TUGRA AC-450

TUGRA AC-450

Condition: new, saw blade diameter 370 mm capacity 90 degrees: round 120 mm capacity 90 degrees: square 100 mm 180x100 mm Working height 925 mm saw blade turning speeds 15+30 oder 30+60 U/min total power requirement 1,8/2,2 kW weight of the machine ca. 0,44 t dimensions of the machine ca. 0,8 x 1,1 x 2,1 m SPECIAL PRICE!!! Dljded Iin Iopfx Addja High-performance vertical circular saw Hydropneumatic semi-automatic. (20185/ 20188) · miter left 60° + right 45° · Vice with double clamping arm · Robust prism guide of the saw head, adjustable dovetail guide. · Chip brush · Automatic cooling · Metal tension wheel for high power transmission c. · Solid, strong cast iron table Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the beginning of the material or cut the same for series cutting 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise MPS control: · Save cut start/end · Display of current consumption, number of pieces, cutting time... · Adjustable water cooling · Cutting pressure regulator ATTENTION: Price is without saw blade!!! (saw blade price EUR 204)

Condition: used, machine/vehicle number: 76271002, sheet width:2040 mm plate thickness:1,2 mm Dlsdpfjcxxq Esx Addea total power requirement:2,5 kW weight of the machine ca.:2,0 t dimensions of the machine ca.:3,0 x 1,6 x 1,7 m

Condition: new, Year of construction: 2024, pressure: 8 bar, Miter setting horizontally 15°- 90°15° infinitely variable saw motor 5.50 KW (400 volts) saw blade 600 mm traversing range rear stop 180 mm working height 940 to 1000 mm adjustable via feet 2 x suction nozzles (above in the hood and below) net weight 600 kg WxDxH 135x140x150 cm RAL 9007 gray aluminum rotary plate polished nickel steel Saw head with recirculating ball guides designed with high accuracy and long service life and high rigidity. Sawing material can be preloaded with low pressure when the hood is open. Hydropneumatic sheet feed Chip flow towards the extraction hood. Furnishing • Precision underfloor circular saw • Miter adjustment 0º/ 45º/ 90º/ -45º / -60º continuously • incl. 2 pneumatic vices (vertical) • Infinitely adjustable saw blade feed • Two-hand safety control • Adjustable material stop (rear) • Suction device-swarf extraction system Othgf • Mist spray device for air-oil cooling • Air gun with spiral hose • incl. maintenance unit with pressure reducer • Ergonomically arranged control panel Dlodpfx Adjgwt S Tsdoa • maximum cutting height 230 mm Hxdcvds7y • Saw blade 600mm • Saw blade not included! Our NC pusher system ensures that your machining parts are positioned at the desired machining position on our UK 600 HA 90°. A gripper clamps the material, the NC control positions the material automatically. The tension and the sawing process are then triggered. The positions are previously programmed into the program control. Once the machine tool has completed your machining, it automatically moves to the next sawing position. Depending on the processing part, several parts can also be clamped on top of each other/next to each other and positioned at the same time. It is always possible for you to inspect the desired system in our production/demonstration hall. Please do not hesitate to contact us.

Year of construction: 2025, condition: new, The manual length stop with hand wheel and electronic dimension display MD 100 h is ideal for frequently changing section lengths and for stopping long materials. It enables the carriage to be moved quickly and precisely using a hand crank. Existing machines / roller conveyors can be retrofitted at any time. Product Details: • Suitable for hitting steel profiles and solid materials • Hand wheel drive for the carriage • Pneumatic stop clamping with high holding power Dljdpfeidmp Tex Addsa • digital actual length display in the working area • Direct distance measurement via sensor / magnetic tape • Control with dimensional error compensation • Trolley with 3 ball bearings • raise and lower manual arm • Cable chain with steel storage tray • Standard measurement lengths: 1m to 6m, maximum up to 20m • Total length of the system = measuring length + 0.5 m • Left or right hand versions available • Mounting screws • Accesories: – Stop arm with spring damping – Arm retraction with impact damping via pneumatic cylinder – pneumatic arm raise / lower – Piece counter for the number of pieces/cuts made – various material roller conveyors

Condition: new, Bernardo horizontal bandsaw HBS 275-400 V Technical specifications Cutting capacity round 90 ° and 225 mm Cutting capacity 90 ° 200 x 200 mm square Section flat 90 ° 245 x 150 mm Cutting area around 45° 160 mm Section square 45 ° 160 x 160 mm Cutting area around 60 ° 100 mm Cutting range, square 60 ° 100 x 100 mm Working height 910 mm Band saw blade dimensions 2480 x 27 x 0,9 mm Cutting speeds of 400 V 45 / 90 m / min Coolant pump S1 100% 100 W S1 motor power output 100% 1,1 kW Motor power S6 40% 1,5 kW Voltage 400 V Machine dimensions (L x D x H) 1430 x 720 x 1700 mm Weight approx. 190 kg Dedpod Du T Iefx Addola Scope of delivery • Band saw blade • Workpiece stop • Base • Belt tension gauge • Vise with quick locking • Coolant system • Hydraulic lowering cylinder • Motor protection switch • Automatic shut-off

Year of construction: 1977, condition: refurbished (used), I sell the double mitre saw Rapid DGS, year 1977. Tilting heads Drilling front heads on each side included Very good condition. Available immediately. Dsdod N Rb Dopfx Addsla

Condition: new, saw blade diameter 315/350 mm capacity 90 degrees: round 125 mm capacity 90 degrees: square 110 mm capacity 90 degrees: flat 160x90 mm capacity 45 degrees: round 105 mm capacity 45 degrees: square 90 mm capacity 60 degrees: flat 80x100 mm total power requirement 1,8/2,5 kW weight of the machine ca. 0,2 t dimensions of the machine ca. 0,6 x 1,22 x 1,06 m The large workshop saw with sophisticated technology. (20070) • For miter cuts right and left up to 45°, end stop at 90° and at Dljdpfx Asd Iin Tsddea 45° left • For sawing steel, stainless steel, and, to a limited extent, aluminum profiles • Vice with quick-release lever, longitudinally adjustable clamping jaw, adjustable guide, and double clamping arm for burr-free cuts • Conical safety clutch made of hardened steel to protect the saw blades. • Large base plate made of solid cast iron for maximum stability and low-vibration sawing • 2 speeds: 30 + 60 rpm • Powerful special gear with elastic clutch for heavy-duty use • Automatic cooling directly on the saw blade • Saw head with double bearings • 24 V safety switch in the handle with restart lock • Length stop, assembly tool ATTENTION: Price does not include saw blade!!!

Year of construction: 2025, condition: new, The manual length stop with hand wheel and electronic dimension display MD 50 h is ideal for frequently changing section lengths and for stopping long materials. A hand crank enables the carriage to be moved quickly and precisely. Djdpjidln Tsfx Addela

Condition: new, Year of construction: 2025, Fully automatic cutting of medium-large aluminium profiles with simple-to-use automation. Put down any aluminium profile, the machine will automatically detect it and cut it into jobs tasked with high-accuracy servo motor material positioning. Excel job lists WIFI input for streamlined input of large cutting lists. For every piece of aluminium you place down to cut, no matter what length, a laser sensor measures its length. Our powerful optimisation algorithm on-the-fly calculates the best order of parts to produce minimum waste. The machine automatically cuts the calculated list without stopping. No need for any inputs from you, just keep putting in new aluminium stock. Simple, high-speed alternative to double-headed saws. Just enter (or import) the lengths and angles you need and press GO. The machine continuously produces your angled parts, accurately and at high speed. • Fully-automatic cutting operation with bar feeding and cutting to length. • Simple user interface for automatic operation, enter job and cut in seconds. • Simplified part, batch, or large excel lists job cutting. • Bundled / multi-bar cutting and counting. • Remote WIFI excel job lists input with extensive data mapping capabilities. • Fully adjustable saw cutting and timber feeding rates for maximum process productivity. • Automatic optimiser mode with timber laser length measure and optimisation for minimum waste (optional). • Automatic labels printing for parts using data from the job list (manual label application, optional). • Inline direct-to-material printing with no operator action required (optional). • Bar codes or QR codes printing or scanning for jobs input (optional). • Automated servo positioning of the saw mitre angle up to ±75° (optional). Dledpfx Adof Ekn Isdsa Highly suitable for: • Windows and doors manufacture • Mitered aluminium structures manufacture • Aluminium fabricated structures manufacture • Composites manufacture • Blinds, shades and furniture manufacture • Aluminium retail sales Model: A550 Length: 3 m Linear Unit: ProfiStop Alpha Material Length: 1680 mm Pushing capacity: 20 - 40 kg Software: Optimiser QUALITY AUSTRALIAN-MADE MACHINES.

Condition: new, measuring length bis 5700 mm Tube length 6000 mm numbers of toolholders 7 Rohr Edelstahl dimensions 6,0 x 0,3 x 0,2 m The length measuring system is available for retrofitting existing roller conveyors in lengths from 2 to 6 meters. The running rail made of rectangular tube 60 x 30 x 3. The steel measuring tape is self-adhesive. Dlodpefv Atljfx Addea The magnifying glass with 6x magnification makes it easier to adjust the settings precisely desired length. Danger: This is just the stop system without roller conveyor!