Used Sliding Bed Lathe for sale (14,732)

Condition: used, Year of construction: 1971, swing diameter 0520 mm turning diameter over bed slide 400 mm turning dia. in gap 1000 mm Iedpfxoy Nd S Ae Ahnjig turning length 1250 mm turning speed range - spindle 11,2 - 1120 U/min total power requirement 7 kW weight of the machine ca. 3,8 t dimensions of the machine ca. 2,7 x 1,7 x 1,7 m Machine has a 4 position toolholder with quick change device and DRO.

Condition: used, Year of construction: 1977, functionality: fully functional, Headstock and faceplate lathe with sliding bed This machine can be used for normal turning operations, as well as with the bed shifted by approximately 500 mm, for large diameters up to 2000 mm. This makes the machine very space-saving. It is a special lathe for both normal and large workpieces, thanks to this sliding bed option. Manufacturer: Ravensburg Model: 1500 x 2000 mm Year of manufacture: 1977 Faceplate diameter: 1500 mm Center height in the crank: 1000 mm with the bed shifted Turning diameter in the crank: 2000 mm Iiodpfx Ahszxgr Uonog Turning length: 2000 mm Simple steel support: 90 mm high Top slide with automatic feed: 500 mm Top slide, transverse: 400 mm Slide, transverse: 700 mm 3-way bed, width: 240; 150, 150 mm L x W x H: 6000 x 2300 x 2300 mm

Condition: excellent (used), Year of construction: 1997, turning diameter over bed slide: 1,240 mm, turning diameter over top slide: 980 mm, turning length: 3,000 mm, DBC Turning Length: 3000mm Swing over bed Ø: 1240mm Swing over cross slide Ø:980mm Swing in the gap Ø: 1980mm Gap length: 1500mm Spindle bore: 130mm Spindle power: 30kW Bed width: 500mm Stroke pinole: 300mm Spindle taper: 5Mk Speeds / ranges: 800Rpm Feed rate X-Axis: 8000mm/min. Feed rate Z-Axis: 8000mm/min. Workpiece load: 4000 Length: 7000mm Width: 2200mm Height: 2300mm Iijdpfx Ahjx Di Rqensg Weight: 12400kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 1996, spindle bore: 160 mm, Swing over bed Ø 1040 mm Swing over cross slide Ø 710 mm Swing in the gap Ø 1580 mm DBC Turning Length 3000/4500 mm Gap length 1500 mm Spindle bore 160 mm Spindle power 40 kW Bed width 800 mm Spindle taper 6 Mk Workpiece weight Iiodpfsxtbf Eex Ahneg 3500 Speeds / ranges 800 Rpm Feed rate X-Axis 10000 mm/min. Feed rate Z-Axis 10000 mm/min. Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Iiedpfx Aox Tgr Tohnjg Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1958, condition: used, machine/vehicle number: 58/803 0021, height of centers: ueber Oberbett 300 mm center distance: 1500 mm max. circulation-Ø over bed: ueber Oberbett 640 mm spindle boring: 67 mm spindle retainer: Gr. 8 Iodpfxo Uin Uo Ahneig retainer taper tailstock: 5 MK spindle speed: 18 - 900 rpm forwarding feed: laengs/plan 0,063-2/0,032-1 mm/U thread pitch: 0,5 - 14 mm electrical connection: 380 V, ca. 7,5 kW space needed: 1550 x 3100 x 1250 mm weight: ca. 3500 kg

Condition: excellent (used), Year of construction: 1998, functionality: fully functional, Swing over bed 1,300mm, over cross slide 1.000mm, swing in gap 2,100mm, center distansen 1,500mm, 2,350mm with open bed. Spindle bore 128mm, 450 Rpm, 50 Kw, Chuck 800mm, 4-jaw plate 900mm. Fagor CNC, weight ca 12.000kg Ijdjxqp I Njpfx Ahnoig

Condition: new, Year of construction: 2025, turning diameter over cross slide: 250 mm, turning length: 730 mm, turning diameter: 500 mm, spindle speed (max.): 1,800 rpm, CNC lathe machine CK 6150 with flat bed We offer a new CNC lathe machine model CK6150. We use this machine in our production and you can see it in operation before ordering. The CK 6150 lathe has a flat bed and hardening guides, which ensures a long period of operation of the equipment. The machine is equipped with a CNC system, the GSK CNC system is installed as standard. Optionally, the machine can be equipped with a Fanuc or Siemens CNC system. The machine can have a tool holder for 4-6 or 8 tools, depending on the customer's wishes. It is possible to install a hydraulic chuck on the machine, which will greatly simplify the process of installing parts on it and a hydraulic tailstock. The CK 6150 lathe can be equipped with additional supporting frame for more accurate manufacturing of long parts. Technical specifications: Model CK 6150 x 1000 Maximum workpiece diameter over bed 500 mm Maximum workpiece diameter over support 250 mm Maximum workpiece length 1000 mm Maximum turning length 730 mm Spindle bore diameter 82 mm Spindle speed 150-1800 rpm Engine power 7.5 kW Mechanical chuck (hydraulic optional) Chuck size 250 mm. 4-position tool holder (6 or 8 optional) Iisdpfx Ajxdmgvehnjg Maximum tool size for tool holder 25x25 mm Machine weight 2700 kg Machine dimensions 2650×1700×1820 mm We can also supply lathes CK 6140, CK 6150 and CK 6160 with other dimensions of the working part: CK 6140 dimensions of the working part 550/750 mm CK 6150 dimensions of the working part 1000/1500/2000 mm CK 6160 dimensions of the working part 1000/1500/2000 mm CK 6152E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6185E dimensions of the working part 1000/1500/2000/3000/4000 mm CK 61100E dimensions of the working part 1000/1500/2000/3000 mm CK 61125E dimensions of the working part 1000/1500/2000/3000 mm

Condition: used, Year of construction: 2005, Technical details: spindle passage: 54 mm z-axis: 900 mm turning length: 900 mm swing diameter: 560 mm facing movement (x-axis): 290 mm control: Simens Sinumerik 840D sl spindle turning speed - continuous: 0 - 6000 U/min diameter of main spindle: 120 mm max. torque on the spindle: 190 Nm tool turret: Typ Sauter number of tool tapers: 12 operating pressure: 5 - 6 bar quill stroke: 130 mm diameter of quill: 110 mm rapid traverse: 40 - 50 m/min total power requirement: 37,5 KW weight of the machine ca.: 8,0 t dimension machine approx.LxWxH: 4,8 x 2,4 x 2,3 m Iisdpfx Ahoy Ttyqonjg • Modular machine design for efficient 2-axis and 4-axis shaft machining as well as chucking part machining • Equipped with pick-up spindle • High basic accuracy and thermal stability as prerequisites for hard turning and precision machining • Prepared for automatic loading and unloading via gantry loader or integrated loading system • Separable machining area for simultaneous two-stage machining on the left and right main spindles • Lowerable tailstock can be combined with a counter spindle • Supports in-process and post-process measurement strategies *

Condition: as good as new (ex-display), Year of construction: 2024, operating hours: 10 h, functionality: fully functional, Controller SIEMENS 828D with Shopturn and 17 inch Touch screen Swing dia 550 mm Turning length 428 mm Max. turning dia 300 mm Spindle bore 62 mm Max bar dia 51 mm Spindle face A2-6 Spindle speed 35 - 5000 rpm motorspindel Travel X axis 210 mm Travel Z axis 561 mm Turret 12-fold (all stations driven) Turret interlock hydraulic Turret drive servo Tool change time 0,2 sec. Tool section 25x 25 mm Max speed of life tools 5000 rpm. Max power of live tools 5 kW Max milling capacity (shaft mill) 16 mm Max milling capacity (milling head) 50 mm Max drilling capacity D16 mm Max tapping capacity M16x2 Rapid speed Z axis 30 m/min Rapid speed X axis 30 m/min Position accuracy 0,008 mm Repeat accuracy 0,003 mm Tailstock Pinole conus MT4 Travel of tailstock body 565 mm Hydraulic tank capacity 20 L. Power of hydraulic pump 1,5 kW Hydraulic power 3,5 - 6 Mpa Isdpfx Ahewbu T Usnsig Volumen of lubrication 2 L Power of lubrication pump 25 W Coolant tank volume 130 L Power of coolant pump 25 W Motor power cont. 11 kW 400 Volt 50Hz Motor power short time (30 min) 15 kW 400 Volt 50 Hz Weight 4000 kg Dimensions LxWxH = 2600 x 1685 x 1768 mm Accessories Coolant unit, Turret for 12 driven tools, 200 mm hydr. chuck, Linear guides and ball screws THK/Japan, SHOP TURN, Spindle cooler, Chip conveyor, Tool presetter, automatic tool length compensation, barfeeder interface, air blowing for chuck and turret, high pressure coolant, oil selector.

Condition: used, Colchester Triumph 2000 Gap Bed Centre Lathe with Acu-rite III 2 Axis DRO, Swing Over Bed 400mm Diameter, Distance between Centres 1300mm, 250mm 3 Jaw Chuck, Spindle 25 - 2000rpm, 3 Position QCTP. S/No. 6/0044/28919 Location: These lots are located in Andover, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. Lot 12 of Auction 3500 - Ending Wednesday 30th September 2026 at 3pm (UK Time) Iisdsz Aqwcjpfx Ahneg

Condition: reconditioned (used), Colchester Triumph 2000 x 50” Gap Bed Centre Lathe Height of Centres 190mm Iiodpfxezzxxfo Ahnog Max’ Distance Between Centres 1250mm Max’ Swing over Bed 390mm Max’ Swing over Cross Slide 240mm Max’ Swing in Gap 580mm Spindle Bore 54mm Spindle Nose D16 Camlock Spindle Taper in Bush No.4 Morse Spindle Speeds 25 - 2000 rev/min Tailstock No.4 Morse 3 Phase Electrics 7.5hp Motor Supplied with: 3 Jaw Chuck Digital Readout Quick Change Tool Post This machine is an ex-university machine and is in excellent condition overall.

Condition: used, Hardinge Talent Slant Bed CNC Lathe Model TI. S/No. 4500117 with Fanuc OT-B CNC Control, 10 Position Tool Turret, Tailstock, Hardinge Collet Chuck and Collets, Acrovu Feedmaster CNC Barfeed 5m Long, Kitagawa B-205 Powered Chuck Isdpfx Ahozy Rafsnsig Location: These lots are located in Andover, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser.

Condition: used, XYZ 2400 Gap Bed Centre Lathe with Acu-rite 2 Axis DRO, 315mm 3 Jaw Chuck, Swing Over Bed 660mm Diameter, Distance between Centres 2400mm, Spindle Speeds 30 - 1500rpm, 2 Position QCTP, 710mm Diameter Face Plate, Steady Location: These lots are located in Andover, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. Iodpfx Ahezy N Rcsnjig

Condition: used, Year of construction: 2007, machine/vehicle number: 511979, Turning length: approx. 400 mm, bar passage: 60 mm, Y-axis, counter spindle, 2x 14-station tool turret, cross slide X/Y/Z, B-axis slide control INDEX C 200-4 D, workpiece removal, conveyor belt, chip conveyor, manufacturer: KNOLL, bar loader MBL 65/3700, machine requires repair, gear pump defective, repair costs according to quotation: approx. €6,000.00 net, drilling emulsion/lubricants must be professionally extracted and disposed of by the customer. Isdpfezqy Uyox Ahnjig

Condition: used, Year of construction: 2007, machine/vehicle number: 402235, Spindle bore: 36 mm, maximum spindle speed: 7,000 rpm. C-axis, 1 turret, X/Z-axis, 7-station + synchronized spindle, driven tools, 1 tool turret, X/Z-axis, 6-station, driven tools, control system: INDEX C 200-4 D, back-side machining, workpiece removal, conveyor belt, chip conveyor, bar loader MBL 52/3200. Drilling emulsion/lubricants must be professionally extracted and disposed of by the customer. Iiedpfxszqy U Tj Ahnjg

Year of construction: 2018, condition: used, machine/vehicle number: 01160, Max. machining diameter: 42 mm, max. turning length: 300 mm, control system: FANUC Series 32I-Model B, filter unit, 1 left-hand bar feeder BARLOAD Vito, year of manufacture: 2018, serial no.: 22181574, weight: 980 kg, right-hand conveyor belt, chip conveyor, oil cooler HABOR, extinguishing system, without tools. Iiodjzqy S Eopfx Ahnog

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: XD-16III-CP-0073-H, spindle bore: 18 mm, spindle speed (min.): 10 rpm, spindle speed (max.): 1,500 rpm, type of input current: three-phase, overall weight: 2,200 kg, rotational speed (min.): 10 rpm, Equipment: documentation/manual, Hanwha XD16 III Few operating hours Barloader BMG-20 Chip conveyor with trolley and collector Fanuc control Iiodpfxjzxhwro Ahnsg Bar diameter modified to Ø18mm

Condition: good (used), Year of construction: 2004, functionality: fully functional, Fanuc control system, 32 mm spindle bore, Iiodpfx Aozqbn Ujhneg Turret with driven tools, Counter spindle, Tool magazine, High-pressure pump.

Condition: excellent (used), Turning diameter max. 20 mm Ijdpfx Asmmdacshnsig Turning lenght max. 320 mm Spindle bore 24 mm Spindle speeds 200-10'000 rpm Turret with 10 pos., all of them are driven Barloader LNS Misc. accessories MARCELS MASCHINEN AG

Condition: excellent (used), SOMAB TRANSMAB 200 is a CNC turning lathe with slant bed, engineered for precision, high accuracy and reliability. Swing over bed 260 mm, spindle bore 35 mm; travels Z 300 mm, X 125 mm. Turret DUPLOMATIC with 8 positions, 8 fixed tools, 16 mm tool shank, inner cone Ø20 mm. Stepless spindle 200–5000 rpm, spindle motor 4 kW, spindle taper A2-4", tailstock Morse 3 with 80 mm stroke and 52 mm diameter, pressure 1200 N; voltage 3x400 V 50 Hz; machine weight ~2500 kg; dimensions L1900×W1400×H1980 mm. Equipment: collet device and set (F38), lamp, tool cabinet, RS232 interface, foot pedal, set of toolholders. Delivers tight tolerances; typical applications: automotive, aerospace, medical, machine tools and watchmaking. Iedpozqbmwofx Ahnoig

Year of construction: 2013, condition: ready for operation (used), A CNC slant bed lathe Focus is offered. Swing diameter over bed: 600mm, max. turning diameter: 330mm, max. turning length: 669mm, spindle bore: 88mm, spindle speed: 3400rpm, travel X/Z: 260mm/762mm, rapid traverse X-axis: 20m/min, rapid traverse Z-axis: 24m/min, tool stations: 12, tool holder: VDI40, quill diameter: 85mm, tailstock taper: MK4, controls: Siemens. Weight: approx. 5700kg, machine dimensions: X/Y/Z: approx. 3600mm/1800mm/1800mm. Inspection possible by appointment. Iiedpfx Aszfaafohneg

Year of construction: 1984, condition: ready for operation (used), Control system: Philips B2T, machine currently not operational, partially dismantled, the fan of the main spindle motor has been completely renewed, the main drive and the mechanical assemblies (headstock, turret, ball screw) are intact, the Z-axis motor is defective and has already been professionally removed, the hydraulic clamping cylinder requires repair or must be replaced. An on-site inspection is possible. Ijdpfx Ajy Uyf Nehnoig

Year of construction: 1985, condition: ready for operation (used), Voltage: 380V, current consumption: 125/118A, control system: Philips B2T 6, equipment: hydraulically actuated turret vorhanden, enclosed working area with slant bed geometry, hydraulic clamping system, piping, condition: fully functional, very good mechanical condition, visually well maintained, partially overhauled, tool turret: angular position encoder completely renewed, turret indexes absolutely faultlessly and precisely according to the data sheet, CNC control system: power supply professionally overhauled, main spindle drive: power section/drive completely overhauled, with power chuck and base jaws. An on-site inspection is possible. Iiedpfx Ahey U Nqnsnjg

Condition: good (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: XD20BB0393, turning length: 210 mm, spindle speed (max.): 10,000 rpm, turning diameter: 20 mm, equipped with Iemca Boss 332E-r/32 barfeed new in 2008 with 12 mm guide channels - chip conveyor - Fanuc 18i-TB Control Iijdpfx Asr Arwushneg