Used Water Recycling System for sale (10,085)

Condition: new, Year of construction: 2024, Gold River SWZ-700 water separators Application description: The GOLD RIVER SWZ series separator has been designed for special tasks, it can cope with the most difficult materials that contain many properties that disturb the separation process in separators commonly available on the market. SWZ water separators separate heavy fractions (non-ferrous metals) from, among others, plastics in the process of recycling secondary raw materials. SWZ separator equipped with a four-section copper water system equipped with radial nozzles with variable linear geometry. The separator uses the latest divided type of separation mat. The development of a modern module for preliminary division and preparation of material guarantees the purity of recovered raw materials in a very short time (plastics, metals). Why a water system? Our device uses a system similar to that used in the gold recovery industry. We use water as a carrier and a force that affects the materials in a gentle way. In the water system, all particles with higher mass are gently washed out and separated, generating no losses during the entire separation process. The properties of water together with our proprietary solutions are unrivaled compared to, for example, air separators. SWZ type separators are used: Separation of heavy from light materials (metal granulates contaminated with plastic, foil, paper, cotton, fibers) Cleaning plastics after air separators (dry) Separation of metals in cable and non-ferrous metal recycling lines The SWZ-700 water separator, thanks to the use of the latest module, performs the separation process in a very short time, therefore it is characterized by a high hourly efficiency of separated material of approximately 1200 kg/h. Description of action: The material fed into the separator goes through the transport channel to the module for initial fraction division into its mass and humidity changes. Some of the material is separated at this stage. In the second part of the module, the humidity of the remaining batch changes. Then the material falls onto the separation table where the final fraction separation takes place. As a result of this process, we obtain valuable materials from both sides of the separator. Cjdpfjua Tbwox Abcjrh Construction description: The massive structure and the inertial drive of the separator are made of materials appropriately selected to withstand the overloads resulting from vibrations. The supporting frame ensures excellent stiffness and failure-free operation for many years. Due to the type of vibration drive, the design does not require the installation of a soil separator. Separation table equipped with hydraulic adjustment of the angle of inclination. The separation table has a special module for initial division of fractions into their mass and preparation for final separation. The water system has several water pressure valves. The water circulation in the separator is closed. There is no need for constant access to an external water source because the device works using the water already in the tanks. Based on experience and continuous research in our laboratories. We are able to provide you with separators individually adapted to the specific nature of the material being separated. In various versions and sizes. SWZ-700 separators are manufactured to individual order.

Condition: new, Year of construction: 2025, Built on order Vibrating sieve to filter the process water. Cedpfx Ajkzg Sdobcorh Process water is preferably used in a closed circuit. The authorities also see this as the ideal solution. Obtaining the permits for a recycling plant is greatly simplified by the use of a closed circuit and the costs of using the plant are significantly lower.

Condition: good (used), Young used vibrating sieve to filter process water. Crjdpsvy Dy Nofx Abcsh Made of 304 stainless steel, also suitable for salt solutions.

Condition: used, Year of construction: 2020, operating hours: 500 h, functionality: fully functional, machine/vehicle number: DSF-1020 SS, TIMEX Filtration System: TIMEX DSF 1020 SS Drum Stripper Filter Filter Model: TIMEX DSF 1020 SS Drum Stripper Filter Filter Type: Frame Type Flange Standard: EN 1092-1 (DIN2576) PN10 Application: N/A Service Fluid: N/A Csderf U Enopfx Abcorh Capacity: 30 m3 /h Quantity: 1 Unit Inlet TSS N/A Filtration Degree: 2000 µ Filtration Area: 6 m² Drum Diameter / Length: Ø1000 mm / L: 2000 mm Inlet & Outlet Connections: DN150, PN6 Flanged Drain Connection: DN50, PN6 Flanged Working Pressure Min/Max: by Gravity Max. Operation Temp: 55oC Operation Temp: N/A Gearbox Motor Power: 1.1 kW* Required Voltage: 400 V AC / 50 Hz / 3Phz Filter Body / Pipe / Flange Material: SS316L Stainless Steel Filter Screen Material: SS316L Stainless Steel Cleaning Mechanism: Compressed Air + Water Accessories * Control Board (Std.)

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, 1. Waterjet cutting system with accessories, year of manufacture 2005, machine number: 95 246, Model 4060D, including: 2. Machine details: - NC 4060 D (Duplex with 6 cutting heads for abrasive cutting) - 1 x cutting table: 4200 x 6700 mm - X-axis travel: 2750 mm Crodpfxsxgumco Abcsh - Y-axis travel: 6470 mm - Z-axis travel (height): 250 mm - Positioning accuracy (X/Y): +/- 0.075 mm/m - Repeatability (X/Y): +/- 0.05 mm - Feed rate X: 10,000 mm/min - Feed rate Y: 10,000 mm/min - Feed rate Z: 4,000 mm/min Technical specifications: - 1 x Fanuc GE 300 i (NANO CNC) SYSTEM Control functions • 15-inch color LCD display (resolution 1024 x 768) • Machine control panel • 1.5 GHz Pentium III processor • Vertical and horizontal soft key bars • Slim operator panel with QWERTY keyboard • 40 GB program storage (hard disk) • 2 MB RAM for part programs • Windows 2000/XP operating system • Hand-held control unit (remote control) for easy axis positioning – 1 x MPG unit – 6 x WJS standard cutting heads mounted on holders (2 x 3 pieces) – 6 x SM 3000 abrasive metering units – 1 x IGEMS Standard or Professional – 1 x documentation – 2 x abrasive storage tanks, 1,500 l each – 1 x sludge removal system, 3 x diaphragm pumps – 1 x wastewater tank 1,500 l – 1 x cascade tank – 1 x new stainless-steel cutting tank (4 x 6.7 m) - 10 m high-pressure hoses with fittings - 1 x KMT high-pressure pump, 100 HP, 4,100 bar, only 9,500 operating hours - Installation and maintenance by WJS personnel Machine connections: Electrical connection: 3 x 400 V+N+PE, 25 A, 50 Hz Compressed air supply: 600 l/min Air pressure (technically dried): 6.5 bar

Condition: new, Year of construction: 2025, Set of cones(concave + mantle) Maxtrak 1000 Medium Coarse - very good quality. 22%Mn, with SPECTROMETER CERTIFICATE, highest quality on market! Csdpfx Ajigvfvobcsrh Parts number: 603/9052-22 MC + 603/9106

Condition: excellent (used), operating hours: 2,658 h, functionality: fully functional, pressing force: 71 t, filling opening width: 1,000 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, oil tank capacity: 1,250 l, net weight: 29,000 kg, nominal current: 200 A, Technical data baler: Manufacturer BOA Recycling Systems B.V. Crjdpeu Thcvsfx Abcoh Type M75-45-A-5-1.6 Ecoline Year of construction 2021 Hours of operation 2,658 hours (as of May 2024) Number of pressed bales 42,212 pieces (as of May 2024) Press power main press 71,2 kN (71 t) Specific press capacity 9 kg/cm² Operating pressure 280 bar Cylinder stroke 2,200 mm Feed channel 1,620 x 1,000 mm Capacity per cycle time 2,4 m³ Theoretic cycle time 21 seconds Theoretic throughput rate 450 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Connected load 100 kW Current consumption 200 A Tying system 5-fold vertical, fully automatic, the press stamp is prepared for an additional 3-fold horizontal binding Throughput rate at a bulk weight of 30 kg/cbm approx. 13,6 tons/hour bulk weight of 50 kg/cbm approx. 24,2 tons/hour bulk weight of 100 kg/cbm approx. 36,4 tons/hour bulk weight of 150 kg/cbm approx. 54,7 tons/hour Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,250 l SPS controller Siemens S7 1500 Operating panel Siemens SIMATIC HMI TOUCH Transport dimensions of press 10,000 x 2,800 x 3,385 mm (l x w x h) Press height set up with feed chute 4,743 mm Press height with conveyor belt 7,123 mm Machine weight baler approx. 29 tons Noise level <85 dB (A) Condition of the baler: With 2,658 operating hours, the press is almost as good as new and in very good condition, has hardly any signs of wear and is ready for immediate use. Due to larger material input quantities, the pressing force and throughput of the machine no longer meet the customer's current requirements and is therefore being replaced by a new 120 tonne baler. Only the baler is for sale, without conveyor belt and wire drawing stations. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2025, condition: new, To sieve dry material: like flour-, grainy-, and granule-shaped material. Csdschb Ryjpfx Abcjrh Sizes from: wide 500-1500mm / length 1200-2400mm Sieve layers: 2 - 4 layers, granulation 0,1-18mm freely selectable.

Condition: new, Year of construction: 2025, Creating a cheap portable or mobile sand making plant involves optimizing costs while maintaining functionality and efficiency. Here's a basic outline of components and considerations for designing a cost-effective portable sand making plant: 1. Portable Sand Making Machine: - Select a cost-effective sand making machine that meets your production requirements. Consider factors like capacity, efficiency, and maintenance costs. - Look for options that offer good performance at a lower initial investment. 2. Screening Equipment: - Choose a portable screening unit to separate the sand into different sizes. This is crucial for producing high-quality sand with the desired particle size distribution. - Consider modular screening units that are easy to transport and set up. 3. Conveyor Systems: - Utilize conveyors to transport raw materials between different components of the plant. Opt for simple and reliable conveyor systems. - Explore cost-effective conveyor options that are easy to maintain. 4. Hopper and Feeder: - Incorporate a hopper and feeder system to ensure a continuous flow of raw materials to the sand making machine. This helps optimize the production process. - Choose a design that minimizes material spillage and wastage. 5. Power Source: - Consider energy-efficient power sources to reduce operational costs. This could include using generators or connecting to the electrical grid, depending on the availability and cost of electricity in your location. 6. Chassis and Mobility: - Opt for a simple and robust chassis design that allows for easy transportation. Depending on your needs, choose between wheels or tracks for mobility. - Aim for a design that facilitates quick setup and dismantling to save time and labor costs. 7. Control System: - Implement a user-friendly control system that enables operators to monitor and adjust the sand making process efficiently. - Consider automation features that enhance control and reduce the need for constant manual intervention. 8. Dust Control and Environmental Considerations: Cjdpfxsq N Ud Ij Abcerh - Integrate effective dust control measures to comply with environmental regulations and ensure a safe working environment. - Explore environmentally friendly features to align with sustainability goals. 9. Modular Design: - Consider a modular design for easy customization and scalability. This allows you to adapt the plant to varying production needs over time. 10. Used Equipment: - Explore the possibility of using refurbished or used equipment to cut down on initial costs. Ensure that the used equipment is in good working condition and can meet your production requirements. Remember that while cost optimization is important, it's crucial to maintain the quality and efficiency of the sand making process. Additionally, compliance with environmental regulations should be a priority. Always consider the specific requirements of your project and seek professional advice if needed.

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: NC3015, repeat accuracy: 0.01 mm, travel distance X-axis: 2,550 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 200 mm, positioning accuracy: 0.01 mm, type of input current: three-phase, input voltage: 400 V, table length: 1,500 mm, table width: 3,000 mm, pressure: 3,800 bar, water pressure: 3,800 bar, Equipment: safety light barrier, Complete water jet machine water jet Sweden 3015. Made in 2007 and have been in use since then. Serviced by water jet sweden all the time. Sheet size 3000x1500 mm. Fanuc cnc. Kmt 50 hp pump in excellent condition with a lot of spare parts. 200 L sand hopper and a sand container for 1000 kg. Unit for cutting under water is also included. The machine is in very good condition. It is emptied and we can load it on a truck. Please ask if you want more pictures or if you have other questions. We can also put you in contact with water jet Sweden who has maintained the machine and know all about it. Cedsw Sl Ezepfx Abcsrh

Condition: like new (used), Year of construction: 2020, operating hours: 250 h, functionality: fully functional, 1.1 TECHNICAL DATA 1 x Waterjet cutting machine, NCP 4020 D 1 x FANUC 31iB d 1 x IGEMS Professional 1 x BevelJet cutting heads for AWJ abrasive waterjet cutting 1 x Fixed cutting heads for AWJ abrasive waterjet cutting 2 x SM3000 feed systems 1 x KMT, Jetline 50 HP, 3.8 l/min, 4100 bar 1 x Cooling unit control cabinet 1 x Hose reel with spray nozzle 1 x Tool kit 1 x Machine zone safety guard 1 x PanelOne HMI operator interface "EDGECUT" 1 x Remote control for high-pressure pump 1 x Remote maintenance system 2 x Diaphragm pumps and 2 x extraction units 1 x Waste container 1000 l 1 x Pressure vessel 200 l or 2-ton abrasive online conveyor/online abrasive hopper 1 x Head protection package (zero-point measurement head 1) 1 x IGEMS 5X CAM 1 x MPG, portable handheld pendant Codpfexgua Asx Abcerh 1 x Rotary unit SS (chuck 240 mm) Price €21,000 1.1.1 MACHINE DATA Table size (W x D): 4200 x 2275 mm - Machining area (W x D): 3980 x 2010 mm - X-axis travel 2D: 3530 mm - X-axis travel 3D: 3220 mm - Y-axis travel 2D: 2010 mm - Y-axis travel 3D: 1405 mm - Z-axis travel: 250 mm - Positioning accuracy (X/Y): +/- 0.050 mm/m - Repeatability (X/Y): +/- 0.025 mm - Rapid traverse (X-axis): 30,000 mm/min - Rapid traverse (Y): 15,000 mm/min - Rapid traverse (Z): 5,000 mm/min - Minimum distance between nozzles: 450 mm - Maximum distance between nozzles: 2,010 mm 1.2 CONNECTION DATA 1.2.1 MACHINE CONNECTION • Electrical connection: 3 x 400 V+PE, 16 A, 50 Hz • Pneumatic supply volume (incl. pressure vessel): 500 l/min • Pneumatic supply pressure: min. 6.5 bar 1.2.2 HP PUMP DATA/CONNECTION HP pump data: - KMT 50, Jetline, 4100 bar - 37 kW, circuit breaker at 400/50 Hz, 80 A CAD/CAM software: - IGEMS Professional

Year of construction: 2025, condition: new, Overband magnet Crsdpfx Abeh U R Tgscjh Length: 2500 mm Height: około 400 mm Width: 1000 mm Belt width: 750 mm Magnet width: 500 mm Magnet length: 1044 mm Power: 1,5 kW(hydraulic or electric) Magnet field: 400 Gauss(may catch 100 mm pieces from maximum distance 300 mm Overband new, 12 months warrenty,

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, nominal current: 238 A, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Csdpfxjvf E Avs Abcerh Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 2025, condition: new, Circle Sievemachine to sieve dry material: like flour-, grainy-, and granule-shaped material. Sizes from: wide 500-1500mm / length 1200-2400mm Sieve layers: 2 - 4 ply, granlulation < 18mm freely selectable. Crodpfxjbcngie Abcsh

Condition: new, functionality: fully functional, Year of construction: 2025, A sand aggregate or gravel production plant is a facility where raw materials like sand, gravel, and other aggregates are processed to create various products used in construction and other industries. These facilities typically involve a series of processes to transform raw materials into the final products. Here is a general overview of the key components and processes involved in a sand aggregate or gravel production plant: 1. Mining and Extraction: - The process starts with the extraction of raw materials from quarries or mines. Heavy machinery such as excavators, loaders, and bulldozers are used to remove the raw materials from the earth. 2. Crushing and Screening: - The extracted raw materials often need to go through crushing and screening processes to reduce their size and separate them into different grades. - Crushers break down large rocks into smaller pieces, and screens sort the particles based on size. 3. Washing: - Washing is a common process to remove impurities such as clay, silt, and dust from the raw materials. This is particularly important for sand and gravel used in construction. 4. Grading and Sorting: - After washing, the materials may go through grading and sorting processes to separate them into different sizes and qualities. 5. Storage and Stockpiling: - Processed materials are often stored in stockpiles for further use. Adequate storage facilities are necessary to manage different grades of materials. 6. Conveying and Transportation: - Conveyor systems are used to transport materials between different stages of the production process. Transportation methods, such as trucks or conveyor belts, are used to move the final products to distribution points. 7. Quality Control: - Quality control measures are implemented to ensure that the final products meet the required specifications and standards. This may involve regular testing and analysis of the materials. 8. Environmental Considerations: - Sustainable practices and environmental considerations are crucial in the operation of a production plant. Measures such as dust control, water recycling, and rehabilitation of mined areas are often implemented to minimize the environmental impact. 9. Maintenance and Safety: - Regular maintenance of equipment is essential for the smooth operation of the plant. Safety measures are also critical to protect workers and ensure compliance with regulations. Crsdpfoq Nia Ijx Abcoh 10. Final Product: - The final products from a sand aggregate or gravel production plant may include various grades of sand, gravel, crushed stone, or other types of aggregates used in construction, concrete production, asphalt production, and other applications. It's important to note that the specific processes and equipment used in a production plant may vary based on the type of raw materials, the intended final products, and local regulations. Additionally, advancements in technology and sustainability practices may influence the design and operation of such facilities.

Condition: new, Year of construction: 2025, In stock: The STF 3.0 floating sink separator with our highly efficient SP1000 Mk2 centrifuge and our VS1 water screen. A compact but powerful washing system that is low-maintenance and can wash/sort up to 3000 kg/h of hard plastics. The machines are made entirely of 304 stainless steel, so salt solutions can be used without any problems. An excellent starting point for a good homemade zinc float installation. Crsdpfx Abexhf Nweceh The machines are in stock and can therefore be delivered within a week. Ask us for further information.

Condition: like new (used), Baktec water Dosing machine and chiller In good working condition for more information please sent an request Cedpfx Absump Axjcerh

Condition: like new (used), Year of construction: 2023, New, never used collapsible 10.000 gallon (37,854 liter) water or fuel storage with all accessories and documents. Located locally in Hungary (EU), Vacegres. Crodpfoxcgagex Abcsh

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Cedou Thkaopfx Abcerh Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2025, condition: new, Circle Sievemachine to sieve dry material: like flour-, grainy-, and granule-shaped material. Sizes from: wide 500-1500mm / length 1200-2400mm Codpebcnatofx Abcsrh Sieve layers: 2 - 4 ply, granlulation 0,1-18mm freely. selectable.

Condition: new, Year of construction: 2025, functionality: fully functional, power: 55 kW (74.78 HP), ### Introduction to Jaw Crushers A jaw crusher is a type of primary crusher used in mining and ore processing plants. It works by using compressive force to break down large rocks into smaller, more manageable pieces. The machine consists of a fixed jaw and a movable jaw, which together create a V-shaped cavity called the crushing chamber. The movable jaw exerts force on the rock by forcing it against the stationary plate, causing it to break. Key Components: - Fixed Jaw Plate: Mounted in a fixed position. - Movable Jaw Plate: Mounted on a pitman that moves in a reciprocating motion. - Flywheel: Provides the necessary inertia for the crushing action. - Toggle Plates: Serve as a safety mechanism, ensuring that the jaw crusher operates efficiently and prevents damage. ### Working Principle The working principle of a jaw crusher is based on the reciprocating movement of the movable jaw against the fixed jaw: 1. Feeding: Large rocks are fed into the top of the crusher. 2. Crushing: As the movable jaw moves back and forth, it crushes the material against the fixed jaw. 3. Output: Crushed material is discharged from the bottom of the crushing chamber. ### Applications of Jaw Crushers Jaw crushers are versatile and can be used in a variety of industries and applications, including: 1. Mining and Mineral Processing: Cjdpfsq Nf Tvsx Abcorh - Primary crushing of mined ore (gold, copper, iron, etc.). - Size reduction of rocks to facilitate further processing (e.g., milling). 2. Construction and Demolition: - Crushing of concrete, bricks, and other construction materials. - Recycling of building materials to create aggregate for new construction. 3. Aggregates Production: - Crushing of raw materials to produce aggregates for concrete and asphalt. - Production of road base and railway ballast. 4. Industrial Applications: - Crushing materials in chemical processing plants. - Size reduction of materials for production processes in various industries. 5. Environmental Management: - Processing of materials for landfill cover. - Recycling operations to reduce waste and promote sustainable practices. ### Advantages of Jaw Crushers - High Crushing Ratio: Capable of producing a range of material sizes with a single pass. - Durability and Reliability: Built to withstand heavy-duty use and harsh conditions. - Simple Structure: Easy to maintain and repair, with fewer components compared to other types of crushers. - Versatility: Suitable for various types of materials and a wide range of applications. - Energy Efficiency: Efficiently uses energy, making it cost-effective for operations. ### Examples of Use Cases - Mining Operations: Jaw crushers are used as primary crushers in mine sites to crush large rocks before being processed further in the milling process. - Construction Sites: Used to break down concrete and other building materials for recycling and re-use. - Aggregate Production: Integral in producing the base materials for construction and infrastructure projects. - Demolition Projects: Efficiently crushes and recycles materials from demolished structures. By understanding the introduction and applications of jaw crushers, businesses can make informed decisions about integrating this machinery into their operations for efficient and effective material processing.

Condition: new, Year of construction: 2025, In stock: The STF 3.0 floating sink separator with our highly efficient SP1000 Mk2 centrifuge and our VS1 water screen. A compact but powerful washing system that is low-maintenance and can wash/sort up to 3000 kg/h of hard plastics. Crodoxhf H Nepfx Abcjh The machines are made entirely of 304 stainless steel, so salt solutions can be used without any problems. An excellent starting point for a good homemade zinc float installation. The machines are in stock and can therefore be delivered within a week. Ask us for further information.

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Crodpfx Abjxbgnhecjh Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, functionality: fully functional, Year of construction: 2025, Small stone jaw crusher with vibrating screen powdered by diesel engine Max input size: 210mm Capacity: 15-22 t/h Output size: 0-5mm, 5-10mm, 10-22mm, 22-31mm Csdpfxoq I Nvio Abcorh Diesel engine: 28HP

Condition: new, functionality: fully functional, Year of construction: 2025, Product overviews of Waste Industrial Timber Wood Pallet Double Shaft Shredder Shredders can generally be used to shred hard-to-break plastics, rubber, large tires, large nylon materials, large pieces of fishing nets, fibers, paper, wood, electrical devices, cables, PET bottles, cardboard, wood, plastic barrels, etc. Solid objects. The main function of the equipment is to squeeze the bulk materials and large-diameter drum metal materials that are not convenient for transportation through the shear of the shredder, and shred them into sheets that meet the requirements. The main structure of the double-shaft shredder is a feed hopper, a knife roller, a driving device, a bearing, a hydraulic system, and an electric control box system. Working principle: All kinds of waste materials enter the shredding chamber through the feeding hopper. The double-knife rollers do relative rotation to shred and cut the materials, and then the materials are discharged from the shredder to achieve the shredding of large pieces of materials. Applicable materials and fields Double shaft shredder is one of ethential equipment for waste recycling in following fields and materials: +Bulky Waste: Sofa,Mattress,Chair, Funiture,Windows,etc +Industrial Waste: Textiles,Leather,Rubbers, Leathers ,General industrial waste,etc Crjdpsvn D I Nefx Abcoh +Hazardous Solid waste: Medical waste,Paint sludge,Radioactive waste,Hazardous waste oil drum,Jumbo bag,etc +Paper waste: Carton,Cardboard,Book,Newspaper,Document,Brochure,Packaging paper,etc +Garden waste: Branch, Wood pallet, Trunks, Boards,etc +Domestic waste +Biomass straw: Straw, Bamboo, Corn, Sorghum straw, Bean straw, Fruit shell, Palm shell, etc +Scrap metal: Car Shell, Aluminum casting, Household appliances, Scrap light metal,Automobile hub,etc +Paper mill waste: Paper mill slag, Paper mill rope, Paper mill offcut,etc +Wood pallet, scrap furniture, waste chair, tree roots recycling, etc. Double shaft shredder main body: The main body is welded with excellent steel plate to ensure the stability of the equipment under heavy load for a long time. Bearing: The bearing seat is split and easy to disassemble, and the movable knife, fixed knife, bearing and other parts can be quickly removed, and it is easy to maintain and replace the knife. The sealing structure can avoid the contact of broken materials and grease, and can also protect bearings and gears when handling liquid materials.