Used Weiler Ergodor for sale (202)

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and feed spindle table lathe in excellent condition! Pgsdpfsv Tyzcsx Aahju Technical specifications: >> Machine no. 2801 >> Center height 120 mm >> Center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle bore 23 mm >> Short-taper spindle head DIN 55027 >> Tailstock MT 2 >> Feed rates from 0.03 to 0.15 mm/rev >> Possible thread sizes: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x Röhm 125 mm three-jaw chuck with 4 sets of jaws >> Collet chuck with collets from 2 mm to 12 mm, increments of 1 mm Drawbar >> Multifix size A with 4 tool holders >> Change gears >> Fixed steady rest >> Faceplate >> Spindle cover >> Clamping tool About the machine: Offered is a Weiler Primus table lathe with guide rail and drawbar in very good condition. The machine is fully functional. All slides run very smoothly and evenly. Even at high speeds, the Weiler runs quietly. The Primus comes from a state-owned company where it was used little. This newer generation of Weiler lathes is very user-friendly, and surfaces can be produced with a polished finish. Take advantage of the opportunity to view this machine on-site under power and see for yourself its condition. (The base cabinet is included; the machine is not bolted to the machine.) A digital display is available for an additional charge.

Condition: excellent (used), functionality: fully functional, spindle bore: 40 mm, center height: 165 mm, center width: 750 mm, Dear Sir or Madam, For sale is a Weiler Condor B lathe. This model is particularly notable for its very user-friendly operation and an excellent space-to-center height/center distance ratio. The Condor B is sized between the Weiler Praktikant and the Weiler Commodor, making it a genuine all-rounder for any workshop. The machine undergoes a thorough partial overhaul in our shop to ensure it is in excellent technical and visual condition. All guideways are in good order, the gearboxes run quietly, and all levers are easy to operate. You are welcome to inspect the machine on-site to verify its condition yourself. Availability: on request Center height: 165 mm Center distance: 750 mm Spindle bore: Ø 40 mm Tailstock taper: MT3 Chuck mounting: short taper DIN 55027 size 5 with bayonet lock Quill travel: 85 mm Spindle speeds: 22–2800 rpm Thread types possible: Metric, Imperial, Module, Diametral Pitch Pgodpfxsw N Np Se Aahou Metric thread pitches: 0.18–28 mm Spindle brake: switchable Voltage: 400V Dimensions: approx. 1.80 x 1.30 x 0.9 m (LxHxW) Weight: approx. 1100 kg Further equipment and accessories: 3-axis digital readout K+C (NEW), chuck guard (NEW), coolant system, 2x emergency stop, leadscrew and feed shaft cover (optional), operating manual, and much more on request... Our service commitment to you: - We are a certified master machine engineering business - All machines are at least workshop-tested - All lubricants and any worn components are replaced prior to sale - On request, we offer complete or partial overhaul of your selected machine - On request, we can repaint your chosen machine in any color you wish - Additional accessories such as tooling can be ordered with the machine upon request - On request, we can also install further accessories such as safety devices - We are happy to handle shipping and/or on-site installation for you

Condition: good (used), Centre distance: 450 mm Centre height: 120 mm Spindle bore: 23 mm Speed: 40 – 3000 rpm Infinitely variable drive with 3 gearbox stages and digital speed display Tailstock: MT 2 Drive power: 1.5 kW Weight: 350 kg Dimensions: 1200 x 650 x 1330 mm Paint: Reseda green RAL 6011 Digital display: Optional at extra cost Pgsdpfxjw I A Uxs Aahou Accessories: Further accessories available on request

Condition: excellent (used), Year of construction: 2001, turning diameter 330 mm turning length 750 mm control WEILER D 1 Pgsdpfxowi Ugqs Aahju centre height 165 mm centre distance 750 mm swing diameter over face slide 160 mm spindle bore 42 mm spindle turning speed range 1 - 4500 U/min spindle head DIN 55027 Gr. 5 face slide travel 180 mm feeds X-axis mm/U feeds Z-axis mm/U rapid traverse X-axis 5 m/min rapid traverse Z-axis 10 m/min feed power X/Z axis 3000 / 6000 N tailstock taper MT 3 tailstock quill diameter 50 mm tailstock quill stroke 110 mm total power requirement 10 kW weight of the machine ca. 1,3 t dimensions of machine L x W x H 1,8 x 1,2 x 1,7 m Accessories: 3-jaw chuck SCHUNK 0 mmø, changing tool post, coolant

Condition: used, Year of construction: 1997, - 4-jaw faceplate Ø 550 mm - 3-jaw lathe chuck Ø 310 mm incl. 4 sets of hard base jaws, 1 set of hard top jaws, 8 sets of soft top jaws - Fixed steady rest - rotating center point MK5 - Mulifix B quick-change holder incl. 10 tool holders - Switch-on time 32582 h - Year of manufacture 1997 - incl. operating instructions and technical documentation Technical data: Working range: - Tip width: 1000 mm - Center height: 280 mm - Circumferential diameter over bed: 570 mm - Circumferential diameter over facing slide: 340 mm - Bed width: 350 mm - Movement of the facing slide: 340 mm - Movement of the top support: 140 mm - Slide gate length: 700 mm - Slide width: 220 mm - Bed slide guide length: 560 mm - Turning tool cross-section (height/width): 32 x 25 mm Turning spindle: - Spindle head according to DIN 55027: size 8 - Spindle diameter in front bearing: 100 mm - Spindle bore: 66 mm - Inner taper of the main spindle: metr. 70 Main drive: - Drive power 60% / 100% ED: 15 / 11 kW - Max. Torque at the turning spindle: 1600 Nm - Total speed range: 1 - 2500 rpm - Speed range gear stage I: 1 - 625 rpm - Speed range gear stage II: 4 - 2500 rpm Feed drive: - Type: Three-phase servo drives - Feed range longitudinal and planar: 0 - 10 mm/rev - Feed force longitudinal: 9000 N - Feed force planar: 7000 N - Input speed longitudinal/plane: 7 / 3.5 m/min Tailstock: - Quill diameter: 70 mm - Quill stroke: 160 mm - Inner taper of the quill: MK5 Thread cutting range: - Metric threads: 0.1 - 250 mm - Inch thread: 1/4 - 56 G/1" - Module thread: 0.125 - 28 - DP thread: 1 - 224 Pedpfxer Hrq Dj Aahsgu Machine dimensions: - Dimensions WxHxD: 2850 x 1750 x 1815 mm - Weight of the machine: 2950 kg

Condition: used, turning diameter over bed / mm turning diameter over slide rest / mm Pgedpfjwgi Tmsx Aahju turning length / mm

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, Weiler Praktikant 160 B lead and feed screw lathe with 3-axis digital readout K&C NEW Technical data: >> Year of manufacture: 1986, machine number 86-160-348 >> Center height: 160 mm >> Distance between centers: 650 mm >> Spindle speeds: 8 steps; from 96 to 2500 rpm >> Spindle bore: 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: 0.02 to 0.63 mm/rev >> Usable threads: metric, inch, module, and diametral pitch >> Metric thread pitches: 0.25 to 8 mm >> Weight: approx. 680 kg >> Spindle brake switchable >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital readout from K&C, new, 12 months manufacturer warranty with operating manual Functions: mm/inch switching, coordinate selection ABS/INC, value halving, reference point, tool programming for 200 tools, taper calculation, radius/diameter display, quick zeroing, direction reversal >> Collet clamping device, collets as new from 1 to 29 mm in 1 mm increments >> 160 mm new three-jaw chuck with 2 sets of jaws >> Multifix size A with 3 tool holders >> Electric chuck guard >> Bed stop >> Rear wall >> Machine leveling feet >> Coolant device About the machine: Pgjdpfjwthbisx Aahju Offered is a Weiler Praktikant 160 B lead and feed screw lathe built to toolroom precision in very good condition. The machine is, of course, fully functional. The Weiler was completely dismantled and newly painted in light grey. All slides move very smoothly and evenly. Even at high speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and can produce surfaces as if ground. Take the opportunity to inspect the machine under power on site and verify its condition for yourself.

Condition: reconditioned (used), Year of construction: 1989, Universal lead and spindle lathe Make: WEILER Model: Condor B Year of manufacture: 1989 - overhauled newly painted RAL 7035 light gray Mach. No.: 1401 with guarantee Accessories: - 3-A digital display FAGOR Innova 30i T, new - Chuck protection hood with electrical fuse, new - Quick-change tool holder base body size B - Bed stop Pgsdpfx Aog R S Rcjaheu - Coolant device - Chip back wall - Operating instructions -used, as seen -

Condition: good (used), Weiler Condor VS 2 center lathe and feed spindle lathe Technical data: Center height 160 mm Center width 800 mm Spindle bore 40 mm Bed width 240 mm Speeds 12 - 2800 min-1 Drive power 3 kW Tailstock holder MK 3 Quill stroke 110 mm Feed rates 0.037 - 1.253 mm/rev Weight, approx. 800 kg Dimensions (WxDxH), approx. 1930 x 880 x 1470 mm Psdpfxeu E H Iwo Aahegu Equipment: 3-jaw lathe chuck Quick-change holder system Multifix size A incl. 1 change holder Electrically locked chuck guard Brake motor retrofitted Bed stop Emergency stop button Coolant device Machine light Chip back panel ELESTA 3-axis digital display Moving tip The machine has been technically inspected and is in very good condition. Backlash face spindle 0.2mm Top slide backlash 0.15mm Inspection under power possible at any time. Price net free loading ex warehouse

Condition: as good as new (ex-display), Year of construction: 2013, operating hours: 2,100 h, turning diameter over cross slide: 200 mm, spindle bore: 66 mm, turning diameter over bed slide: 435 mm, center height: 217 mm, turning length: 1,000 mm, total length: 3,061 mm, spindle speed (max.): 3,500 rpm, spindle speed (min.): 1 rpm, bed width: 202 mm, For sale: WEILER E40 Precision Lathe – only 2100 hours on the clock, Machine condition as new. Features a 435 mm swing over bed, 200 mm swing over cross slide, 66 mm spindle bore, and a 1,000 mm turning length. Perfect for workshops needing accuracy and durability. Contact for pricing and details! Psdpfx Asv A Irzeahsgu

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, Lead and tailstock lathe Weiler Condor 81 *Partially overhauled*Item number: 04-03-141Manufacturer: WeilerVery good general conditionMachine partially overhauledDelivery time: on request - subject to prior saleYear of construction: approx. 1986Dimensions (L x W x H): approx. 2000x1000x1700mmWeight: approx. 900kgDigital display: 3-axis digital display Sino *New*Dimensions:Max. turning diameter over bed: approx. Ø340mmMax. turning diameter over support: approx. Ø185mmMax. turning length: approx. 800mmBar passage: approx. Ø42mmSpindle:Speed range: approx. 30-2800 RPMSpindle nose: A 2-5Driving power: approx. 3.0kWAutomatic longitudinal & cross feeds:Feed range: approx. 0.016-0.50mm/RSuitable for threads:Metric 0.18 – 28 mm Inch 80 – 1 Gg/"Diametral pitch threads 200 – 2 3/4 Dp Module 0.1 – 9Tailstock: MK3Accessories:3-axis digital display SINO *New*3-jaw chuck 160mm *New*Quick-change holder size E + 1 insertBed stopWorking light *New*Coolant system *New*Complete documentationNOT – offVarious clamping wrenches.  Machine feet Electric feed protection *New* Guide and lead screw cover *New* Drill chuck *Optional* Follow-up tip *Optional* additional quick-change holders *Optional* Podpfx Aaewl At Dshjgu

Condition: new, Intern VC plus The new dimension in the field of conventional precision lathes. High-quality, energy-efficient, precise and universally applicable in production, training and further education. It convinces through: future-oriented technology highest accuracy durability user-friendly ergonomics smallest footprint and extensive accessories. The consistent and innovative further development of the practice-proven Praktikant series is the economical and intelligent solution for your daily applications. Technical data: WORKING RANGE Center height 160 mm Swing over bed 320 mm Swing over cross slide 190 mm Center width 650 mm ROTATING SPINDLE spindle head DIN 55027/DIN ISO 702-3 size 5 spindle bore 43 mm Spindle diameter in front bearing 70 mm MAIN DRIVE drive power 60 %/100 % ED - / 8 kW speed range 25 - 5.000 min-1 Number of speeds stepless FEED RANGE Number stepless longitudinal 0.01 - 6 mm/rev plane 0.003 - 2 mm/rev THREAD CUTTING RANGE Metric thread 0.1 - 20 mm REITSTOCK quill diameter 40 mm quill stroke 85 mm Inner taper DIN 228 MK 3 ACCEPTANCE ACCURACY DIN 8605 Equipped with WEILER WTS 15 VC plus screen display - Large, clear 15" touch screen, rotatable and tiltable, resolution 1366 x 768 - Change of operating screens via swiping movements - Operating functions can be called up via App Manager Pedpfx Ajhw N Ntjahjgu - Control panels can be freely configured,

Condition: like new (used), functionality: fully functional, Weiler center lathe Model Condor 81 guidance and feed spindle lathe with 3-axis digital display from K&C, NEW Geometrically overhauled with inspection protocol for new machine tolerances Technical data: >> Machine No. 84-121 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: metric, imperial, module, and diametral pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Equipment and accessories: >> 3-axis digital display from K&C, new, 12 months manufacturer warranty with operating instructions Functions: switching mm/inch, coordinate selection ABS/INC, value halving, reference mark, tool programming for 200 pcs., taper calculation, radius/diameter, quick zeroing, count direction switching >> Collet chuck NEW, collets NEW from 3 to 26mm, increments of 1mm >> 160 mm three-jaw chuck with 2 sets of jaws NEW >> Multifix size B NEW with 3 piece steel holders >> Bed stop >> Electric chuck guard NEW >> Rear wall >> Operating manual Pgodpfx Aaswrm Dtsheu >> Coolant device >> Machine feet About the machine: A Weiler Condor 81 guide and feed spindle lathe in a very good, geometrically overhauled condition is being offered. The guides are newly ground or newly scraped. Inspected according to test protocol. The accessories collets and chuck are new. For safety: The machine has a brake motor, electronic spindle guard and two emergency stops, making it an absolutely as-new lathe. Even at high speeds, the Weiler runs very smoothly. This newer generation of Weiler lathes is very user-friendly and allows surfaces as if ground to be produced. Take the opportunity to view this machine on site under power and convince yourself of its condition.

Condition: refurbished (used), Year of construction: 2007, Universal lead and feed spindle lathe Make: WEILER Model: Primus VC Year of manufacture: 2007 - overhauled newly painted RAL 7035 light gray Mach. no.: CK17 Center height: 140 mm Center width: 500 mm Spindle bore: 40 mm with guarantee geometric acceptance with test report Accessories: - 3-A digital display SIEMENS - Chuck protection hood with electrical protection - Drive motor braked - Quick-change tool holder base body size A - Bed stop Pgsdpfxjv D Ip No Aaheu - Covered lead and feed spindle - Chip rear wall - Pull-out chip tray - Operating instructions - Used, as seen -

Condition: good (used), Year of construction: 2014, drilling capacity: 60 mm, spindle mount: MK 5, Manufacturer: WEILER MAS Type: VOM 50 Year of manufacture: 2014 Specifications Metric US Standard Arm length 1250 mm Max. drill Ø (iron) 50 mm Max. Tap diameter 48 M Quill stroke 350 mm Max. distance spindle - table 1555 mm Min. distance spindle - table 305 mm Speed 800 rpm Tool holder 5 ISO/Bt/Mk Pjdpjwpkr Nsfx Aahsgu Column diameter 400 mm Dimensions (estimated) Length 3200 mm Width 1325 mm Height 2970 mm Weight 6750 kg Please note: The information on this page has been provided by us to the best of our knowledge and, as far as possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, no representation or contract conditions will be provided. We recommend that you verify all important details.

Condition: good (used), Year of construction: 1996, Weiler lathe Type Condor B Center height 165 mm Center width 750 mm Rotation over bed 330 mm Rotation over cross slide 185 mm Spindle head DIN 55027 size 5 Spindle bore 40 mm Inner taper main spindle MK 5 Connected load 3 kw Speed 22-2800 rpm Pgodpfsvbwd Rsx Aahju Tailstock MK 3 Weight 1040 kg 3 jaw lathe chuck 4 jaw lathe chuck Multifix B Rotating center punch

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, Lead Screw and Feed Rod Lathe Weiler Commodor Partially Overhauled Item number: 04-03-117 Manufacturer: Weiler Very good overall condition Machine partially overhauled Delivery time: on request – subject to prior sale Technical Details: Year of manufacture: approx. 1991 Dimensions (L x W x H): approx. 2200 x 1200 x 1800 mm Weight: approx. 1500 kg Digital Readout: 3-axis digital readout Sino New Capacity: Max. swing over bed: approx. Ø380 mm Max. swing over cross slide: approx. Ø190 mm Max. turning length: approx. 1000 mm Bar capacity: approx. Ø56 mm Spindle: Speed range: approx. 25–2000 rpm Spindle nose: A2-6 Drive power: approx. 4.0 kW Pedpfx Aowf Dhpjahsgu Automatic longitudinal and cross feeds: Feed range: approx. 0.011–0.80 mm/rev Thread Cutting Capabilities: Metric threads: 0.30–10 mm Inch threads: 80–2 3/4 TPI Diametral pitch threads: 80–5.5 DP Module threads: 0.2–5 Tailstock: Taper: MT4 Accessories: 3-axis digital readout SINO New 3-jaw chuck 200 mm New Quick-change toolholder size B + 1 insert Bed stop Work light New Coolant system New Complete documentation Emergency stop (E-Stop) Various chuck keys Machine feet Electrical chuck guard New Leadscrew and feed rod cover New Optional Accessories: Drill chuck Live center Collet chuck 173E Collet set 173E Additional quick-change toolholders Further accessories available on request. Price and further technical details available upon request.

Condition: like new (used), functionality: fully functional, Weiler Praktikum 160B precision center lathe 3-axis digital display K&C NEW. Reconditioned with acceptance certificate for tolerances of new machines Technical data: >> Machine no. 87 160 760 >> Center height 160 mm >> Center width 650 mm >> Spindle speeds: from 24 to 2500 rpm >> Spindle passage 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.02 to 0.63 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight approx. 680 kg >> Spindle brake can be switched on >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching the counting direction, >> Collet device New, collets NEW from 3 to 25 mm, 1 mm increasing Pgodpfx Aaovrdlcjhju >> Three-jaw chuck 160 mm New with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Electronic spindle protection >> Machine lamp LED New >> Machine feet NEW >> Splash guard >> Operating instructions, spare parts plan (PDF) About the machine: Offered is a Weiler Praktikum 160 B guide and feed spindle lathe with toolmaker precision in a completely geometrically overhauled condition. Reconditioned with acceptance certificate for tolerances of a new machine. For safety: Electronic spindle protection of the work spindle, cover of the lead and feed spindle, 2 emergency stops and a brake motor. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: reconditioned (used), Year of construction: 1990, Universal lead and feed spindle lathe Make: WEILER Model: Praktikum 160 B Year of manufacture: 1990 - overhauled newly painted RAL 7035 light gray Mach. no.: 90-160-2054 Center height: 160 mm Center width: 650 mm geometric acceptance with test report Accessories: - 3-axis digital display FAGOR Innova 30i T - covered lead and feed spindle - braked drive motor - coolant system Pgsdpfx Aaohy Tdyohou - electrically secured chuck protection hood - quick-change tool holder size A - simple bed stop - chip back wall - operating instructions with guarantee used as seen The machine is technically corresponding to the state of the year it was built.

Condition: used, Year of construction: 1970, Weiler lathe with tailstock Pgjdpfshtnu Tjx Aahsu

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Technical data: >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Pgodpfxsvtp Edj Aahju Accessories and equipment: >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection About the machine: A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: reconditioned (used), Year of construction: 1974, Universal lead and spindle lathe Make: WEILER Model: Commodor Year of manufacture: 1974 - overhauled newly painted RAL 7035 light gray Mach. no.: 0068 Center height: 180 mm Center width: 1000 mm Pgsdpfx Aomgaddeahsu Spindle bore: 56 mm with guarantee geometric acceptance with test report Accessories: - 3-axis digital display FAGOR Innova 30i-T new - Chuck protection hood with electrical protection - Quick-change tool holder size B - simple bed stop - Coolant device - Operating instructions - used, as seen -

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and feed screw lathe from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck 160mm with 1 set of jaws >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1 mm to 20 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Fence >> Change wheels To the machine : Pgjdpfxou Aftgs Aahsu We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: like new (used), functionality: fully functional, Weiler center lathe model Condor B lead and feed spindle lathe with 3-axis digital readout from K&C NEW Geometrically overhauled with acceptance certificate for tolerances of new machines !!! Technical data: >> Machine no. 90-1495 >> Center height 165 mm >> Center width 750 mm >> Spindle speed : from 22 to 2800 rpm >> Spindle clearance 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.015 to 0.46 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake can be activated >> Length 1.83 m, height 1.29 m, depth 0.88 m Accessories and equipment: >> 3-axis digital readout from K&C New , 12 months manufacturer's warranty with operating instructions Functions : Switching mm/inch , Coordinate selection ABS/INC , Halving of the display value , Reference mark , Tool programming 200 pcs. , Cone calculation , Radius / diameter , Quick zeros , Switching the counting direction , >> Collet chuck device, collets NEW from 3 to 26 mm 1 mm increasing >> Three-jaw chuck 160 mm with 2 sets of jaws NEW >> Mulifix new size A with 2 steel holders new >> Bed stop >> elec. Chuck guard NEW Podpfxovambco Aahegu >> Machine lamp LED New >> Rear panel >> Operating instructions >> Coolant device >> Machine feet To the machine : We are offering a Weiler Condor B lead and feed spindle lathe in a geometrically overhauled condition, absolutely as good as new. The guides are newly ground and scraped. With acceptance according to test protocol. A very nice machine with electronic spindle protection. The accessories collets, chuck, Multifix are new. Spindles, spindle nuts, bearings, belts, wipers have been renewed. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and pull spindle lathe with 2 axis digital readout Heidenhain from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm Podpfx Aaou Afqlohjgu >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 2-axis digital readout from Heidenhain >> 1 new three-jaw chuck 125 mm with 2 sets of jaws >> collet chuck device new with collets new from 3 mm to 25 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Back plate To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.