Vertical Turret Lathe - Double Column

RAFAMET KCH- 360/450

Condition: used, swing diameter 2000 mm turning height 1800 mm Control Siemens Sinumerik 840 Dsl turning speeds range 2,8-315 U/min cross rail adjustment - vertical 1200 mm cross rail adjustment - horizontal +/- 1150 mm 1500 mm bit feeder section 240 x 240 mm Minimum immersion diameter 340 mm cutting capacity 50 kN max. torque on the faceplate 50000 Nm speed range step 1 2,8 - 80 U/min speed range step 2 12 - 315 U/min Max. clamping weight 12000 Kg power capacity faceplate 105 kW weight of the machine ca. 33 t dimensions of the machine ca. 10 x 5 x 6,5 m Further technical data: - Feed range of three-phase servo motors: 1–3000 mm/min; 0.01–50 mm/rev - Crossbeam travel speed: 425 mm/min Hnsdpfx Ajy Dvlqsb Ijt Features/Accessories - Increased turning height (+600 mm) - Z-axis extended to 1500 mm - Magazine capacity: 20 positions - Magazine type: disc magazine - Max. tool length: 525 mm - Chip conveyor - Workpiece measurement - Renishaw probe - Coolant tank capacity: approx. 2000 litres - Coolant pump flow rate: 60 litres/min at 2 bar Overhaul: - Extensively overhauled in 2012 by Siemens Industry Munich - Items overhauled included: control system, cabling, motors, measuring systems, etc. - Further information can be found in the PDF

Condition: used, Year of construction: 2010, operating hours: 11,780 h, Equipment: ABS, all wheel drive, Volvo EXCAVATOR EW140C air conditioning 16,850 kg 91 kW Hnodpfx Aoyltr Aeb Ijt Top condition

Condition: reconditioned (used), functionality: fully functional, Year of construction: 1997, sheet thickness steel (max.): 16 mm, cutting length (max.): 4,000 mm, HYDRAULIC SHEAR LVD MVSB 40/16 Serial number 24159 Yom 1997 TECHNICAL SPECIFICATIONS Max. sheet thickness St45 16 mm Cutting length 4050 mm Distance between uprights 4250 mm Range back gauge 1000mm Min. cutting angle 0.5 ° Max. cutting angle 2.0 ° Min. number of strokes/min. 7 Max. number of strokes/min 26 Min. blade clearance 0.5 mm Hsdpfjuipu Eox Ab Ijnt Max. blade clearance 1.6 mm Motor power 22 kW Approx weight 20500 Kg LxWxH 4800x2170x2750mm Accessories included; Electrical adjustment of back gauge 1000mm with Go-to controller blade clearance and cutting angle adjustable. 1 x Front support 1500mm, one with 90° square arm front support 1 x Front support of 1500mm Foot pedal

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg Hnjdpfx Aorgzv Nsb Iet * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Year of construction: 1981, condition: excellent (used), faceplate diam 1300mm max turning diam 1100mm range of turning diam 460-1250mm Hnodpfxok Dz N Io Ab Iot

Year of construction: 1999, condition: good (used), pinch roll unit/felt brake/crop shear for slitting line Hsdpfxjgryl Aj Ab Ijnt strip width: 500 - 1.650 mm strip thickness: 0,4 – 4 mm No. of pinch rolls: 2

Condition: used, Year of construction: 1952, workpiece length 5000 mm swing dia. 1100 mm clamping length 6000 mm grinding diameter 1100 mm grinding wheel diameter 1300 mm workpiece weight 2500 kg main drive motor 22 kW crankshaft bearing diameter 275 mm steady 100-250 mm speeds of tool 400/500 U/min workpiece turning speeds 20-40 U/min weight of the machine ca. 30 t 13 Grinding Steady Rests Mandrels Mounting Flanges Clamping Devices The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. Hjdpfx Ajyt Rxvob Isnt We look forward to your visit. Your Markus Hirsch Team

Condition: ready for operation (used), Year of construction: 2013, This Okuma MCR-A5C30x65 gantry milling machine was manufactured in 2013. It features a robust 100 mm spindle, capable of speeds up to 4000 min⁻¹, and accommodates a maximum workpiece size of 2540 mm by 5540 mm. The machine supports a hefty 30,000 kg on its 2500 × 6300 mm table. Ideal for heavy-duty milling with a rapid feed rate of 20,000 mm/min. Contact us for more information about this machine. Hedpfex D S Eksx Ab Ijnt Machine Benefits Technical Machine Benefits • Dimensions of machine (lxwxh): 2500 mm x 6600 mm x 6350 mm / weight (kg): 59000 kg • Max workpiece width: 2540 mm / max workpiece length: 5540 mm • Table size (width × length): 2500 mm × 6300 mm /max load on table: 30000 kg table height from floor: 850 mm /effective width between columns: 3050 mm/ t-slot (width × number): 24h7 × 13 • Cutting feed rate: 1 to 10000 mm/min/ rapid feed rate: 20000 mm/min/ table movement x-axis: 6500 mm /x-axis travel: 6500 mm /y-axis travel: 3500 mm/ z-axis travel: 650 mm • Tool holder: bt50 + masz type/ tool storage capacity: 50 tools /max tool length: 300 mm • Power supply: 400v, 3 /phases, 50hz rated capacity: 513 kva /full load current: 741 a /peak current: 117/138 a /short circuit current: 18 ka • Spindle diameter: 100 mm /spindle speed: 30 to 4000 min⁻¹ • Large table size suitable for heavy loads. /extensive tool storage capacity. /high rapid feed rate for efficient operations.

Condition: good (used), Year of construction: 1995, roller (top) diameter: 330 mm, sheet thickness (max.): 23 mm, Manufacturer: IMCAR Type: SIHR Year of manufacture: 1995 Extended end for profile bending rolls (Pipe & T-Angle) Central lubrication Digital readout position side rolls Fully hydraulic machine Hydraulic drop end Hardened rolls Specifications Metric US Standard Roll width: 3100 mm Sheet thickness at 3 x top roll Ø: 18 mm Sheet thickness at 5 x top roll Ø: 23 mm Hedpfx Abswpku Do Iont Sheet thickness for initial bending: 20 mm Top roll Ø: 330 mm Side roll Ø: 310 mm Number of rolls: 3 Bending speed: 0 - 5 Side roll adjustment: 200 mm/min. Number of driven rolls: 2 Power: 15 kW Dimensions (estimated) Length: 5250 mm Width: 1700 mm Height: 1700 mm Weight: 11900 kg Please note: The information on this page has been provided to the best of our knowledge, and wherever possible, from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, it does not constitute representation or contractual terms. We recommend you check all critical details.

Condition: good (used), Year of construction: 2014, functionality: fully functional, overall weight: 2,200 kg, KUKA KRC4 linear axis 1500/3T Article number: 8143983 Hnodpfx Abovzxg Tj Iot Serial number: 143983 The KUKA KRC4 linear axis is a high-precision and robust motion unit that is ideal for industrial applications. It ensures precise control of motion sequences and plays a central role in automation processes and robotic systems within production. Its stable construction ensures consistently reliable performance, even in the most demanding applications.