Used Thread Wirling for sale (2,398)

Condition: used, GRIESER Type: GFD 11 LST Product: Grieser Laboratory Stand Dissolver Intended Use: Redpfx Aszdtfleiroch The machine is used for mixing powdery solids, liquids, and pastes, as well as for incorporating fillers. The viscosity range can range from thin to pasty. Machine Design: The laboratory stand dissolver consists essentially of the machine stand, the lifting device, the drive for the mixing tool, the telescopic hood with spring pressure, the collet chuck, and the control cabinet (non-Ex) with control and compact controller. In the working position, the container (customer-supplied) and the telescopic hood form a closed mixing chamber. A hose connection is provided on the hood, which serves according to the intended use. The drive of the mixing tool is equipped with a speed control via a frequency inverter. The arrangement, power, and speeds of the motors can be found in the attached project drawing. The speed of the mixing tool, the mixing time/remaining mixing time, mixing sequences, and other functions can be displayed on the display of the compact controller. Operation Switching on and off is done via corresponding buttons in the control cabinet. Lifting the mixing tool drive Lifting is carried out by switching on the lifting motor. This runs only as long as the push buttons (two-hand safety circuit UP-UP) are pressed. After releasing the buttons, the arm remains in any desired position. Lowering the mixing tool drive To lower the arm, the corresponding buttons (two-hand safety circuit DOWN-DOWN) on the control panel are pressed. Mixing tool change The mixing tool shaft is provided with an M8 connection thread. Depending on the requirement, the mixing tool (stirring blade, customer-supplied) can be unscrewed and replaced. Technical data: Machine type: GFD 11 LST Year of construction: 2017 Operating voltage: 400 V Frequency: 50 Hz Control voltage: 24 V DC Mixing tool speed: 25 – 500 min-1 via frequency inverter Ambient temperature: +5°C to +40°C Protection class: IP 54 Container: 1.18 liters, D=100, H=150 (75) customer-supplied Mixing tool: Stirring blade, customer-supplied Control panel / display The machine is operated primarily via the compact PLC controller "Vision 560-T25B". Safety-relevant functions such as disconnection from the mains via the main switch, shutdown in case of danger by pressing the emergency stop button, and the two-hand operation for opening or closing the mixing chamber are excluded. The control panel consists of an illuminated LCD display and film-covered tactile buttons. The buttons marked with a letter have fixed functions assigned to them. These can be activated at any time, independently of the menu. As soon as a function has been activated, the corresponding status appears in the upper right area of the screen in the "Operating Display" menu. The individual menu screens can be switched through using the up and down buttons. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and information are subject to change!) We will be happy to answer any further questions you may have by telephone.

Year of construction: 2025, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 54942, No minimum price – guaranteed sale to the highest bidder! EXW – Dismantling and loading must be organized by the buyer! TECHNICAL DETAILS Nominal test force: 50 kN Test stroke: < 1,400 mm Usable distance between pressure plates: approx. 800 mm Test area width: 500 mm Test speed: continuously variable 0.001–1,200 mm/min Resolution of displacement measurement: ≤ 0.001 mm Redpfsz Tf D Rjx Airech Diameter of pressure plates: 246 mm Centering bore: 40 mm Thread: M12 Hardness: ≥ 56 HRC Design: Steel, hardened, rotatable at the top and bottom, lockable at 0° Measuring range of the enveloping circle: 30–250 mm Design: Probe with bearing rollers Measurement: Recording under load MACHINE DETAILS Control system: Control system with control computer Test program: Enveloping circle measurement Network: Fast Ethernet, 100 Mbit/s between the control computer and the separately required operating PC Software delivery: USB stick with installation software Documentation: Version and license status not documented separately Last calibration: 08/04/2025 Dimensions & Weight Machine dimensions: approx. 750 × 900 × 1,950 mm Base frame dimensions: approx. 730 × 900 × 700 mm Control cabinet with control computer dimensions: approx. 600 × 600 × 1,900 mm Machine weight: approx. 490 kg Base frame weight: approx. 50 kg Voltage supply: 3 × 400 V AC, 50 Hz, N + PE Type plate power: 3,000 W Connected power: approx. 3 kVA EQUIPMENT Base frame Control cabinet with control computer Rotatable pressure plates Enveloping circle measuring device with probes and bearing rollers USB stick with installation software Compressed air connection: Pneumatic connection with shut-off valve Note: The functionality has been tested and confirmed. However, an unresolved error message on the drive prevents further use. The machine is in like-new condition visually. The operating PC is not included in the offer.

Year of construction: 2011, operating hours: 10,500 h, condition: used, machine/vehicle number: ISP17, Used Inspector KRONES Linatronic K735 year 2011 The Used Inspector KRONES Linatronic K735 year 2011 offers a proven and efficient solution for quality control in high-performance bottling lines. The German manufacturer KRONES, a global leader in beverage industry automation, built this model with reliability, precision, and modular construction in mind. As a result, this inspector fits seamlessly into industrial environments that demand high accuracy and operational consistency. Electrical characteristics and technical configuration of the Used Inspector KRONES The Used Inspector KRONES Linatronic K735 year 2011 runs on a three-phase power supply at 400/230 volts, with a 50 Hz frequency and a 13-ampere current draw. Consequently, it aligns with European industrial standards and supports stable operation under demanding conditions. Furthermore, the electrical system includes integrated safety devices that protect the components from overload or malfunction. In addition, the compact and durable enclosure facilitates easy integration into existing production layouts. Year of production and machine hours KRONES produced this unit in 2011. Since then, the machine has logged 10,500 operating hours, which reflects moderate usage for equipment designed for industrial use. Compared to other models with similar functionality, this unit maintains good performance standards. Moreover, the machine structure shows minimal wear, confirming its careful maintenance. Therefore, technicians can expect reliable functionality without immediate need for major refurbishment. The machine is currently operational, specifically until Easter. Then it will be dismantled.  Rcodpfx Ae Adyv Usirjh Supported inspection types The Used Inspector KRONES Linatronic K735 year 2011 is equipped with a comprehensive range of inspection functions to ensure the quality and integrity of each bottle. -The system performs bottom inspection to detect chips, cracks, or foreign objects at the base. -The sidewall (walls) inspection uses a rotating mirror and cameras to identify defects such as scratches, cracks, or dirt on the entire lateral surface. -The neck finish and thread inspection ensures that bottle openings are free from damage or deformation that could compromise sealing or capping. -Scuffing inspection checks for surface abrasions that indicate excessive wear. In addition, the machine employs infrared (IR) and high-frequency (HF) technology to detect residual liquid, ensuring the bottles are dry and ready for fill...

Condition: used, Year of construction: 1999, Machine number: 9114108 Weight (approx.): 150 kg Motor power: 0.71 / 1.26 kW Overhang – stand to drilling center: 600 mm Max. material height: 200 mm Table width: 1000 mm Number of drilling spindles: 4 Rcedpfx Aiszd Hnterjh Drill chuck: Screw-in thread Drilling depth limitation: Yes Drilling stroke: 70 mm Speeds: 1400 / 2800 rpm Workpiece clamp: Yes Drilling feed: Hand lever Working height or feed table height: 890 mm, with lighting Storage location: Nattheim

Condition: used, max. veneer thickness: 2.0 mm Rcodpfxoxgqmxe Airsh min. veneer thickness: 0.4 mm Joining material: glue thread with hot air heating Compressed air required: yes Disc: Yes, for transporting the veneer over the veneer table Control via foot pedal Machine type: floor model Feed speed: 7 m/min Stand extension: 900 mm Weight approx.: 185 kg Dimensions: 1400 x 500 x 1680 mm Storage location: Nattheim

Condition: new, functionality: fully functional, Year of construction: 2025, laser power: 60 W, laser wavelength: 1,070 nm, type of cooling: air, warranty duration: 12 months, shaft length: 1,070 mm, Equipment: cabin, Laser engraving machine with 60-watt laser power (new) - 60-watt MOPA laser (enables color laser engraving on stainless steel) - incl. 4th axis (rotary unit) - incl. Windows 10 Pro 64-bit PC system - incl. 22" monitor - everything fully installed and calibrated - Engraving software in German - very easy to operate - switch on and start - Fiber laser source with 60 watts for high-contrast and fast markings with extremely high resolution (see images) Rsdpfxefkgq Nj Airsch - Deep engraving up to 4mm possible (also in hardened steel) - Wobble function, e.g., for cleaning metal components - for engraving on many metals (stainless steel, brass, aluminum, etc.) and many plastics - heavy-duty industrial quality - Complete system / ready for immediate use - Working area approx. 500 x 600 x 600mm (l x w x h) - Clamping surface with fastening threads in a 50mm grid - LED work area lighting - 50mm pipe connection for fume extraction - Engraving area approx. 180 x 180mm - expandable to approx. 300 x 300mm - incl. foot switch to start the engraving process Please also note our attractive leasing/hire-purchase offers. Sales are exclusively to commercial businesses. Delivery / Consulting / Sales only in Germany / Austria / Switzerland Machine dimensions approx.: Width: 800mm Height: 1800mm Depth: 1000mm Weight: approx. 150kg

Condition: used, CITIZEN CINCOM R 07 VI is a high-precision CNC automatic lathe (Swiss-type) delivering strong accuracy and reliability. Capacities: 6 axes, 2 spindles; max turning Ø 7 mm, max length 40 mm, spindle bore 12 mm; threading up to Ø4 M, max tapping length 40 mm. Specs: spindle 0–16,000 rpm, 1.1 kW; back spindle up to 10,000 rpm, 0.5 kW; C-axis resolution 1°; supply 3x400 V 50 Hz, total power 4 kVA; weight ~950 kg; footprint 1465×560×1410 mm. Accessories: parts catcher, lamp, bar feeder LNS TRYTON 107, central lubrication, status light. Built to achieve tight tolerances; typical applications include automotive, watchmaking, medical, aerospace, and machine-tool components Rodpfx Aisyxnutsrjch

Condition: used, CITIZEN CINCOM R 04 VI is a CNC automatic lathe / Swiss-type lathe designed for high precision, accuracy and reliability. It features 6 axes and 2 spindles, max. turning diameter 4 mm, max. turning length 40 mm, internal spindle diameter 9 mm, max. threading diameter 3 M. Main specs: up to 20000 t/min, spindle power 0.5/0.75 kW; tool-holder count 3 with 15 stations; turning tools 5, drilling tools 4, transverse tools 2; tool shank 8 mm; counter-operation 4 tools. Voltage 50 Hz 3x400 V; machine weight ≈850 kg; dimensions L1485×W560×H1410 mm. Accessories: LNS TRYTON 107 Hybrid bar feeder, parts catcher, coolant system, lamp. Ensures tight tolerances; suited to watchmaking, medical, automotive, aerospace and precision components. Rjdpfxezv I D Hs Airsch

Condition: new, GMN TSE 240 cg - SP: 3000-3600-4000-5000 RPM / 37 grinding spindle, shaft diameter: 130mm, front overhang at the thread: 102mm, including test report and installation instructions, new condition: €25,000, unused, 100% functional, scope of supply as shown in the photos. Rcsdpfx Aoi D U Troirsh ATTENTION: Please request the costs for packaging and shipping separately!

Condition: used, Year of construction: 2021, Drilling capacity in St 60 55 mm threading in St 60 M 30 M 36 Short spindle MK 4 spindle stroke 140 mm throat 300 mm column diameter 145 mm Machine table - usable table surface 615x430 mm T-Slots Amount - Width - Distance 2x14x224 mm distance spindle - column min./max. 150/735 mm feed 0,1 + 0,3 mm/U 0 stufenlos Spindle Speed 70-2.400 U/min. engine 3,0 kW machine weight ab. 380 kg Standard equipment: - 7" TFT LCD display with touch function: * Manual input of spindle speed set value * Actual speed display * Integrated drilling depth display with touch zero point transfer * Virtual drilling depth scale in the display * Machine status indicators and warnings on the display * Service information * Selectable operating language: DE/EN/FR/ES/IT/NL/RU - Thread cutting device, for thread cutting with stop, max. 6 threads/min (thread cutting capacity depending on spindle speed), thread depth adjustable via depth stop and on the TFT LCD display (4 tools) - Infinitely variable speed adjustment via adjustment lever - Spindle protection with electrical fuse - Three separate buttons for clockwise rotation - anticlockwise rotation - stop - Mushroom pushbutton (latching) for EMERGENCY STOP - Main switch, lockable - Clockwise and counter-clockwise rotation via contactor control - Control voltage 24 V, protection class IP 54 - Paint finish: DD textured paint signal white RAL 9003, PANTONE 4545c, black Item 20.5 Foot switch in addition to the thread cutting device, for switching the direction of spindle rotation in the process. direction of rotation during the process Item 25. Coolant unit B, consisting of: separate container (33 l), pump with motor protection switch, complete armature motor protection switch, complete fitting Item 37.5 Technology calculator in the display The technology calculator guides you through the cutting task Determination of the cutting data using the following parameters: - Manufacturing process - Tool diameter - Cutting speed - Material table - Transfer function of the spindle speed as set value Rcsdpjz I Ub Hefx Airoh

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 615, overall weight: 8,700 kg, The Mori Seiki SL-303 BMC/1500 is a robust, high-precision 3-axis CNC slant-bed turning and milling center. The model designation indicates a system with powered tools (BMC), a C-axis, milling capability (MC), and an extended center distance of 1500 mm for machining long workpieces (e.g., shafts). Equipment: -Single spindle, three-jaw chuck, automatic tailstock SMW Autoblock, 12-position tool turret, automatic steady rest, chip conveyor Control: -MSG-501 (SL303-615) Rsdoz N Dkbepfx Airjch Key features & benefits: -Complete machining (multi-process): The use of powered tools and C-axis control allows milling, drilling, and threading operations to be performed directly after turning without re-clamping. -High rigidity: The massive cast iron slant bed effectively dampens vibrations, resulting in excellent surface finishes and a long tool life. -Thermal stability: Comprehensive cooling and oil circuits around the spindle minimize thermal expansion during long and heavy roughing operations. Accessories: -Work bench with partition (1 door, 3 drawers) Contents: hand tools -Telescopic drawer cabinet (7 drawers), side shelf Contents: various turning tools and tool holders Attractive offer – flexible and worry-free We offer not only a high-quality product, but also tailored financing options that adapt to your needs. Whether it’s a down payment, installment payments, or individual financing models – together we will find the right solution. If desired, we will also take over the complete transport organization. From planning to reliable delivery, we ensure a smooth and timely process so you don’t have to worry about anything. 📞 Please contact us for more information or a non-binding offer. We will provide you with personal and expert advice. Subject to prior sale, changes and errors!

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, Weiler Praktikant 160 B, lathe with guide and draw spindle, year of manufacture 2000, with 3-axis digital display K&C, NEW, CE marking!! Technical data: >> Year of manufacture 2000, machine no. 4651 >> Center height 160 mm >> Distance between centers 650 mm >> Spindle speeds: from 24 to 2500 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.02 to 0.63 mm/rev >> Possible threads: metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight approx. 680 kg >> Spindle brake can be switched on >> Length 1.6 m, height 1.25 m, depth 0.7 m Rcodpfx Ao Afxq Seireh Accessories and equipment: >> 3-axis digital display from K&C, new, 12 months manufacturer's warranty, with operating manual Functions: switching mm/inch, coordinate selection ABS/INC, halving the display value, reference mark, tool programming 200 pieces, taper calculation, radius/diameter, quick zeroing, switching the counting direction >> Quick-change tool holder, collets from 2 to 28 mm, increasing in 1 mm steps >> 3-jaw chuck 160 mm Röhm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> Electric chuck guard >> Bed stop, drill chuck >> Back wall >> Machine feet >> Coolant system >> Operating manual, parts list (PDF) About the machine: Offered is a Weiler Praktikant 160 B lathe with guide and draw spindle, year of manufacture 2000, in very good condition. The machine is fully functional and has CE marking. All slides run very smoothly and evenly. The Weiler comes from a training workshop. Even at high speeds, the Weiler runs smoothly. This newer generation of Weiler lathes is very user-friendly and allows for the production of surfaces that appear to be ground. Take the opportunity to inspect this machine on site and under power to convince yourself of its condition.

Condition: new, functionality: fully functional, Year of construction: 2026, machine/vehicle number: HAW1700-EV-Funk, rope length: 30,000 mm, rope speed: 47,000 mm/min, Hydraulic winch for wood splitters, cranes, mini excavators, tractors, agricultural vehicles, viticulture, horticulture, and many other applications. The hydraulic attachment winch simplifies many tasks: - Pulling and positioning firewood to the wood splitter - Pulling logs onto trailers - Removing tree stumps and roots - As an attachment winch on forestry cranes and small excavators - As a winch for small tractors and narrow-gauge tractors A robust steel construction with 3-sided mounting options (left, right, rear) and 12 threaded holes offers many possibilities for attaching the winch (threads are cut and painted. They need to be re-cut with a thread tap before use due to the rust protection). A 20 m long and 6 mm thick steel cable is mounted. A large cable pulley ensures a long service life for the steel cable. We mount hydraulic motors from 50 to 630 cc (standard = 400 cc), depending on the speed and pulling force required. Maximum working pressure: 225 bar peak Continuous operating pressure: 175 bar Displacement: 400 cc Torque at 225 bar: 870 Nm peak Torque in continuous operation: 380 Nm Maximum pulling force: 1700 kg Weight: 49 kg Cable speed: 47 m/min at 60 L/min hydraulic oil Color: red Dimensions: Length: 500 mm Length with swivel: 570 mm Front width: 120 mm Rear width: 180 mm Bearing width: + 30 mm Motor width: + 200 mm Height: 250 mm Rodpfxedf Ufpj Airsch The winch is available for mounting or welding. This version includes an electric hydraulic valve, remote control, and hoses to the motor. Article number: HAW1700-EV-Funk

Condition: new, Year of construction: 2026, Hydraulic winch HAW1700 with electric valve incl. manual operation and radio remote control for mounting on wood splitters, cranes, mini excavators, tractors, forklifts, mowing tracked vehicles, and telescopic loaders, for use in viticulture and horticulture, agriculture, construction, and forestry, as well as many other applications. Equipped with an electric hydraulic valve and radio remote control. The hydraulic winch HAW1700 can simplify many tasks. Maximum rope capacity of 30 m with 6 mm wire rope. Standard equipment includes 20 m of 6 mm wire rope. ⦁ Pull and position firewood for the wood splitter ⦁ Pull logs onto a trailer ⦁ Pull out tree stumps and trees ⦁ As an auxiliary winch on skidders and small excavators ⦁ As a winch for small tractors and narrow-gauge tractors A robust steel construction with the possibility of mounting on both sides (bottom, rear, top) with M12 threads. This allows for flexible use of the winch. Large, double-bearing rope pulley for long wire rope life. The pulling force is 1700 kg as standard. The winch can be installed in various positions. An optional hydraulic brake is available. Depending on the required pulling speeds and forces, we can offer you different options. Please contact us, and we will be happy to advise you. ⦁ Maximum working pressure: 225 bar peak ⦁ Continuous operating pressure: 175 bar ⦁ Displacement: 400 ccm ⦁ Torque at 225 bar: 870 Nm peak ⦁ Torque in continuous operation: 380 Nm ⦁ Maximum pulling force: 1700 kg ⦁ Weight: 49 kg ⦁ Rope speed: 47 m/min at 60 l/min oil flow ⦁ Color: red ⦁ Including hoses from the valve to the motor Dimensions: ⦁ Length: 500 mm ⦁ Length with rope inlet: 570 mm ⦁ Front width: 120 mm ⦁ Rear width: 180 mm ⦁ Bearing width: +30 mm ⦁ Motor width: +200 mm ⦁ Height: 250 mm Included: Radio remote control for the winch. Redpfx Aofn Tvhoirech ⦁ Control range: up to 100 m ⦁ Temperature: -35 °C to +80 °C Protection class: IP65

Condition: new, functionality: fully functional, Year of construction: 2026, overall weight: 100 kg, total height: 1,000 mm, color: red, continuous operating pressure: 210 bar, spindle torque (max.): 1,800 Nm, Equipment: hydraulics, Cone splitter Excavator splitter Drill cone splitter Wood splitter KS5 Drill cone 200x400 - Made in Germany The powerful cone splitter for attachment to mini-excavators, excavators, wheel loaders, tractors, skidders and many other options. The drill cone can be exchanged for various tools such as a root cutter, auger, hummus sieve, concrete mixing drum, weed broom and many other attachments. The cone splitter consists of a very stable drive unit and the drill cone (splitting cone) The drill cone is completely hardened. It is not made of unhardened steel as is the case with many other manufacturers. It can be converted to other tools in a few simple steps. - Cone splitter - Root cutter - Earth auger - Weed brush - Sweeping broom - Rotary harrows NO CHINA GOODS ! WE PRODUCE IN GERMANY ! THE ideal multi-purpose tool for foresters, farmers, gardeners, do-it-yourselfers and professionals Redpfx Aeuph Uxoirsch Overall length 600 mm plus attachment and interchangeable system Universally applicable in construction, forestry, agriculture and horticulture For splitting heavy firewood or wood for wood chips For drilling holes in the ground, for stakes, plants and much more For removing rootstocks and tree stumps For cleaning trenches and paved areas For levelling garden areas and creating a fine soil structure You simply do the work from the excavator without any further assistance. A very solid and stable steel construction enables you to work hard and for a long time. In addition to the motor, the shaft is supported by 2 sturdy tapered roller bearings to protect against tension and pressure. The tapered roller bearings can be lubricated for a long service life. A powerful HMT 500 hydraulic motor with up to 1,800 Nm gives you the necessary torque for efficient work, from 25 l/min up to 125 l/min and 210 bar pressure Weight 70 kg included: - Drive unit with powerful HMT hydraulic motor, weight 70 kg - Drill cone with tip Ø 200 mm 270 mm/400 mm long, 6xM16 thread LK173 on the front side Total length 270 mm + drill cone tip 130 mm = 400 mm Diameter 200 mm Weight 30 kg Total weight 100 kg

Condition: not inspected (used), Year of construction: 2000, machine/vehicle number: 3244.00, total length: 2,700 mm, total width: 1,500 mm, total height: 2,000 mm, overall weight: 2,800 kg, DMT Kern CD 480 Lathe Technical specifications: Control system: Heidenhain Manual Plus 3110 Working area: Swinging diameter over bed: 475 mm Redpfx Aj Af U Icjirjch Swinging diameter over cross slide: 260 mm Cross slide travel: 260 mm Distance between centers: 1,000 mm Turning length: 880 mm Headstock: Spindle head DIN 55026: Size A6 Spindle diameter in the front bearing: 115 mm Spindle bore: 78 mm Standard chuck sizes: 200/250 mm Speed range (constant speed): 1–3,000 rpm Cross slide: Rapid traverse in X-axis: 0.001–1000 mm/rev Rapid traverse in Z-axis and threading: 0.001–2000 mm/rev Rapid traverse X/Z: 5/10 m/min Tailstock: Tailstock spindle diameter: 70 mm Tailstock spindle travel: 120 mm Tailstock spindle taper: MK 5 Scope of delivery: No further accessories Dimensions & weights: Overall dimensions L x W x H approx.: 2700 x 1500 x 2000 mm Weight approx.: 2800 kg If you have any questions or would like to arrange a viewing, please do not hesitate to contact us! Additional information: ►Upon request, we can offer transport to the desired location. ►The quoted price is net plus VAT. ►The goods are sold excluding any warranty. ►Technical data subject to change. ►Subject to prior sale. ❗The sale of the goods is exclusively to business customers❗

Condition: new, Description: hardened, galvanized Thread: R 1/4" Wrench size: 17 mm Overall length: approx. 19 mm Thread length: approx. 14 mm Rcedpfj Agcmmox Airjh Outer diameter: 13 mm

Condition: used, Year of construction: 1974, Technical details: turning diameter over bed: 500 mm turning diameter over support: 300 mm Rcsdsu Ix Dcepfx Aireh turning length: 2100 mm centre distance: 2000 mm spindle passage: Bohrung ca. Ø 60 mm range of revolution per miute: 35,5 - 1800 / 18 step U/min rapid motion - x-axis: Support 4,2 m/min tailstock quill taper MT: MK 5 tailstock quill adjustment: 180 mm control voltage: 220 V weight of the machine ca.: 3,25 t dimension machine approx.LxWxH: 3,5 x 1,2 x 1,6 m Thread cutting possible, e.g. metric thread, module thread and inch threadEilgang Quersupport Futterschutz 2x Späneauffangwanne Zubehör: (siehe vergleichbar auf Foto) 2x Lünette (1x geschlossen und 1x offen) Planscheibe 3-Backenfutter Backenpaare Flansch Spitzen div. Zahnräder *

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT21001013056, empty load weight: 3,290 kg, maximum load weight: 9,800 kg, overall weight: 10,500 kg, axle configuration: 2 axles, first registration: 05/2023, next inspection (TÜV): 03/2027, loading space length: 7,300 mm, loading space width: 2,480 mm, loading space height: 1,060 mm, total length: 9,690 mm, total width: 2,550 mm, total height: 3,580 mm, suspension: air, tire size: 235/75 R17,5", color: yellow, Please note: the images are archive photos. The vehicle may be in use! #Chassis centre-axle trailer - Fine-grain steel welded construction - Outer frame slightly inclined, new design with "Load-Lock-Profil" for lashing straps - 1 pair of geared landing legs at front, straight lower section, one-side operation on the right in direction of travel - Side door stays, steel underrun protection - Anti-spray mud flaps on last axle only, rear impact protection - Spare wheel carrier (1 wheel) with fastening kit - Platform height 1060 mm #Towing equipment - Drawbar with approved 40 mm drawbar eye, haulage version - Drawbar height mechanically adjustable via threaded spindle, below floor level, max. range 200 mm - Drawbar length mechanically adjustable approx. 1950 - 2300 mm, lockable approx. every 50 mm, set to approx. 2100 mm #Axles + suspension - BPW axles at manufacturer's choice, tapered roller bearings, S-cam brakes - Axles/running gear laser-aligned: reduces tyre wear and fuel consumption - Air suspension #Braking system - 2-line compressed-air braking system, colour-coded lines for easy servicing, spring-brake parking brake - Duomatic connection at front, with connecting line to the truck - EBS, electronic braking system with EBS connector at front - Please note: only to be towed by vehicles ensuring ABS effectiveness! - Raise/lower valve, vehicle stability system #Wheels and tyres - 235/75 R17.5, make at manufacturer's choice, steel rims, factory silver #Electrics - 24 V, multi-chamber lamps - Yellow LED side lighting, also coupled with indicators (flashing side marker lights) - 2 white front position lights, 2 white/red outline marker lights at rear - 1 x 15-pin connector at front - 2 additional LED work lights at rear, switched via reversing light #Floor - Film-faced plywood approx. 30 mm, for high point loads Rsdpfe Afwuzsx Airoch - Premium floor sealing, floor jointed all round - Platform length approx. 7,300 mm #Front wall / front corner posts - Through-loading via double-leaf front portal doors, each with 2 internal cam bar locks - Steel corner posts, release device for side tarpaulin - Bridge plate approx. 2,400 mm wide, divided once, approx. 350 mm long for resting on tail lift, capacity approx. 1,800 kg, incl. tail lift support - (Drawbar length then approx. 2300 mm; with 2000 mm tail lift, coupling set-back on truck min. 20 - max. 240 mm) #Side boards - 25 mm aluminium hollow profile, 400 mm high, drop-down and removable #Centre stanchions - 1 pair of sliding stanchions, movable along entire length #Insert slats - Wooden insert slats #Rear wall / rear corner posts - Steel corner posts up to lower edge of roof - Tarpaulin attachment with round tube and tensioning ratchet - Double-leaf rear portal doors, each with 2 internal cam bar locks #Tarpaulin - Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning buckles - Customer lettering Dachser on side tarpaulins and rear portal #Roof - Fixed roof with tarpaulin and roof bows, tarpaulin colour: white - Optimised rain gutter at rear on end bow, above doors #Country of registration / plates - Germany, Dekra inspection and expert report (§13 EG-FGV) - Fliegl manufacturer's certificate for body strength acc. to EN 12642 XL

Condition: used, Year of construction: 2007, functionality: fully functional, spindle speed (min.): 8,000 rpm, Long-turning lathe with a 10-station turret! Equipped with an FMB Turbo 3-36 bar feeder! TECHNICAL DETAILS Turning length: 320 mm Spindle speed (min.): 8,000 rpm Bar diameter: 32 mm Maximum drill diameter (front): 12 mm Rsdo Agnnkepfx Airoch Maximum thread drilling size (front): M12 Rear spindle speed: 8,000 rpm Number of tools: 25 to 27 MACHINE DETAILS Dimensions & Weight Dimensions (W x D x H): 2,860 mm x 1,465 mm x 1,900 mm Weight: 4,300 kg EQUIPMENT 10-station turret Rotating tools for complex machining tasks FMB Turbo 3-36

Condition: used, Year of construction: 2015, turning diameter max. 500 mm turning length 800 mm control sl Operate 3G ShopTurn Siemens swing diameter 500 mm distance between spindles 1.020 mm turning speed range - main spindle max. 5.000 min/-1 power capacity - main spindel 25 / 34 kW max. Torque 280 / 380 Nm spindle head 170h5 spindle diameter in front bearing 130 mm spindle bore 87 mm C-Axis 0,001 ° tool taper HSK 63 A number of toolpositions 80 pos. max. tool diameter 80 mm max. tool-dia with free toolbox 120 mm max. tool weight 12 kg max. tool length 300 mm Speed Milling Spindle max. 12.000 min/-1 power capacity - milling spindle 19 / 22 kW Torque 85 / 100 Nm tool taper HSK 63 A B-Axis +/- 110 ° x-axis -10 ... +490 mm y-axis +/- 100 mm z-axis 1: 845 mm z-axis 2: 600 mm z-axis 3: 800 mm Rcodpfsz S Nygex Airoh Spindle speed range subspindle max. 6.000 min/-1 power capacity - Sub spindle 20 / 27 kW bar material dia. 51 mm spindle bore diameter 73 mm spindle diameter in front bearing 100 mm C-Axis 0,001 ° total power requirement 85 kVA weight of the machine ca. 10,0 t dimensions of the machine ca. 7,0 x 2,9 x 2,6 m CNC - Turning- and Millingcenter DMG MORI - CTX beta 800 TC V6 - Viewings and availability from calendar week 47 / 2026! - 5-axis simultaneous machining - Main and counter-spindle - Swivel-type milling spindle - ShopTurn - Off-center turning and milling - Multi-thread cycle - Program state control - Tool sorting cycle - Easy Tool Monitor for Siemens control system - Chuck flushing system for main spindle - Chuck flushing system for counter-spindle - Differential pressure clamping - Coolant supply through the counter-spindle - Bar machining package for CTX beta (77 mm capacity) Workpiece the-take-off device (left side) Hydraulic hollow clamping system 4-color signal tower Interface for bar feeder or bar magazine - In-process workpiece measuring system (Renishaw) - Safety window cleaning system - Coolant spray gun

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, travel distance X-axis: 350 mm, travel distance Y-axis: 250 mm, travel distance Z-axis: 250 mm, AGIE CHARMILLES CUT 20 CNC wire erosion machine Manufacturer: GF AgieCharmilles Model: CUT 20 Year of manufacture: 2008 Control: AgieCharmilles CNC control Machine type: CNC wire erosion machine Rcodpfxoz Rz D Is Airoh Travel ranges: X-axis: 350 mm Y-axis: 250 mm Z-axis: 250 mm U/V axes: ±45 mm Working area: Max. workpiece dimensions: 900 × 680 × 250 mm Max. workpiece weight: 400 kg Max. taper angle: ±25° at a workpiece height of 80 mm Wire erosion system: Wire diameter: 0.15–0.30 mm Automatic wire threading Machining in a water bath Dielectric fluid: Deionized water Wire speed: approx. 30–330 mm/s Machine data: Connection voltage: 380 V / 50 Hz Machine weight: approx. 3,000 kg Machine dimensions: approx. 3,000 × 2,100 × 2,300 mm (L × W × H) Equipment: - CNC control AgieCharmilles - Automatic wire threading - U/V axes for taper machining - Dielectric fluid and filter system - Wire collection container - Handheld control unit According to the previous owner, the electronics have been extensively refurbished, with work carried out by Charmilles technicians.

Condition: used, Year of construction: 2000, Weiler DA 180 / 1000 - Universal lathes - ACU-RITE position display - 3-jaw chuck, Ø 200 mm - Quick-change tool holder - Coolant system - Work area lighting - Chuck guard - Chip guard - Various tool holders and tools - Operating manual - Year of manufacture: 2000 Technical data Main spindle: - Spindle head according to DIN 55027: Size 6 - Spindle bore: 52 mm - Ø in front bearing: 83 mm - Internal taper: metric 57 - Number of speeds: 12 - Speed range: 33–1500 rpm Tailstock: - Diameter of tailstock spindle: 65 mm - Morse taper: Mk 4 - Lead of leadscrew: 6 mm - Turning tool cross-section: 20 × 20 mm Rodpfj Agnynex Airsch Working ranges: - Swing over bed: 380 mm - Swing over cross slide: 185 mm - Travel of cross slide: 330 mm - Travel of top slide: 120 mm - Travel of tailstock spindle: 120 mm Feeds: - Longitudinal feeds: 0.072 – 4.038 mm/rev - Cross feeds: 0.036 – 2.019 mm/rev Threads: - Metric threads: 0.5 – 28 mm - Inch threads: 56 – 1 TPI - Module threads: 0.25 – 14 - D.P. threads: 112 – 2 Electrical connection: - Drive power: 5.5 kW - Motor rated speed: 1500 rpm Dimensions: - Center height above flat guideway: 180 mm - Center height above floor: 1060 mm - Bed width: 330 mm - Machine dimensions WxHxD: approx. 2400 x 1700 x 1200 mm - Machine weight: approx. 1800 kg

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2007, operating hours: 70,192 h, laser hours: 21,800 h, laser power: 2,700 W, TruMatic 6000 K01 (1600) Large-format, 2700 Watt Rcjdpfx Aie Afxvgjreh NC: 70192 h Laser on: 70000 h Beam on: 21800 h Sheetmaster Gripmaster+ shear Loading and unloading cart Fire extinguishing system Parts conveyor Options: Multishear Thread forming Marking/Signing

Condition: new, Year of construction: 2026, operating hours: 1 h, overall weight: 300 kg, total length: 3,200 mm, total width: 550 mm, total height: 700 mm, BOOSTON V-TURN-H – Hydraulic lifting module for timber prefabricated elements | 750 kg NEW – Modular system for lifting prefabricated elements, V-TURN We present the new BOOSTON solution – V-TURN-H, a hydraulic lifting module designed for the production of prefabricated walls and other timber construction elements. The device allows for lifting and rotating prefabricated elements from a horizontal to a vertical position. Thanks to its modular design, V-TURN can operate independently or in combination with other modules, creating a workstation tailored to individual production needs. TECHNICAL SPECIFICATIONS - Lifting capacity per module: 750 kg - Lifting capacity of a set of two modules: 1500 kg - Module length: 3200 mm - Width: 550 mm - Working height: 700 mm - Drive: hydraulic - Working pressure: 100 bar - Hydraulic connections: M22 thread STANDARD EQUIPMENT The price applies to one complete V-TURN-H module, equipped with: - Steel structure of the lifting module - Hydraulic lifting system - Hydraulic cylinder - Safety valves - Connections for an external hydraulic system NOTE: The module is supplied without an external hydraulic pump. To operate the device, it is necessary to connect a hydraulic power source that provides oil under a working pressure of 100 bar. The connection of hydraulic lines is made via M22 threaded connections. MODULAR DESIGN – ANY CONFIGURATION V-TURN modules can operate independently or in conjunction with fixed ER-02 mounting panels, which fill the space between the lifters. This allows for the creation of a single common mounting platform, enabling both the assembly and subsequent lifting of prefabricated elements. The system can be gradually expanded as production needs change. Rcsdpfx Aij Af Ukgjrsh ADDITIONAL OPTIONS ER-02/150 – fixed mounting panel with a length of 1500 mm ER-02/300 – fixed mounting panel with a length of 3000 mm Mobile hydraulic pump – independent hydraulic unit for powering V-TURN modules EXCEPTIONAL INTRODUCTORY OFFER! Possibility of purchasing from just 1 unit, also for the purpose of testing the device in your own production facility. It is possible to order a larger number of modules and a complete mounting platform. BOOSTON – A Polish manufacturer of machines and production lines for the prefabrication of timber houses.