Used Plasma Cutter for sale (3,194)

Condition: used, Plasma cutting machine MB - Welding Technology, Type Plasmaprof 50 Rjdpodzqa Hsfx Ap Ejcf Identical construction to CEBORA Machine no. 244311, year of manufacture approx. 1992 Output: 50 amps = 35% duty cycle 30 amps = 100% duty cycle Setting range: 2 levels Hose pack length: approx. 6 meters Compressed air connection: 4.7 bar Mains connection: 400 volts, 50 Hz, 32 amp plug Space requirement L x W x H: 500 x 350 x 700 mm Weight: approx. 80 kg In good condition

Condition: as good as new (ex-display), Year of construction: 2022, operating hours: 1 h, functionality: fully functional, machine/vehicle number: 285033, type of input current: three-phase, input voltage: 400 V, type of cooling: air, overall weight: 25 kg, electrical fuse: 32 A, cutting current: 105 A, hose package length: 6,000 mm, sheet thickness steel (max.): 50 mm, air demand: 15 m³/h, air pressure: 5.8 bar, protection type (IP code): IP23, product height (max.): 50 mm, High-end air plasma cutter for manual cutting. Although the system is equipped with a manual cutting torch, it can also be used for mechanical cutting. The interface for CNC cutting is already installed The manual cutting torch with a length of 6 meters is included in the scope of delivery. Rcedpfx Apjrq E R Uo Ejf The system was operated in our application center for demonstration purposes. The system has an effective cutting time of less than 30 minutes. Further technical information can be found in the attached document / data sheet

Year of construction: 1989, condition: good (used), Operating hours: 17 Rcodpfxobfa Hwo Ap Ejf Machine number: 160973 Power: 4,500 W Voltage: 220 V No-load voltage: 320 V Current: 16 A Insulation class: F Cooling type: F

Condition: ready for operation (used), Year of construction: 2010, operating hours: 9,000 h, functionality: fully functional, machine/vehicle number: 714000-1, type of input current: three-phase, input voltage: 400 V, table length: 7,000 mm, table width: 2,000 mm, power: 36.77 kW (49.99 HP), Flow Waterjet 714000-1 Flying Bridge 7x2 meters Year of manufacture: 2010 60,000 PSI 9,000 hours Complete and in good working condition Various wear parts such as pipes and extra nozzles Abrasive hopper Abrasive feeder Immediately available Waterjet cutter Flow Waterjet Flowcut Waterjet cutting OMAX CNC plasma Hypertherm Laser fiber laser bystronic Amada Trumpf Accurl Bodor HSG JQ Nukon Rsdpsxwtu Tefx Ap Ejcf

Condition: new, neu ca. 12 - 14 Wochen ab Auf Türkei 163101 € 3082.61 € 2000x6000 mm Hypertherm XPR 170 CORE 60 mm 38 mm 38 mm 35 mm 22 mm 25 mm 170 A 12 m/min 35 m/min +/- 0,1 mm 0,1 mm 6000 kg HyPerformance plasma power sourceHyperthermXPR 170 COREWITH "TRUE HOLE" TECHNOLOGY Automatic gas console Plasma torch height control Collision protection (torch brake away system) CNC control with Aurora Software Lantek CAD/CAM software with auto nesting Control of filter unit by CNC Redewiq Hajpfx Ap Ejcf Remote control diagnostic by Ethernet Cutting plate alignment function User manual in GERMAN or ENGLISH Options: Suction with filter Morepricefor Optimix instead of Core Further options as CNC bevel head, drilling head, oxyfuel torch, Durma cloud etc. on request.

Year of construction: 2007, condition: used, functionality: fully functional, The temperature control unit from Plasma/Single is for sale; there are 2 units available for sale, and the price is per unit! Medium: Oil Maximum operating temperature: 180°C Heating capacity: 6 kW Cooling capacity: 14 kW External cooling fan... Rodezul N Rjpfx Ap Eecf PT 100 sensor Interface 0-20 mA

Condition: new, Year of construction: 2024, functionality: fully functional, machine/vehicle number: 170.012.100, Brand new Holmatro hydraulic shears. Perfect for auto recyclers, for cutting catalytic converters, etc. Rjdpfjzcyrwox Ap Ejcf The shears are brand new, manufactured in 2024, but have never been used. Includes a complete service kit.

Condition: excellent (used), Cutter Stephan UM 12 Rcsdpfx Aezwmtpop Eof stainless steel. Capacity: 12L Blade speeds: 1400 rpm / 2800 rpm Timer: 0 - 360s Voltage: 400V (3+N, 50Hz) Power: 1.9 kW Weight: 60 kg Machine dimensions in mm (W x D x H): 550x350x1230 mm

Condition: ready for operation (used), functionality: fully functional, Fatosa Frozen Meat Slicer, Frozen Blok Cutter Redpfx Ajzmp Rpjp Ejcf Sold on behalf of a customer – functioning machine, sold as is, without warranty, no returns.

Condition: used, Year of construction: 2017, functionality: fully functional, input voltage: 400 V, input current: 16 A, total width: 1,400 mm, total length: 1,500 mm, machine base height: 1,400 mm, overall weight: 350 kg, Hello, I am offering a used Corona / Plasma treatment system for sale. The material to be treated is placed on a conveyor belt. Sensors automatically activate the plasma / corona discharge when the substrate is positioned beneath the head. The feed speed is adjustable. The conveyor belt has a width of 650 mm. The system is mounted on casters, making it mobile. An exhaust fan is also installed and only the exhaust air needs to be ducted outside. This system is ideal for treating the surfaces of plastic materials or glass to improve printability. It is also suitable for the pretreatment of materials to enhance adhesion for bonding. Rjdoy A Trlepfx Ap Eecf If you have any questions, please feel free to contact me.

Year of construction: 2012, condition: used, functionality: fully functional, The temperature control unit from Plasma, model "Primus", is available for sale with the following technical specifications: Medium: water, Maximum temperature: 150°C, Heating capacity: 9 kW, Cooling capacity: 30 kW, Special equipment: reinforced pump K6 at 60 l/min up to max. 6 bar. The pressure booster pump is used to increase the cooling water pressure during filling; this is necessary if the system pressure is higher than the cooling water pressure. PT 100 sensor. Interface: On/Off, Alarm, PT 100, Temperature monitoring. Rcjdex Eg T Eepfx Ap Eof

Condition: like new (used), Cutter CFS GEA CutMaster 500 VACUUM Rcodeyn Dy Nspfx Ap Eef After capital renovation 3 months warranty for parts

Condition: good (used), Please refer to the images for all technical specifications. Transport and loading can be arranged throughout Europe for an additional charge upon request. Rcodpfx Apezvnnfs Eof Prices are subject to VAT. Viewing is possible by appointment. Contact us—our team looks forward to assisting you. Machinery purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES, MACHINE TOOLS, AND MUCH MORE. Do you need a high-quality yet affordable machine for your production? Or are you looking to sell yours? For further information or contact options, please reach us via the contact form.

Condition: ready for operation (used), Year of construction: 2016, functionality: fully functional, machine/vehicle number: 11139737, sheet thickness (max.): 30 mm, working width: 2,000 mm, working length: 6,000 mm, empty load weight: 1,950 kg, The machine will be available starting mid-September! TECHNICAL DETAILS Working area: 6,000 × 2,000 mm Working length: 6,000 mm Working width: 2,000 mm Max. sheet thickness: 30 mm Travel range X-axis: 6,000 mm Travel range Y-axis: 2,000 mm Travel range Z-axis: 150 mm MACHINE DETAILS Plasma source: Kjellberg HiFocus 161 neo Cooling type: Water Voltage: 3 × 400 V Rjdpfozv N Hpex Ap Eocf Power: 9 kW Frequency: 50 Hz Number of phases: 3 Net weight: 1,950 kg EQUIPMENT Dust extraction system: Donaldson Torit DCE

Condition: good (used), Double side corner cutter Very good condition. This is a professional, production device for rounding corners. Solid construction ensures precision of operation. Two trimming heads. Rcsdpjztpbbsfx Ap Eof Interchangeable knives. Adjustable margins. Controlled by foot pedal. One set of 8mm knives included Stack height approx. 80mm Weight 100kg Efficiency 20 cycles/min Compressed air supply.

Condition: repair required (used), Year of construction: 2010, operating hours: 7,700 h, functionality: not functional, machine/vehicle number: 15158-10, working range: 4,000 mm, sheet thickness (max.): 12 mm, sheet thickness steel (max.): 12 mm, CNC plasma cutting system BACH ThermoCut 2000 with pipe cutting device, TEKA dust extraction system, and plasma source. Manufacturer: BACH Maschinenfabrik GmbH Type: ThermoCut 2000 Year of construction: 2010 For sale is a used CNC plasma cutting system BACH ThermoCut 2000, including pipe cutting device, plasma source, dust extraction system, and complete piping. The system was used in our machine manufacturing company until recently and is suitable for cutting sheet metal as well as processing pipes. Technical data: Working area: 4,000 x 2,000 mm Plasma source: Thermal Dynamics Ultra-Cut 100 CNC control: myBach Pipe cutting device included Pipe diameter: Rsdpfx Apjzizkys Ejcf min. 50 mm max. 320 mm Max. cutting thickness: Mild steel: up to 12 mm Stainless steel: up to 10 mm TEKA filter and dust extraction system included Complete dust extraction piping system included CE marking available Maintenance and condition The system was regularly maintained during its entire service life. Official maintenance by the manufacturer was last performed on August 20, 2013. After that, ongoing maintenance was carried out in-house. Filters of the TEKA dust extraction system were renewed approximately 6 months ago. Cutting torch head was renewed approximately 4 years ago. Cooling water filter is changed regularly, approximately once a year. The operating hour counter of the dust extraction system currently shows approximately 7,700 hours. Since the system was operated exclusively with the dust extraction system running, this value can be used as a good indication of the total operating time of the system. Known defect The system is currently not operational. After consultation with Voortman and Mr. Sobiech from Magma Industries, the cause is likely to be in the cooling circuit of the plasma source. According to the experts, the most likely causes of the fault are: Defective cooling water pump Defective flow sensor Leakage on the suction side of the cooling water system A final fault diagnosis has not yet been carried out. Spare parts for the installed Thermal-Dynamics plasma source are now only available to a limited extent. The machine is therefore explicitly sold as a system requiring repair or for refurbishment. Scope of delivery BACH ThermoCut 2000 CNC system Thermal Dynamics Ultra-Cut 100 plasma source Pipe cutting device TEKA filter and dust extraction system Control panel with controller Dust extraction piping Accessories according to existing equipment Special features ✅ Pipe cutting up to Ø 320 mm ✅ Complete package including dust extraction ✅ Solid industrial machine made in Germany ✅ Easy-to-disassemble gantry design ✅ Also interesting for buyers who already have a suitable plasma source Location 24161 Altenholz, Germany Price Negotiable €21,900 Inspection possible by appointment. Sale exclusively to commercial businesses, excluding any warranty for defects. Loading / Dismantling The system is offered exclusively for self-dismantling and self-collection. The buyer assumes full responsibility for the dismantling, loading, and removal of the machine at their own cost and risk. To assist with loading, a hall crane with a maximum lifting capacity of 10 tons is available on site. Use of the crane can be arranged in advance. Due to the size and weight of the system, we recommend an inspection before submitting an offer.

Condition: used, Year of construction: 2016, BEVEL head - 5 axes SIDEROS table with dimensions 4000 x 6000 mm SIDEROS ECO16CT external filter Rcjdpjzw Nmxefx Ap Ejf COLLECTION BY SEPTEMBER 2026

Condition: new, Year of construction: 2024, NEW Plasma Cutting Machine. Dimensions: 3,000 mm x 1,500 mm Max. steel cutting thickness: 22 mm Max. stainless steel cutting thickness: 12 mm Supplied with CAD CAM software. Rcsdpfotu E Duox Ap Ejf DWG and DXF data transfer via USB and network card. CE certification. ISO 9001, GB/T 19001. 120 A generator. The operational cost is extremely low – only 5.5 kW and compressed air!

Condition: good (used), Year of construction: 2019, functionality: fully functional, Table surface: 7,500 x 2,500 mm Positioning speed: 40,000 mm/min Positioning accuracy: = 0.06 mm/min Repeatability: 0.05 mm/min Machine weight approx.: 2,300 kg MicroStep CNC cutting system of the MG series with the following features: - Hypertherm® XPR170™ plasma power source with automatic OptiMix™ console - Plasma rotator for weld preparation - Fully automatic oxy-fuel torch - Fully automatic drilling spindle MG-40-P26 with 26.8 kW - Steel portal driven and stiffened on both sides for a clear and precise cut - AC servo motors from Panasonic for high drive power and excellent dynamics - Durable and low-maintenance planetary gearboxes - User-friendly machine control - High reliability and long service life, even in three-shift operation - MicroStep iMSNC® machine control with MMI console and 24" touchscreen - iMSNC® module | User management - iMSNC® module | Expert system - iMSNC® module | Automatic calibration of mechanical sensing - iMSNC® module | Visualization of wear parts - iMSNC® module | Assistant for loading CNC programs - iMSNC® module | Management of cutting programs (MRP) - iMSNC® module | EcoInfo - iMSNC® module | MachineInfo - iMSNC® module | Assistant for service and maintenance operations - USB 3.0 connection for storage media - Remote maintenance module MicroStep RemoteDiagnostics® - Remote maintenance access via TeamViewer - Two LCD control units on the portal - Laser pointer with automatic offset transfer - Hypertherm® XPR170™ plasma power source - Industry-leading cut quality - X-Definition - Advanced HyDefinition technology - Automatic gas console | OptiMix™ - CNC interface for the Hypertherm® XPR170™ Connection to the CNC control - Module for automatic power control of the Hypertherm® XPR170™ - Electrical and mechanical torch sensing Rjdszwl Dmjpfx Ap Escf - Remote activation of plasma power source - Double-sided cable protection (collision protection) of the portal bridge via emergency stop - Extraction table system with oscillating conveyor OXYtrac 2580 HD Main components and dimensions: 1 Table consisting of: 4 table elements WxLxH (mm) 2,600 x 2,080 x 950 Total support area: WxLxH (mm) 2,600 x 8,320 x 950 Contiguously usable working area per table: Vertical cutting: WxL (mm) 2,500 x 8,000 Bevel cutting: WxL (mm) 2,000 x 8,000 Table width (outer): W (mm) 2,830 2 Oscillating troughs L (mm) approx. 8,900 Cutting processes and associated extraction capacity: 1x Plasma max. 170 Amp., bevel cutting 1x Oxy-fuel max. 100 mm workpiece thickness regularly 200 mm workpiece thickness occasionally

Condition: used, Bertuetti Universal Dough Cutter. In working condition. With two dusters. Belt 400mm wide One additional cutter included. Rcsdotpvt Tepfx Ap Eef Price € 590 We can organise shipping if you require this service

Condition: refurbished (used), Year of construction: 2010, functionality: limited functionality, Alpina Swopper 330 litre Bowl Cutter Year 2010 Motor power 141 Kw Multispeed knife and bowl Noise cover Power up knife lid 6 x knives Unloader disc Tote bin loader Currently being refurbished New knife shaft bearings fitted Hydraulic rams being checked and new seals fitted Main motor being rewired, machine stripped out to clean. 6 x knife speeds with 2 x reverse knife speeds Rsdpfeykt Sgox Ap Ejcf 4 x bowl speeds With machine manual and drawings

Condition: good (used), Year of construction: 2020, functionality: fully functional, type of input current: three-phase, total width: 4,500 mm, total length: 4,500 mm, input voltage: 400 V, working width: 2,000 mm, cutting width (max.): 2,000 mm, We offer a camera-assisted CNC cutter for single-layer cutting of textiles and leather. With the integrated image processing system, shapes and designs can optionally be recognized and cut with precision. The machine has low operating hours and is in perfect working condition! Rcsdpfx Apsyx I Due Esf

Condition: not inspected (used), Year of construction: 1989, functionality: unexamined, input voltage: 1,200 V, Industrial paper rewinder and cutter KAMPF (KAMPF GmbH & Co., manufacturer Jagenberg-Gruppe, Germany) Rcodpfx Apjztwuvj Esf Technical data: • Manufacturer: KAMPF GmbH & Co., Maschinenfabrik, Wiehl (Germany) • Group: Jagenberg-Gruppe • Year of manufacture: 1989 • Serial number: 9791D • Machine type: industrial paper roll rewinder and cutter • Power supply: 3 × 400 V • Machine location: Papir – Novak s.r.o., Czech Republic Use of the machine: The machine is designed for rewinding and longitudinal cutting of roll materials, in particular: • paper, • kraft paper, • wrapping paper, • technical papers, • other similar strip materials. Machine components: • unwinding stand for the parent roll, • main rewinding and cutting unit, • guide and transport rollers, • winding shafts, • protective cover for the cutting section, • control panel, • mechanical tensioning using an Ortlinghaus clutch. Machine condition: • mechanically complete, • the machine was dismantled from operation and stored in a dry warehouse for a long time, • the unwinding stand is included, • the control panel is installed, • functionality has not been verified – the machine is untested, • it is sold in its current condition, • suitable for reconditioning, commissioning, or as a source of spare parts.

Condition: good (used), Year of construction: 2019, functionality: fully functional, Brand: Grotius Control system: Linux CNC Working area: 3000 x 1500mm Length (mm): 4020mm Width (mm): 2330mm Height (mm): 1570mm Rsdezupvuspfx Ap Escf Description: Includes Thermal Dynamics A40i plasma source & various wear parts.

Condition: used, Year of construction: 2004, functionality: fully functional, machine/vehicle number: 403/05, table length: 3,000 mm, power of the servo motor: 1,500 W, table width: 1,500 mm, Equipment: double-sided, With plasma cutting system HyperTherm Powermax 1100 and air drier M.T.A. DE009 Machine was used in the production of ventilation ducts and fittings. Rsdpfx Apow I D Iao Eecf AsperWin (base program for operating CNC machine for Windows. Dxf-files can be imported) Asper Nesting (enables effective creation of nests with a big number of different cut parts to achieve best possible utilization of material with minimum waste) and Air Select (for ductwork manufacturers enables fast and comfortable design of HVAC components).