Used Plasma Oxygen Cutting for sale (14,165)

Condition: good (used), Year of construction: 2016, functionality: fully functional, Microstep Mastercut Eco Plus 3001.15 Year of manufacture: 2016 Controller: IMSNC Cutting table: 3000 x 1500 mm Extraction channel left/right Plasma source: Kjellberg HiFocus 161i, adjustable 10 – 160 A Power Source HiFocus 161i PLUS • Flexible adaptation of the cutting process to required conditions thanks to soft-switch inverter and microprocessor control • Optimal process management with ultra-fast regulation of cutting current • Process monitoring for torch cooling, ignition time, pilot arc time, short-circuit time during torch ignition, and the power source • Display of operating statuses and error messages via LED and display • Analog and serial interface for adaptation to CNC controls • Infinitely variable adjustment of cutting current from 10–160 A; marking current from 5–25 A • Optimal piercing due to stepless delay time for main arc and adjustable current rise • Adjustable current reduction at corners, as well as at start and end signals from guidance systems • Automatic display of preset cutting current • Serial data transfer for PC-based diagnostics Plasma Cutting Technology Contour Cut • Further development of HiFocus technology for carbon steel • Optimized for cutting fine internal and external contours • High cut quality and contour precision • Holes with angle tolerances according to DIN EN ISO 9013 within range 2-4 • Low angle deviation and smooth cut surfaces • Very good repeatability and dimensional accuracy • No time-consuming post-processing—high productivity, reduced costs • No additional equipment or software required, and no new wear parts necessary • Supplied as standard Plasma Torch PerCut 200/210 • PerCut 200 machine plasma torch for standard applications and high-precision bevel cutting • Quick-change torch PerCut 210 with threaded connector for fast and comfortable setup • Special torches available for custom applications • Higher cutting speeds reduce cost per meter cut • Long service life of consumables conserves resources • Narrower kerf for less emission and waste • Significantly lower gas consumption compared to the competition through efficient liquid cooling up to the nozzle tip • Lower noise level due to reduced gas consumption • Bevel cutting up to 50 degrees with standard consumables • Cutting and marking possible with the same consumables Technical Data: Power source: HiFocus 161i Connection voltage: 400 V; 3-phase; 50 Hz Max. power consumption: 28 kVA (100% duty cycle) Line fuse: 50 A (slow-blow) Nljdpfxsyzy S Ao Akfsa Protection class: IP 22 Open circuit voltage: 330 V Cutting current: 10–160 A (100% duty cycle) Marking current: 5–25 A (100% duty cycle) Cutting range: max. 50 mm, recommended 0.5–38 mm Max. piercing thickness: 30 mm Weight: 206 kg Plasma Machine Torch: PerCut 200 Quick-change torch: PerCut 210 Clamping diameter: 50.8 mm Plasma gases: O2, N2, Ar/H2 Marking gases: Ar Swirl gases: O2, N2, air, N2/H2 (F5)

Year of construction: 2007, condition: ready for operation (used), - USED - CNC PLASMA CUTTING MACHINE WORKING AREA: 6000 x 2000 x 60 mm GENERATOR: HYPERTERM HPR130 CONTROL UNIT: GASPARINI MAX CUTTING SPEED: 0,1 - 30 m/min WEIGHT: 4400 Kg OVERALL DIMENSIONS: 6910 x 3150 x 1581 mm ACCESSORIES: FUME EXHAUSTER NOTE: MACHINE REVISED IN 2026 Nljdpfxsyru Rge Akfea

Condition: good (used), Year of construction: 2016, Gebruikte plasmasnijmachines van Soitaab (Italië) Nlodpfx Akoyu Splsfoa Model: Plasmatech 3015 Tafelafmetingen: 3000 x 1500 mm Hypertherm HPR 130 XD plasmabron Markeerstift Torit afzuigsysteem Bouwjaar: 2016

Condition: good (used), Year of construction: 2007, functionality: fully functional, type of input current: three-phase, working range: 3,000 mm, sheet thickness (max.): 40 mm, The information was found successfully. Here is the updated listing with added cutting parameters: Teknohaus Thermcut 3000D – CNC Plasma Cutting Machine For sale: a well-maintained Finnish-made CNC plasma cutting machine. The machine has been used in production and operates flawlessly. Technical specifications: Manufacturer: Suomen Teknohaus Oy Njdpfxjywlh Us Akfola Model: Thermcut 3000D Year of manufacture: 2007 Serial number: 320011 Supply voltage: 3 × 400 V Plasma source: Hypertherm HyPerformance HPR130 (130 A) Controller: Thermcut / Teknohaus CNC controller with touchscreen USB interface for program transfer Cutting capacity (mild steel): - High-quality, virtually dross-free cut: 16 mm - Production piercing: 25 mm - Maximum cutting thickness (edge start): 38 mm Features: - Large cutting table (approx. 3000 mm wide) - Two plasma channels (Plasma 1 & Plasma 2) - Water table for spark and fume management - Ideal for cutting steel, stainless steel, and aluminium Machine viewings available by appointment; the machine can be seen in full working order. 📞 For further information, please call.

Condition: ready for operation (used), Year of construction: 2021, This ESAB Suprarex HD 4000 plasma cutting machine was manufactured in 2021. It features a track width of 4000 mm and a track length of 12000 mm, supporting a maximum working length of 9000 mm. The machine is equipped for both oxyfuel and plasma cutting, handling material thicknesses up to 200 mm. If you are looking to get high-quality cutting capabilities, consider the ESAB Suprarex HD 4000 machine we have for sale. Contact us for more information. Nsdpfxjx D D N Ue Akfela Application Types Cutting

Condition: used, Year of construction: 2019, functionality: fully functional, Plasma Cutting System Becky Job Master 6.20 with Extraction Table – Year 2019 This plasma cutting system is being sold due to an upgrade to a laser cutting machine. The machine is fully operational and can be inspected and tested under power. Location: Vorarlberg Technical Data Manufacturer / Model: Becky Job Master 6.20 Year of Manufacture: 2019 Nljdpfxsx U Dqio Akfsa Working Area: 6,000 × 2,000 mm Z-Axis Travel: 300 mm Max. Cutting Speed: 75 m/min Dimensions: Machine Length: 8,000 mm Machine Width: 3,700 mm Overall Height: 2,000 mm Work Table Height: 820 mm All accessories belonging to the system are included, such as: Hypertherm XPR 170 power source Donaldson filtration unit Software etc. Sale excludes disassembly, transport, and installation.

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, working range: 6,000 mm, sheet thickness (max.): 35 mm, track width: 2,000 mm, table length: 6,000 mm, cutting current: 260 A, We offer for sale a used, reliable, fully functional Messer Multitherm eco 3100 plasma cutting machine, year of manufacture: 2013. Manufacturer: Messer Model: Messer Multitherm eco 3100 Year of manufacture: 2013 Condition: ready for use Machine type: plasma cutting machine Nedpfx Aoyvgdyekfela Available for pickup: 08/2026 Description: Power source: 260 A Table size: 2 x 12 m Cutting up to 35 mm sheet thickness Software: Omniwin 2025 Regularly serviced Pre-prepared for oxy-fuel cutting Test run possible upon agreement If you have any questions or need more information, feel free to write us a message or call us.

Condition: excellent (used), I sell plasma cutter hypertherm powermax 800 d very good condition. /////Price listed for 1 pc ///// Plasma cutter Hypertherm Powermax 800 Nodpfx Asulc Ixekfjla Plasma cutter description The Powermax800 plasma cutting system uses an inverter power supply to provide a smooth DC output voltage for superior cutting and gouging of mild steel, stainless steel, aluminum and other metals. The Powermax800's power supply provides a constant output current that varies from 20 to 50 amps, providing optimal performance for all metal thicknesses up to 1/2 inch (12 mm). At 50 amps, the Powermax800 can cut metals up to 3/4 inch (20 mm) thick and cut metals up to 1 inch (25 mm) thick.

Year of construction: 2002, condition: refurbished (used), Cutting table / Plasma cutting gantry Brand: SATO Model: SATRONIK HD 8000 Year 2002 Number of heads: 2 - 1 Kjellberg FineFocus 800 cutting head - 1 Kjellberg FineMaker marking head with PB-M25 W torch Maximum wide cutting capacity: 6,000mm Maximum length wide cut: 24,000mm Controller: SATOCNC 3000 Cutting equipment information: Brand: Kjellberg Model: FineFocus 800 Maximum cutting capacity: 80mm Nodpfxehzbi Ns Akfjla Cutting quality up to: 60mm Maximum drilling capacity: 40mm Maximum current at 100%: 300A Automatic gas console

Condition: good (used), overall weight: 2,400 kg, OXIPLASMA Kompak EKO 3100x1600mm Plasma Cutting Table Brand: OXIPLASMA Model: Kompak EKO 316 Nljdpswlrukefx Akfsa Manufactured: 2018 (Installed at client for operation in 2021) Description: Useful cutting capacities: 3,100x1,600mm Travel speed: 30 m/min Positioning accuracy: +/- 0.1 mm Motorization: Brushless servos (4 interpolated servo motors (x, y1, y2, z)) Double guidance and traction system Height control managed by the CNC Anti-collision detector with inductive electromechanical impact control Suction table sectioned by zones using the CNC Hypertherm EDGE CONNECT CNC 19" touchscreen Useful head lift: 120 mm Weight: 2,400 kg Cutting capacity: Carbon steel: 32 mm Stainless steel: 20 mm Includes: - Hypertherm HPR 130 XD high-definition plasma equipment - Hypertherm gas console - ROLLAIR RLR 700 screw air compressor, 7.5 HP, year 2007, 10 Bar 5,402 hours - BEKO DryPoint RA air dryer

Condition: used, Year of construction: 2020, functionality: fully functional, type of input current: three-phase, working range: 9,000 mm, sheet thickness (max.): 100 mm, overall weight: 1,100 kg, input voltage: 400 V, total width: 3,500 mm, cutting current: 154 A, input frequency: 50 Hz, We are offering this used MicroStep 9001.35P plasma cutting machine, year 2020. Type: MasterCut Model: 9001.35P Serial No.: 2815 Year of Manufacture: 2020 Nljdpfx Asyu Hkwjkfoa Rated Current: 154 A Short-Circuit Current: 6 kA Weight: 1,100 kg IP Protection: 43/20 Power Supply: 3L+N+PE AC 400/230V, 50Hz If you have any further questions or require more information, please send us a message or give us a call.

Condition: like new (used), Year of construction: 1991, functionality: fully functional, machine/vehicle number: 176063, table length: 4,000 mm, table width: 2,000 mm, Plasma cutting machine CORTA PS 3100 Year of construction 1991/retrofit, machine number: 176063 Cutting area: 4000 x 2000 mm Alternating operation of 2 cutting processes: 1x plasma cutting unit Stak Pak ll, 105 Ampere 1x oxyfuel cutting torch MG 12 SE 30 CPS control unit DNC connection Graphic base version Trajectory: 6000 mm 1 torch suspension MG 200 K arc-dependent scanning 1 plasma interlock Nljdpfevfmiwex Akfja Portal carriage, cross carriage Torch suspension MG 200 K Cutting table 4200 x 2100 x 700 mm Modular, technically advanced Stak Pak II plasma cutting system, 105 amps 1 control module CM 6032 3 power modules PM 6042 1 PCM 35 torch, 15 m 1 PCM 140 torch, 15 m 1 cooling module ex works

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: 20 40 27.07 / 207 - 090, type of input current: three-phase, Plasma cutting machine OMNICUT 4000 Control unit MS 100 Air extraction system Specifications: Rail length: 15 m Table length: 12.5 m Rail span: 4 m Table width: 2.6 m Plasma cutting unit HPR 130 Cutting thicknesses: Steel: 0.5 mm – 25 mm Stainless steel: 1 mm – 20 mm Aluminium: 1 mm – 20 mm Nedpfx Akjyr Iguofjla Oxy-fuel cutting unit MSX 750, PCS 2100 Steel: 3 mm – 300 mm The machine has seen little use and is offered in full working condition, ready for operation.

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, operating hours: 240 h, control type: CNC control, controller manufacturer: Hypertherm, controller model: Edge Connect TC, sheet thickness steel (max.): 40 mm, working length: 3,000 mm, working width: 1,500 mm, positioning accuracy: 0.05 mm, repeat accuracy: 0.05 mm, workpiece weight (max.): 5,000 kg, warranty duration: 12 months, Used Esprit Automation CNC Plasma – High Definition XPR170 Nlsdpfx Aoyzuw Tekfea This Esprit Automation CNC plasma cutting system is presented in exceptional, near-new condition with less than 300 operating hours. Built for precision and reliability, this machine is equipped with a Hypertherm XPR170 high-definition plasma system, delivering superior cut quality and performance across a wide range of materials. Key Specifications: Cutting Area: 3000 x 1500 mm Plasma Source: Hypertherm XPR170 (High Definition) Gas System: VWI Gas Module Included Piercing Capacity: Up to 40 mm Mild Steel Operating Hours: < 300 hours Condition: The machine is in pristine condition, having seen minimal use in a controlled environment. Fully maintained and ready for immediate operation. Additional Information: 12-month parts warranty included Ideal for high-precision fabrication, engineering, and production environments Excellent opportunity to acquire a premium CNC plasma system at a fraction of new cost

Condition: used, Year of construction: 1997, open-circuit voltage 280 - 320 VDC current intensivity 30 - 80 A output voltage 140 VDC cutting medium Air / Nitrogen total power requirement ca. 11,2 kW weight of the machine ca. 40 kg dimensions of the machine ca. 0,90 x 0,35 x 0,50 m Plasma Cutting Machine HYPERTHERM - Hypertherm Powermax 1100 ERTHERM RT 80 hand torch - Recommended cutting capacity: 22 mm - Maximum cutting capacity: 29 mm - Severing capacity: 38 mm Nlodpfx Akoym D Ansfoa - Gas: Air or nitrogen - Gas inlet pressure: 6.1 bar - Gas flow rate: 189 l/min

Condition: used, Plasma cutter CLOOS type CPS 40/80 Year of manufacture 1990 Power at 60 % ED 80 Amp. Power at 100 % ED 40 Amp. Nledpfx Ajdzqccskfoa Adjustment range 40 and 80 Amp (2 steps) cutting capacity with steel max. 25 mm Hose package length 5.5 meters Mains connection 400 Volt with 32 Amp. Plug - Hand torch CLOOS dimension L x W x H 700 x 600 x 750 mm weight 160 kg good condition

Condition: used, Plasma cutting unit MB - Welding Technology Type Plasmaprof 50 Equivalent to CEBORA Machine no. 244311 Year of manufacture: approx. 1992 Power: 50 A = 35% duty cycle 30 A = 100% duty cycle Adjustment range: 2 steps Torch hose length: approx. 6 meters Compressed air connection: 4.7 bar Power supply: 400 Volt, 50 Hz, 32 Amp plug Installation dimensions (L x W x H): 500 x 350 x 700 mm Njdpfx Akjdzqa Hsfola Weight: approx. 80 kg Good condition

Condition: used, Year of construction: 2012, operating hours: 7,500 h, functionality: fully functional, type of input current: three-phase, sheet thickness (max.): 35 mm, sheet thickness steel (max.): 35 mm, sheet thickness aluminum (max.): 30 mm, overall weight: 1,500 kg, input voltage: 400 V, total width: 4,000 mm, total height: 2,000 mm, total length: 8,000 mm, cutting height (max.): 110 mm, track width: 2,950 mm, Equipment: documentation/manual, Selling an Oerlikon plasma cutting system, Plasmatome 20 HPC, Nertajet HP 300 plasma source with CPM 400/450 torch heads for aluminum, steel, and stainless steel. Cutting range 2 x 6 m, cutting current 30-260 A, power consumption 80 kVA. Material thickness of the sheets to be cut with piercing up to 35 mm, external thickness up to 50 mm. Sold without cutting table. Nedpfx Ajv I U Hcjkfjla

Condition: excellent (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: EN 60204-1, sheet thickness (max.): 20 mm, sheet thickness steel (max.): 20 mm, sheet thickness aluminum (max.): 10 mm, cutting height (max.): 20 mm, table length: 3,000 mm, working width: 1,500 mm, table width: 1,500 mm, warranty duration: 12 months, working length: 3,000 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, height adjustment type: electric, We are offering this well-maintained Hugong INTECUT-HT plasma cutting machine / CNC portal cutting system KAI-TEC Smart, including marking function, year of manufacture 2025, as we are upgrading to a larger system. The machine was only purchased for a single project and has been in operation since August 2025. The manufacturer’s warranty is valid until August 2026. The system is fully functional, in excellent technical condition, and shows no signs of excessive wear. Only normal signs of use are present. It has become too small for our requirements, but it is ideally suited for smaller metal workshops, metal construction companies, or fabrication shops. Technical data & features: - CNC portal cutting system KAI-TEC Smart - Cutting area: approx. 1,500 × 3,000 mm - CNC control with cutting database - NEOCUT 105 plasma system with marking function - Plasma cutting range: 1–20 mm mild steel (stainless steel & aluminium max. 10 mm) - Machine torch including hose package - Automatic torch height control - Laser pointer - FastCam7 nesting software - DXF / DWG import Nljdpfx Aeyux Hqskfoa - Auto-nesting function - Remnant sheet nesting - Cut cost calculation Accessories: ✅ Spare and consumable parts included (e.g. nozzles, electrodes and other accessories – ready for immediate use) Other: - Sale due to new installation - Viewing and test run possible by arrangement - Collection by buyer - Price plus VAT Legal notice: The sale is made with exclusion of liability for material defects. No warranty, no guarantee, no returns. If you have any questions or need further information, feel free to send us a message or give us a call.

Condition: ready for operation (used), Year of construction: 2018, This KERF RUM 2500P plasma cutting machine was manufactured in 2018. It features a large cutting area of 15000mm x 2000mm and is equipped with two bridges, each with 275amp plasma. Full history from the manufacturer is available. Contact us for more information about this machine. Nlodpox Hbkqefx Akfja Application Types Cutting

Condition: excellent (used), Plasma cutter SAF Nerta Zip 20-40 A Type 0408_2240 380 Volt 10/18 A 220 Volt 16/30 A Cutting current 20/40 A Transport dimension : Length 700 mm width 430 mm height 970 mm Weight 90 kg Nodsvdqkvspfx Akfjla

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, working width: 3,500 mm, working length: 8,000 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Working length: 8,000 mm Working width: 3,500 mm Nlsdpoyv Awkofx Akfsa MACHINE DETAILS Power: 300 A Plasma source: Nertajet EQUIPMENT 1 torch head 1 plasma head 1 oxy-fuel head

Condition: used, Year of construction: 2018, functionality: fully functional, type of input current: AC, working range: 3,000 mm, sheet thickness (max.): 30 mm, sheet thickness steel (max.): 30 mm, overall weight: 1,500 kg, input voltage: 380 V, We hereby offer for sale a used plasma cutting machine Model: UP-1530 Brand: Plasmabron Huayuan 200 Amp, with Hypertherm torch The Z-axis is equipped with height control Cutting thickness up to a maximum of 30 mm steel. (Equivalent to Max Pro 200) Control: Starfire F2300 Controller. Guidance: HIWIN linear guideways. The machine has been dismantled and is in working condition. Nlodpfjyv H Erjx Akfoa

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, type of input current: AC, input voltage: 400 V, hose package length: 22,800 mm, ground cable length: 5,000 mm, sheet thickness steel (max.): 50 mm, air pressure: 5.9 bar, Next-generation air plasma system that significantly simplifies system operation for cutting and gouging up to 32 mm, featuring automated process setup via advanced RFID-enabled SmartSYNC torch and a revolutionary one-piece consumable that provides trackable usage data. Technical data: Cutting performance: Recommended cutting capacity: 32 mm – 500 mm/min Maximum cutting capacity: 38 mm – 250 mm/min Severance capacity: 50 mm – 125 mm/min Nsdpjykp R Sofx Akfela Pierce capacity: 22 mm Typical gouging: Metal removal rate: 8.6 kg per hour Gouge profile: 6.6 mm D x 6.0 mm W Scope of delivery: Power cable, H105 handheld torch 22.8 m (75°), work lead with clamp, instruction manual

Condition: good (used), Year of construction: 2010, Offer 25375 Technical Data: - Working area / cutting length with approx. 5 m rails: approx. 3000 mm - Working area / cutting width: approx. 1500 mm - Controller: BACH - Track gauge: approx. 1900 mm - 1 plasma torch with height adjustment - Plasma source: KJELLBERG Hi FOCUS 160 i - Cutting current at 100% duty cycle: 10 - 160 A - Cutting range (steel): approx. 5 - 50 mm - Cutting range (aluminium): approx. 5 - 35 mm - Cutting range (stainless steel): approx. 5 - 30 mm - Connection: 400 V / 35 kVA Nlodpfexnivzex Akfea - Extraction table with extraction unit, make: TEKA, type: Filtercube 4 H, year 2010 - Weight: approx. 4 t - Space requirement for system: approx. L 7.5 x H 1.5 x D 2.4 m - Space requirement for extraction unit: approx. L 1.5 x H 3.5 x D 1.5 m