Used Weiler for sale (179)

Year of construction: 1977, condition: used, Weiler Matador VS2 lathe year ca.1977 with collets , collet tube , three-jaw chuck , Multifix. Guide in the front area shrunk. Machine in a ready to use condition , After consultation under power ready for demonstration. Bedpfjmdn Dxox Abcjwh

Condition: refurbished (used), Year of construction: 2007, Universal lead and feed spindle lathe Make: WEILER Model: Primus VC Year of manufacture: 2007 - overhauled newly painted RAL 7035 light gray Mach. no.: CK17 Center height: 140 mm Center width: 500 mm Spindle bore: 40 mm with guarantee geometric acceptance with test report Accessories: - 3-A digital display SIEMENS - Chuck protection hood with electrical protection - Drive motor braked - Quick-change tool holder base body size A - Bed stop - Covered lead and feed spindle - Chip rear wall - Pull-out chip tray - Operating instructions Bodpov D Ip Nsfx Abcowh - Used, as seen -

Condition: reconditioned (used), Year of construction: 1974, Universal lead and spindle lathe Make: WEILER Model: Commodor Year of manufacture: 1974 - overhauled newly painted RAL 7035 light gray Mach. no.: 0068 Center height: 180 mm Center width: 1000 mm Spindle bore: 56 mm with guarantee geometric acceptance with test report Accessories: - 3-axis digital display FAGOR Innova 30i-T new - Chuck protection hood with electrical protection Bsdjmgaddspfx Abcjwh - Quick-change tool holder size B - simple bed stop - Coolant device - Operating instructions - used, as seen -

Condition: reconditioned (used), Year of construction: 1990, Universal lead and feed spindle lathe Make: WEILER Model: Praktikum 160 B Year of manufacture: 1990 - overhauled newly painted RAL 7035 light gray Bsdehy Tdyopfx Abcowh Mach. no.: 90-160-2054 Center height: 160 mm Center width: 650 mm geometric acceptance with test report Accessories: - 3-axis digital display FAGOR Innova 30i T - covered lead and feed spindle - braked drive motor - coolant system - electrically secured chuck protection hood - quick-change tool holder size A - simple bed stop - chip back wall - operating instructions with guarantee used as seen The machine is technically corresponding to the state of the year it was built.

Condition: reconditioned (used), Year of construction: 1989, Universal lead and spindle lathe Make: WEILER Model: Condor B Year of manufacture: 1989 - overhauled newly painted RAL 7035 light gray Mach. No.: 1401 with guarantee Accessories: - 3-A digital display FAGOR Innova 30i T, new - Chuck protection hood with electrical fuse, new - Quick-change tool holder base body size B - Bed stop Bwjdpfx Aeg R S Rcjbcjh - Coolant device - Chip back wall - Operating instructions -used, as seen -

Condition: excellent (used), Year of construction: 2006, Centre height: 160 mm Centre distance: 650 mm Spindle speed: 2,500 min-1 Multifix Tailstock Accessories Bwjdpfow Sn Irex Abcoh

Condition: excellent (used), Weiler Ergodor lathe Max. Turning diameter over bed: approx. 320 mm Max. Turning diameter over support: approx. 160 mm Max. Turning length: approx. 470 mm Bar passage: approx. 36 mm Spindle: Speed range: approx. 30 - 3550 rpm Spindle nose: A 2 - 5 Drive power: approx. 3.0 kW Automatic longitudinal & face feeds: Feed range: approx. 0.020 - 2.0 mm/rev Suitable for threads: - metric 0.20 - 12 mm Bwsdpoq Ixxyofx Abcoh Inch 80 - 2 Gg/ Diametral - Pitch thread 160 - 5.5 Dp Module 0.1 - 4

Condition: excellent (used), functionality: fully functional, Provisur Weiler 878 grinder, 50hp model. Greta machine for burger, sausage, Petfood manufacturer. Can mince fresh or frozen flaked meat. Extended hopper. Bwsdpfx Abox Av Rujcjh

Condition: good (used), Year of construction: 1988, Weiler lathe Type Condor B 2-axis digital readout Center height 165 mm Center distance 750 mm Rotation over bed 330 mm Rotation over cross slide 185 mm Spindle bore 40 mm Connected load 3 kw Speed 22-2800 rpm Tailstock MK 3 Coolant pump (not connected) work light Automatic longitudinal and planar feed Bwodpfevgmbvex Abceh spindle brake - Folding jaw chuck guard - splash guard Weight approx. 1040 kg 3 jaw lathe chuck Multifix B Rotating center point

Condition: reconditioned (used), Year of construction: 1977, Engine Lathe Brand: WEILER Model: MDU 260 Year of manufacture: 1977 – workshop tested Machine no.: 14942 Centre height: 125 mm Spindle bore: 28 mm Accessories: - Electrically operated chuck guard - 3-jaw chuck Ø 140 mm Bwjdpfjxv A I Tsx Abcsh incl. set of turning jaws incl. set of boring jaws - 4-jaw chuck Ø 140 mm incl. set of turning jaws incl. set of boring jaws - Safety chuck key - Manual clamping device - Collet set W28 (366E) - Set (25 pcs.) collets W28 (366E) from 1.0-25.0 mm in 1.0 mm steps - Fixed centre for headstock W28 (366E) - Quick-change toolholder Body size A - Operating manual Used as seen, without warranty The machine is technically in accordance with the state of the art of its year of manufacture.

Condition: ready for operation (used), Distance between centers: 500mm, center height: 140mm, turning diameter over bed/cross slide: 295mm/155mm, spindle bore: 36mm, speed: 3550rpm, tailstock taper: MK3. Machine dimensions X/Y/Z: approx. 1500mm/800mm/1250mm, weight: approx. 700kg. On site inspection is possible. Bwjdpfsx Hz Rqex Abceh

Condition: ready for operation (used), A conventional precision lathe Weiler is available. Distance between centers: 650mm, center height: 160mm, swing diameter over bed/faceplate: 320mm/190mm, spindle bore: 43mm, speed: 2500rpm, quill diameter: 40mm, quill travel: 85mm. Machine dimensions X/Y/Z: approx. 1800mm/900mm/1600mm, weight: approx. 1050kg. An on-site inspection is possible. Bodex Hz N Hepfx Abcewh

Condition: ready for operation (used), functionality: fully functional, Weiler Commodor in good working condition. Specifications: Swing diameter over bed: 380 mm Swing diameter over cross slide: 190 mm Distance between centers: 1000 mm Bwsdox Ngpdspfx Abcjh Spindle bore: 56 mm Speed: 25–2000 rpm Motor power: 4 kW Machine equipped with: 3-axis digital readout 3-jaw chuck with multiple jaws Coolant system Multifix quick-change tool post with 4 holders Collet system with collets Bed stop

Year of construction: 1986, condition: used, Weiler Primus lathe year ca.1986, three-jaw chuck , Multifix. Machine in a good condition , By arrangement under power ready for demonstration. Bsdpon Ard Defx Abcswh

Condition: excellent (used), Swing over bed 330 mm Distance between centers 750 mm Spindle speeds 1-4'500 rpm Control: WEILER C3 Misc. accessories Bwsdpfeud Naqox Abcoh MARCELS MASCHINEN CH

Condition: used, Year of construction: 1979, functionality: fully functional, Leadscrew and feed rod lathe Make: WEILER Model: COMMODOR Year: 1979 Bjdpfjxt Ngqsx Abcowh Technical Data Manufacturer: Weiler Model: Commodor Centre distance: 1000 mm Swing over bed: 400 mm Spindle bore: 50 mm Speed range: 63-2000 rpm Drive power: 4 kW Dimensions: approx. L 2.2 x W 1.0 x H 1.7 m Weight: approx. 1.5 t Equipment • 3-axis digital readout • Drill chuck • Röhm 3-jaw chuck, D 200mm • Multifix toolpost • The additional 3-jaw chuck shown on the machine is not included in the scope of delivery! All information without guarantee. A demonstration under power is possible at any time in our showroom.

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and feed screw lathe from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck 160mm with 1 set of jaws >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1 mm to 20 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Fence >> Change wheels To the machine : Bjdpfx Abeu Aftgocswh We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Technical data: >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: Bwsdpfx Asvtp Edebcjh >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection About the machine: A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus GS lead and feed screw lathe 3 axis digital readout Easson- ES8 from training workshop Super condition !!! Technical data: >> Year of construction approx. 1990 Machine no. 3768 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm Bedsvkfhpjpfx Abcswh >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 3-axis digital display from Easson ES8 >> collet chuck device from 1 to 20 mm collets 1 mm rising with holder and draw tube >> 1 three-jaw chuck with 2 sets of jaws >> 1 four-jaw chuck with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Bed stop >> Turning device To the machine : We are offering a Weiler Primus lathe built around 1990 in excellent condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The bed guides are in very good condition. The Weiler runs smoothly even at high speeds. The machine comes from a training workshop of a large company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : Bedpjvivmyjfx Abcewh We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, Weiler precision lathe model Condor B, lead and feed screw lathe with brand new K&C 3-axis digital readout, CE compliant! Technical data: >> Machine No. 2442, year of manufacture 1997 >> Centre height: 165 mm >> Centre distance: 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore: 40 mm >> Camlock spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Thread cutting: metric, imperial, module and diametral pitch threads possible >> Metric thread pitches: 0.18 to 28 mm >> Weight: approx. 1100 kg Bwedpfjxcuazjx Abcsh >> Spindle brake, selectable >> Length: 1.83 m, height: 1.29 m, depth: 0.88 m Equipment and features: >> New K&C 3-axis digital readout, 12-month manufacturer's warranty, supplied with operating manual Features: mm/inch switching, selectable ABS/INC coordinates, value halving function, reference mark, tool memory for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 x brand new 160 mm 3-jaw chuck with 2 sets of jaws >> 1 x 200 mm 4-jaw chuck with 1 set of jaws >> New collet chuck system and new collets from 3 to 25 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear splash guard >> Machine feet Safety features: electronic spindle guard, 2 emergency stop buttons, changewheel box with safety interlock, spindle brake About the machine: Offered here is a Weiler Condor in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new K&C 3-axis digital readout makes work easier and more precise. The machine has been electrically and mechanically checked by us. A complete oil change has been carried out. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to inspect and test this machine under power on site.

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Weiler Primus VC Precision Centre Lathe 3-axis Digital Readout K&C NEW with VC Drive, Stepless Speed Adjustment, and CE Compliance, Very Good Condition Technical Data: Bsdpfx Aow Idllsbcowh >> Year of manufacture: 2003, Machine No. 646 >> Centre height: 140 mm >> Centre distance: 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock Morse taper 3 >> Feeds: from 0.02 to 0.63 mm/rev >> Thread types: Metric, Inch, Module, and Diametral Pitch >> Metric thread pitches: from 0.25 to 8 mm >> Weight: approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and Equipment: >> 3-axis Digital Readout K&C NEW >> Collet chuck system with collets from 3 to 26 mm, new, 1 mm increments, NEW >> 160 mm 3-jaw chuck with 2 sets of jaws >> Multifix size A with 2 toolholders >> Electric chip guard >> Machine feet >> Splash guard About the Machine: This offer is for a Weiler Primus VC lead and feed screw lathe, built in 2003 and in very good original condition. A very nice lathe with VC drive and stepless spindle speed control. The digital readout and scales from K&C are new. This newer generation of Weiler lathes is very user-friendly and can produce ground-like surface finishes. The K&C digital readout makes operation even easier and more precise. Take the opportunity to inspect this machine under power on site and be convinced of its condition.

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Weiler Precision Lathe Model Condor 81 Lead and Feed Spindle Lathe with 3-Axis Digital Display from K&C NEW Technical Data: >> Year of manufacture 1987 Machine No. 87 835 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 Bsdpfjwrmuxjx Abcewh >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: Metric, Inch, Module, and Diametral-Pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis digital display from K&C new, 12 months manufacturer's warranty with operating manual Functions: Switch mm/inch, coordinate selection ABS/INC, halving of display value, reference mark, tool programming 200 pcs, taper calculation, radius/diameter, quick zeroing, reversing of count direction >> 1 piece 3-jaw chuck 160 mm NEW, 2 sets of jaws >> 1 piece 4-jaw chuck 160 mm, 1 set of jaws >> Collet equipment and new collets from 3 to 26 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear panel >> Coolant system >> Machine feet About the Machine: A used Weiler Condor 81 in very good condition is offered. The machine is, of course, fully functional and has been completely disassembled and repainted. A very robust and powerful machine. The new 3-axis digital display from K&C makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was carried out. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine on site under power.

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, Weiler Center Lathe Model Condor B Guide & Feed Shaft Lathe with 3-Axis Digital Readout by K&C NEW from Training Workshop!! Technical Data: >> Machine No. 91-1814, Year of manufacture: 1991 >> Center height: 165 mm >> Distance between centers: 750 mm >> Spindle speeds: from 22 to 2,800 rpm >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet locking >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Threads possible: Metric, Imperial, Module, and Diametral Pitch >> Metric thread leads: from 0.18 to 28 mm >> Weight: approx. 1,100 kg >> Spindle brake switchable >> Dimensions (L x H x D): 1.83 m x 1.29 m x 0.88 m Scope of Delivery and Features: >> NEW 3-axis digital readout from K&C, 12-month manufacturer's warranty with operating manual Functions: mm/inch switch, ABS/INC coordinate selection, display value halving, reference mark, tool programming for 200 items, taper calculation, radius/diameter display, quick zeroing, counting direction reversal >> 1 pc. NEW 160 mm 3-jaw chuck, 2 sets of jaws >> 1 pc. 160 mm 4-jaw chuck, 1 set of jaws >> NEW collet chuck and NEW collets from 2 to 24 mm, incremented by 1 mm >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle safety guard >> Rear splash guard >> Fixed steady rest >> Machine feet Safety features: electronic spindle guard, 2 emergency stop switches, change gear cover with limit switch, spindle brake About the machine: Bsdjw Nw Dqepfx Abcewh We are offering a Weiler Condor in very good condition. The machine is, of course, fully operational. It is a very robust and powerful lathe. The brand new 3-axis digital readout from K&C makes operation even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change has been performed. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine under power at our premises.

Condition: excellent (used), Year of construction: 1983, functionality: fully functional, Weiler Center Lathe Model Condor 81 Lead and Feed Lathe with 3-Axis Digital Readout from K&C NEW Technical Specifications: >> Year of Manufacture 1983 Machine No. 83-067 >> Center height 165 mm >> Center width 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock Bwsdpfxowb Supj Abcsh >> Tailstock MT 3 >> Feed rates from 0.015 to 0.46 mm/rev >> Possible threads: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake can be switched on >> Length 1.83 m, height 1.29 m, depth 0.88 m Accessories and Equipment: >> New 3-axis digital readout from K&C, 12-month manufacturer's warranty with operating instructions Functions: mm/inch switching, ABS/INC coordinate selection, halving of the display value, reference mark, 200 tool programming, cone calculation, radius/diameter, quick zeroing, counting direction switching >> 1 new three-jaw chuck, 160 mm, 2 sets of jaws >> New collet chuck and new collets from 3 to 26 mm, 1 mm increments >> Multifix size B with 3 tool holders >> Electronic spindle protection >> Rear panel >> Coolant system >> Machine feet About the machine: Offered is a used Weiler Condor 81 in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new 3-axis digital readout from K&C makes work even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was also performed. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to view and try out this machine live on-site.