3G 3 TOP UNITS Flexible task drills with adjustable spacing of top, side, bottom and swivel drilling units equipped with multi-spindle drilling heads. Designed for drilling all kinds of holes. The modular structure provides many configuration options (working length, number of units, pneumatic clamps, etc.). They enable single- and multi-stage drilling and programming the operation of units depending on the needs. Feeding and receiving of the processed material is done manually. Other drilling functions are performed automatically (material pressure, simultaneous 3-sided drilling, pressure release). Spindle spacing scale according to the order 16 - 44 mm Distance between JC head units 250 - 2500mm Width of JG, JB, JC, JS units 160mm Unit feed cylinder stroke JG - 100mm, JB 100 (120mm) Maximum material width 200mm Iodpfx Aji Hqhfedwjal Maximum material thickness 50mm Maximum drilling diameter 35mm Spindle speed 3000rpm JB units spindle center height above table 6 - 35mm (55mm) Drilling unit engine power 1.1 kW Duration of one-stage and two-stage cycle 4 - 6 sec and 6 - 10 sec Air pressure required 0.4 - 0.6 MPa Compressed air demand 2 m3/h per drilling unit Type of feed drive pneumatic with stepless speed regulation Supply voltage 400V, 50Hz Overall dimensions (L x W x H) 2200 - 4000 x 1500 x 2000mm Weight 2500 - 3000 kg Contact the advertiser Przemyslaw Kretowicz is online lignum 602 Show number

Condition: good (used), Nagel Citoborma 280B Paper Drill The device is 100% functional. This is one of the newest models. The drill table is adjustable in every plane (sides, front/back). It has limiters for setting the drilling spacing. The installed table is in an enlarged version. Additionally, the paper drill has an automatic table lock, which is released after each cycle. Ijdpfx Aex Tvliodwsal Super condition. Solid construction – weight 76kg. 380V power supply Two drilling heads, with adjustable spacing within the range of 45-120 mm. Drill diameter 2-20 mm. Stack height 60 mm. The machine has been inspected The set includes drills and tools, a new cutting stick, and an instruction manual.

Condition: excellent (used), Year of construction: 1993, Catalogue number 7718 TECHNICAL DATA - Number of spindles: 23 pcs - Head prepared for screw-in drills - Distance between outermost spindles: 704 mm - Distance between spindles: 32 mm - Pneumatic clamps: 2 pcs - Table surface dimensions: 1200x850 mm - Height to table surface: 930 mm - Feed cylinder stroke: 70 mm - Max drilling diameter: 12 mm - Drilling adjustment vertical/horizontal and at an angle - Drilling unit adjustment pneumatic - Main motor: 2×0.75 kW - Dimensions L/W/H: 1270x1330x1350 mm - Weight: approx. 700 kg ADVANTAGES – Made in Poland – 23 spindles – Head prepared for screw-in drills Ijdsw I R Tijpfx Adweal – Not repainted – DTR technical documentation – Used drilling machine, very good condition Net price: 8900 PLN Net price: 2120 EUR based on exchange rate of 4.2 EUR (Prices may change depending on currency fluctuations)

Condition: excellent (used), Professional drill chuck with SK40 / ISO40 taper, compliant with DIN 69871 A standard. Manufacturer: EROGLU Präzisionswerkzeuge (Germany) – high-precision manufacturing. Model: 03180PB05553 (3/16-IK). Maximum tightening torque: 20 Nm – ideal for drilling and tapping with controlled force. Version with internal cooling (IK – Innenkühlung). Chuck with torque adjustment + / –, allowing protection of tools and workpieces. Solid and durable industrial design – suitable for use in CNC machining centers and conventional machines. Condition: used, in very good technical condition – ready for immediate use. ✅ German quality – precision industrial-grade drill chuck ✅ Ideal for production and workshop applications. Iaodoxlcz Sjpfx Adwjl

Condition: used, Line boring machine WEBO with 4 stations type B 20 make no. 376/13; 376/14; 376/27; 376/36 year of construction approx. 1970 drilling capacity 20 mm spindle adaptor MK 2 - long spindle sleeve drilling head distance 335 mm throat 260 mm pinol stroke 190 mm table size 350 x 1500 mm Iasdpoihmwtsfx Adwjl distance drilling spindle/table min.30 mm / max. 700 mm Spindle speed drill head 376/13 355, 500, 710, 1000, 1400, 2000, 2800, 4000 rpm. Spindle speed drill head 376/14 355, 500, 710, 1000, 1400, 2000, 2800, 4000 rpm. Spindle speed drill head 376/27 250, 355, 500, 710, 1000, 1400, 2000, 2800 rpm. Spindle speed drill head 376/36 180, 250, 355, 500, 710, 1000, 1400, 2000 rpm. Motor power 1,1 / 1,3 kW Mains connection 380 Volt, 50 Hz - Spindle speed via 2 motor speeds and 4 V-belt steps - drill head height adjustment via toothed rack and hand crank approx. 300 mm - height adjustable drilling table approx. 350 mm space requirement L x W x H 1750 x 1100 x 1900 mm weight 1900 kg good condition

Condition: used, Year of construction: 2008, operating hours: 5,834 h, 2008 | Delmag SR 25 BT / RH 18 on Sennebogen SR25 with ABI MDBA 3500 Soil Improvement Rig | Used Drill | 5834 hours 📍Location: Germany 🚛 Delivery available to your destination – Use our shipping calculator to estimate transport costs! 💰 Buy Now for EUR 220000 or Make an Offer. Payment at delivery available for an affordable fee (subject to approval)* 👷‍♂️ Inspected by an independent expert 65 inspection points 65 approved ✅ 0 imperfect ℹ️ 0 issues ⚠️ 📌 Inspector's Comment: The machine is used for concrete pile drilling, soil improvement, and vibration tamping. The carrier vehicle is a Sennebogen SR25BT (built in 2008) with a Delmag RH18 drilling attachment (built in 2009). The drill table lift is 12.50m, total height is 19.91m. The outreach is 3.165 - 4.00m. It includes a winch for the feed with freewheel, auxiliary winch, and rear platform. The drill table is an SHT25, and the KDK rotary drilling head BT180-2 is not included. The machine is purely a soil improvement device, equipped with a MBDA 3500 ABI drill gearbox. It has a single auger. No Kelly bar is included. It features mast support cylinders and alignment automation. The hydraulic telescopic undercarriage has a width that adjusts from 3.0m to 4.40m. The CAT C9 engine was overhauled by CAT in 2015 at 3,304 operating hours. Drills and drill accessories are available separately. Also available is a mobile mixing plant, manufactured by MAT, which includes a mixing container (throughput capacity of 20m3/h), a conveyor screw, a mixing container (capacity 4,000l), and a plunger pump with remote control. The machine’s condition corresponds to its operating hours. During the inspection in 2023, the machine was running and functioning without any issues. As of October 2024, wear and tear have occurred on the valves, controls, and hydraulic hoses. It is not possible to operate the machine with two attachments simultaneously. The machine shows wear on bolts, bushings, and general usage marks (dents, scratches, etc.) consistent with its age, operating hours, and usage. The machine was not tested under load. It has been used with 55 and 80 paddles. After service and maintenance of the wear and tear, the machine will be ready for operation. 📄 Want to see the full inspection, extra photos, or a video? Tip: The reference "33244 Equippo" is commonly used when looking up more details online. 💡 Why this machine and our service stands out: Iedpjx Uyzqjfx Adwoal ✔ Thorough inspection by professionals ✔ Jobsite delivery available ✔ Money-Back Guaranteed ✔ Secure and flexible payment options 🔄 Considering other equipment options? We offer helpful tools and resources for all equipment owners and operators – easily accessible on our platform.

Condition: good (used), Year of construction: 1999, Drill grinding machine, drill grinding device, tool grinding machine, twist drill grinding machine -Manufacturer: CUOGHI AFFILATRICI, drill grinding machine type APE60 with point thinning device -Drill chuck: up to Ø 60 mm -Grinding discs: Ø 200 x 45 x 32 -Coolant system: present -Accessories: incl. tools (see photo) -Dimensions: 860/880/H1300 mm Isdoyab Syjpfx Adweal -Weight: 275 kg

Condition: used, Items as new or nearly new and used wood drills mainly in sizes 10, 13 and 26 mm. Remaining stock of a double-end profiler with drilling assemblies. Isdpfxex Tvbws Adwsal

Condition: excellent (used), CATALOG NUMBER 6608 TECHNICAL DATA - Number of spindles: 21 pcs - Distance between outermost spindles: 640 mm - Spindle pitch: 32 mm - Max drilling depth: 60 mm - Vertical drilling width: 60 mm - Adjustable drilling (up/down and at an angle) - Right/left drill bits, mounted with hex screws - Pneumatic clamps: 2 pcs - Table surface dimensions: 490x1040 mm - Height to table surface: 920 mm - Main motor: 2.2 kW - Operating pressure: 6-8 bar - Dimensions (L/W/H): 2830/1150/1320 mm - Weight: 442 kg - German manufacture - Original DTR documentation - Unpainted - Mobile Net price: 7,900 PLN Net price: 1,880 EUR (based on a rate of 4.2 EUR) (Prices may vary in case of significant fluctuations) Iaodpfsx Sq Amox Adwel

Condition: excellent (used), Professional drill chuck from the renowned brand GEWEFA, made in Germany. Designed for clamping drills with a diameter from Ø2.5 to 16 mm in CNC machines, machining centers, and conventional milling machines. The high-quality construction ensures excellent concentricity, secure tool holding, and long service life even under intensive production work. Type: SK40 × Ø2.5–16. Catalogue number: 28.05.046.002. Taper: SK40 DIN 69871. Manufacturer: GEWEFA – Made in Germany. Year of manufacture: 2007. Condition: very good, used. An ideal choice for professional industrial applications and metalworking workshops specializing in precision machining. Price is per unit. Iodpfoxizausx Adwsal

Condition: used, Vertical milling head, milling head with motor drive THIEL Tool holder: MK 5 (Morse taper size 5) Quill stroke, spindle travel: 80 mm Spindle speed at motor speed 1410 rpm = 490 / 780 / 1200 rpm. Spindle speed at motor speed 2950 rpm = 970 / 1530 / 2380 rpm. Spindle bore: 37 mm Motor power: 1.4 / 1.8 kW Isdpfx Adjxddwrewoal Motor speed: 1410 / 2850 rpm Power connection: 400 Volt, 50 Hz - Spindle speed via 2 motor speeds and 3 belt stages - Mounting flange milling head Ø 215 mm with 2 bores Ø 15 mm, hole spacing 180 mm - suitable for tools with drawbar thread (ejector tang interferes with clamping) Required space L x W x H: 450 x 400 x 350 mm Net weight: 61 kg Good condition

Condition: good (used), Year of construction: 2000, 6 bar pressure with insertion device for cup hinges with 5-hole row, 1.6 kW, 380 Volt. Includes 3 drills for cup hinges and foot switch. Iedox U Di Espfx Adweal

Condition: good (used), Uchida GA-4W Four-Head Paper Drill This machine is in very good condition and ready for operation. Made in Japan. The machine has a number of features that make it easy to use, including: – four drilling heads with independently adjustable positions – a sliding programming bar Ijdpfx Ajx N I Saodwoal – spacers for easy setup for drilling holes Technical specifications: Drill diameter: 2-10 mm, Stack height: 50 mm, Head spacing: 65 mm – 330 mm Weight: 370 kg 380V power supply Automatic drilling cycle, controlled by a foot pedal. Sturdy construction on a pedestal. Waste discharge is directed outwards. Front and side margins. Includes operating tools. New cutting stick, drill bits, and sharpener.

Condition: excellent (used), For sale: professional cutter and drill bit sharpener, model PP U3. Condition: very good, complete unit ready for operation. Included in the set: • Set of grinding wheels • Adjustable angular tool holder • Workshop lamp with flexible arm • Keys and clamping elements Specifications: Iajdpjxdh Hqofx Adwjl • For sharpening cylindrical and spiral end mills • For sharpening step and cylindrical drills • Wheel linear speed up to 35 meters per second • Maximum noise level: 66 dB • Machine weight: 41 kg Solid, stable construction—ideal for precise tool machining. A reliable solution for tool rooms, CNC workshops, and machine shops.

Condition: good (used), Nagel Citoborma 480AB Paper Drill This machine is in very good condition. It has four drilling heads. Technical specifications: Drill bit distance: 45-285 mm Drill diameter: 2-20 mm Stack height: 60 mm Iasdpsx N I H Refx Adwsl Weight: 275 kg Automatic drilling cycle, controlled by a foot pedal. Sturdy construction on a pedestal. The drill table is adjustable in all planes. This is one of the newest Citoborma models. Includes operating tools, instructions, and a new cutting stick and drill bits.

Condition: excellent (used), For sale: Professional WNT tool holder SK40 Ø12x80 capable of operation up to 25,000 rpm (balanced to G2.5). The holder comes complete with a ventilated drill – ideal for machining with internal cooling. Excellent condition, the tool has been tested and is ready for use. Top-class equipment, designed for precision machining on CNC centers. Iajdsw Rrw Uopfx Adwol

Condition: good (used), I SELL FEIN PS 50 MAGNETIC DRILL. IN VERY GOOD CONDITION. Ijdpfsulc Tuex Adwsal

Condition: excellent (used), I sell a HANG 106DTK paper drill, operational in good condition. There are several Hang drills on offer. Iajdpoudpc Sjfx Adwsl

Condition: excellent (used), For sale: professional German paper multi-spindle drill HANG 106 DTK 20. Industrial-grade equipment, ideal for bookbinding shops, printing houses, or the production of binders and calendars. Model: HANG 106 DTK 20 Manufacturer: Constantin Hang Maschinenfabrik Göppingen Number of spindles: 4 Drilling diameters: • Cardboard/paper: up to 3.0 mm • Material samples: 2.5 mm / 6.0 mm / 12.0 mm Drive: PRYM Getriebebau geared motor, 50/60 Hz Stable cast iron construction Adjustable work table Complete machine, ready for operation Technical condition: very good. Used but well-maintained, no play, with original nameplates and operating documentation. Iodeudl Anjpfx Adwoal

Condition: excellent (used), Four-head paper drill. Several pieces available !!! Brand Hang Model 106DTK4 Details 4-head paper drilling machine With adjustable drilling heads Operation Electric foot switch, 2 speeds Available directly This additional information is standard for this model. Always check the details carefully during your visit. The 1975 Hang 100DTK4 printing machine is an iconic and reliable piece of equipment that has made a significant impact on the printing industry. Manufactured by Hang, the machine offers advanced features for its time and set the standard for high quality and efficient printing. Ijdpfx Aeudl Ikedweal The Hang 100DTK4 features a robust and durable design, ensuring stability and consistent performance during the printing process. Its printing technology, although conventional by today's standards, allowed for precise and sharp prints with satisfactory resolution for its era. Equipped with user-friendly controls and mechanical automation, the machine offered programmable settings for various printing formats and configurations. Its operation required skilled operators who were able to achieve accurate and repeatable printing results. The printing machine's capabilities extended to a variety of substrates, including paper, paperboard and lightweight cardboard, satisfying a range of printing applications common at the time. Launched in 1975, the Hang 100DTK4 presented a technological advance for its era. Its sustained performance and contribution to the printing industry are remarkable. While newer printing machines with advanced digital technology have emerged, the Hang 100DTK4 remains a historic symbol of performance and innovation in the printing industry in the 1970s. The machine has collector's value and serves as a testament to the evolution of printing technology over the decades.