Clamping Units

Rottler

Condition: used, Technical details: vertical rapid adjustment: z-Achse: 1125 mm horizontal adjustment: x-Achse: 600 (+1000 elektrisch-manuell) mm cross adjustment: Frässupport y-Achse: 325 (340) mm control: Siemens 840D diameter of clamping surface: 3500/5800 mm turning diameter: max.6000 mm range of revolution per miute: Planscheibe: 1 - 12 U/min revolution per minute: Frässpindel: 1000-6000 U/min max. workpiece diameter on pallets: 6000 mm workpiece weight: 10 - 2000 kN tool taper: HSK-A-100 total power requirement: 120 kVA weight of the machine ca.: 35,0 t Annular Ring and Cylinder Machining Center Vertical special CNC machining center application: for turning-drilling and milling, grinding of annular parts (large gears, roller slewing rings, gear rims, special flanges, etc.) machine consists of two separate main groups: column unit and face plate/table unit - Feed drives via AC servomotors - cross adjustment milling support z-axis 325 (max.340) mm - Drive power of the faceplate drive 76 kW - Positioning of the table = 0,02mm Djdsu Idlfopfx Adrowa What was renewed: - Axle motors were renewed (Siemens) - Central lubrication for large-diameter antifriction bearings of the turntable/spindle has been extended - partly the machine cabling - bladder accumulator and the safety valve i.D. *

Condition: used, Year of construction: 1993, 1500 mm tank diameter / tank height 1500 / 500 mm Djdpfxjxq Hg Aj Adrswa turning speed range 1500 U/min voltage 380 V volumn 300 Liter power requirement 18 kW weight of the machine ca. 1,2 t dimensions 1,5 x 1,6 x 1,6 m Vibration dryer See ??pictures

Condition: ready for operation (used), Drilling capacity (steel): 100mm, max. pitch circle diameter: 7000mm, spindles: 2, spindle speed: 3000rpm, spindle mount: ISO 50, drill carriage stroke: 900mm, feed: 6m/min, power: 125kW. Machine dimensions X/Y/Z: approx. 13000mm/11000mm/5100mm, weight: approx. 18000kg. On-site inspection is possible. Dedpfx Asvriq Rjdrewa

Condition: used, Year of construction: 2008, Technical details: bore capacity in steel (diameter): 100 mm max. pitch circle: 7000 mm number of spindles: 2 bore spindle turning speed range: 1 - 3000 U/min high speed spindle taper ISO: 50 bore slide stroke: 900 mm feed speeds: 1 - 6000 mm/min max. workpiece weight: 18000 kg total power requirement: 125 kW dimensions of the machine ca.: 13 x 11 x 5,1 m with CNC SIEMENS 840 D Workpiece clamping up to dia. 7000 mm The machine is equipped with 2 drilling spindle supports and through spindle coolant (50 bar)both supports can drill simultaneously. Spindle taper SK 50, 2 stages 1 -600 rpm 1650 Nm and Djdpfjvb Drhex Adrjwa 1 - 3000 rpm. 300 Nm Chip conveyor and coolant device *

Condition: used, Year of construction: 2020, machine/vehicle number: 031EP-2020, Lg.no. 24558 Technical data: - Abrasive diameter 150 mm - Sanding unit swivels on articulated arm - Swivel radius of sanding arm 2000 mm - Motorized dust extraction Dwjdpfxevazz De Adrea - Infinitely variable disc speed - 800 - 2200 rpm - Table dimensions 1500 x 880 mm - table height approx. 920 mm - Drive 400 V / 3.6 kW - Space requirement approx. W 1600 x H 1600 x D 1600 mm - Weight approx. 250 kg

Condition: excellent (used), Year of construction: 2001, turning length: 8,000 mm, turning diameter over bed slide: 2,000 mm, workpiece weight (max.): 25,000 kg, turning diameter over top slide: 1,550 mm, Swing over bed Ø: 2000mm Swing over cross slide Ø:1550mm Dsdjxxxbzjpfx Adrjwa DBC Turning Length: 8000mm Spindle bore: 150mm Spindle power: 95kW Bed width: 1400mm Tailstock spindle Ø: 260Ø Stroke pinole: 200mm Spindle taper: Metric 80Mk Workpiece weight: 25000 Power: 95A Speeds / ranges: 360Rpm Feed rate X-Axis: 0 - 6000mm/min. Feed rate Z-Axis: 0 - 6000mm/min. Length: 16000mm Width: 5000mm Height: 3800mm Weight: 80000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 1996, spindle bore: 160 mm, Swing over bed Ø 1040 mm Swing over cross slide Ø 710 mm Swing in the gap Ø 1580 mm DBC Turning Length Dwjdpfx Adextbf Eorja 3000/4500 mm Gap length 1500 mm Spindle bore 160 mm Spindle power 40 kW Bed width 800 mm Spindle taper 6 Mk Workpiece weight 3500 Speeds / ranges 800 Rpm Feed rate X-Axis 10000 mm/min. Feed rate Z-Axis 10000 mm/min. Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 2019, condition: like new (used), MUT RWO 360/400-1150 Retort Heat Treatment Furnace - Like new: hardly used - Documentation available (both electronic and physical) - Pallet with spare parts included TECHNICAL DATA System type: RWO 360/400-1150 Furnace chamber temperature: ≤ 1150 °C for max. 1 hour Operating temperature: ≤ 1100 °C, ≤ 1050 °C in a vacuum Control stability: ± 2 K Temperature homogeneity: ± 6 K in the range of 600 °C to 1150 °C at the end of the stabilization period Control voltage: 230 VAC / 24 VDC Furnace working space: 360 x 400 mm Dwedpfx Adeiryyaeroa Load: ≤ 50 kg Heating: Three-zone Pressure: ≤ 350 mbar Final vacuum pressure in the cold state: < 5 * 10-5 mbar in a clean, dry furnace Installation area: 900 x 1900 x 3000 mm Total system weight approx.: 1500 kg Sound pressure level: < 70 dB We assume no liability for the accuracy, completeness, and currency of the information provided.

Condition: good (used), These listed powered tools, VDI 50, are designed for a tool changer manufactured by SAUTER and are in good condition and fully functional. They were used on a CNC turning machine, GILDEMEISTER CTX 600. 6 x powered tools, straight design, manufactured by NACKE + WTO, VDI 50 for tool turret manufactured by SAUTER: Item No.: XVI 24275 1 Drilling and milling tool, straight design, manufacturer: NACKE, VDI 50 mm, similar to DIN 69880, No. 40.5040 / 80 96 / 027.1, collet Ø 25 mm, SAUTER drive B 20 x 17 DIN 5482 Price: € 545.00 plus applicable VAT. Item No.: XVI 24277 1 Drilling and milling tool, straight design, manufacturer: NACKE, VDI 50 mm, similar to DIN 69880, No. 40.5040 / 80 96 / 027.3, collet Ø 25 mm, SAUTER drive B 20 x 17 DIN 5482 Price: € 400.00 plus applicable VAT. Item No.: XVI 2687 1 Drilling and milling tool, straight design, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: € 650.00 plus applicable VAT. Dodpfobql S Hex Adrjwa Item No.: XVI 2687 1 Drilling and milling tool, straight design, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: € 650.00 plus applicable VAT. Item No.: XVI 2687 1 Drilling and milling tool, straight design, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: € 650.00 plus applicable VAT. Item No.: XVI 2687 1 Drilling and milling tool, straight design, manufacturer: WTO, VDI 50 mm, similar to DIN 69880, collet Ø 32 mm, SAUTER drive B 20 x 17 DIN 5482 Price: € 650.00 plus applicable VAT. Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Condition: like new (used), Year of construction: 2020, operating hours: 5,500 h, functionality: fully functional, machine/vehicle number: XZHGB50-12050, Equipment: documentation/manual, PLEASE ONLY SERIOUS ENQUIRIES REGARDING VIEWINGS OF THE PRODUCTION LINE! WE DO NOT INTEND TO DISMANTLE THE LINE IN JANUARY; THE ADVERT COULD NOT BE PROGRESSED OTHERWISE. Dwodpfjya Eh Eox Adrsa I am offering for sale a completely unique production line in Hungary. 1. The line manufactures trays suitable for storing 10 eggs, in either continuous or batch operation. From raw material preparation to final delivery, we are offering a complete system for sale. 2. The egg tray production line is located in Bátonyterenye, where a fully serviced industrial site provides all the infrastructure necessary for production. 3. The total output of the line is sold on the domestic market. The complete egg tray production line consists of several units: - Material preparation system, which processes waste paper into mouldable raw material. - HGHY egg tray forming unit, which finalises the trays by drying and hot-air pressing after moulding. - Palletising system, which makes the finished trays ready for transportation. - Auxiliary systems for air, vacuum, power, gas, and water supply.