Die change trolley

unbekannt Hub manuell

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Hfedpfxjuz If Nj Ahfjn Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: good (used), Year of construction: 2001, Machine is in good condition. Parts shown by hand not come. Hedpfx Asrpk Rmohfofn Cutting tools not come.

Condition: refurbished (used), functionality: fully functional, overall weight: 3,200 kg, spindle diameter: 6,995 mm, type of input current: three-phase, roll diameter: 210 mm, spindle speed (max.): 20 rpm, spindle speed (min.): 60 rpm, total height: 1,900 mm, total length: 2,700 mm, total width: 1,600 mm, roll width: 175 mm, year of last overhaul: 2026, warranty duration: 12 months, Equipment: documentation/manual, Thread rolling machine ORT RP18 B 2-roll overhauled Hsdevxa Dbspfx Ahfofn See video The machine is in our warehouse in Gussago BS, under power Test run possible Mimu Machine Tools Italy Power (Ton): 18 Number of rollers: 2

Condition: new, Year of construction: 2024, Technical specs CNC – 1100 Control Syntec 21MA-E Drive system YASKAWA servo drive Main motor 7,5/11 Kw Spindle speed till 7000 Rpm Max drilling dept 1000 mm Drilling diameter 3 till 30 mm X stroke 1000 mm Y stroke 800 mm Z stroke 1000 mm cutting feed 0-300 mm/min inner hole accuracy 0.005mm Surface roughness of the hole Ra 3.2um spindle speed 7000 Rpm X servo motor 2.3Kw Y servo motor 3.0 Kw Z servo motor 2.3 Kw oil pump motor 5,5 Kw oil pressure 21 bar Filtration precision 20 um table loade 7000 kg machine weight 10 ton machine power 34 Kw. Hfodsu Nyxwopfx Ahfsn Capacity of cutting oil tank 800L Machine size 4,8 x 3,8 x 2.6 meter Price is EXW (Stock Europe), Include loaded on truck. Transport, installation, commissioning, training, and yearly service contracts are available upon request for an additional fee. Installation and training is always done by our high qualified Service team in 3 locations in Europe. Netherlands, Germany, Romania. Official Seller CNC Top Ten bv Coevorden, Netherlands

Condition: used, Hydr. flat form scissor lift table FLEXLIFT FLUNDER type 1500 / 100 (without hydraulic unit) Year of manufacture 1991 Nominal lifting capacity 1500 kg Lifting capacity (practically tested) 1000 kg (at approx. 350 bar) platform size 2100 x 1400 mm stroke max. 930 mm Overall height - bottom 100 mm (with mounting frame) Overall height - top 1030 mm Hydr. operating pressure 350 bar = lifting force 1000 kg Motor power of hydraulics 1,5 kW mains connection 400 Volt, 50 Hz - mechanical-hydraulic safety limit switches stop the lowering process when the safety bar is actuated - without hydraulic power unit - without electric control length of installation frame 2270 mm width of mounting frame 1580 mm height of mounting frame = height at bottom 100 mm dead weight of lifting table 500 kg good condition Hfodpfxol Nbqcj Ahfon

Condition: used, Gas heated double chamber furnace type: KA_GB 10.14.14/d heating: natural gas usable dimensions per chamber width: 1.000 mm height: 1.400 mm depth: 1.400 mm max. temperature: 550°C working temperature: 250 – 550°C uniformity: ±5 K total connected load: 15 kVA hot gas circulator power: 2 x 5,5 kW (1470 min-1) combustion air blower power: 1 x 1.5 kW (5520 rpm at 95 Hz) Hfsdodyvipopfx Ahfjn burner output: 2 x 100 kW (expandable to max. 2 x 150 kW) number of control groups: 2

Year of construction: 1967, condition: used, machine/vehicle number: 9317, disk of circular saw-Ø: 275 mm cutting area at 90°: 120 x 75 mm cutting area at 45°: 90 x 65 mm rotations of disk: 2000 rpm engine: 380 V, 1,1 kW space needed: 700 x 900 x 1000 mm Hfedpfjb N Eicsx Ahfon

Condition: used, Year of construction: 1996, core drilling diameter max. 25 mm bore depth 1000 mm swing diameter mm total power requirement 25 kW weight of the machine ca. 12,5 t dimensions of the machine ca. m T B T (Germany) CNC-Controlled Horizontal Deep Hole Drilling " Centre " Model BWP 250 Year 1996, but reconditioned mechanically and electrically in 2006 _____ Working range: X Axis, machine column cross 2,000 mm Z Axis, drilling slide horizontal 1,200 mm Drilling depth 1.000 mm Y Axis, drilling slide vertical 1,100 mm Table clamping area 1,200 x 2,000 mm Drilling capacity in solid material, approx. 4 - 25 mm Tool holder taper HSK 50 Spindle speeds 1.260 - 15,000 rpm Feed rates / quickfeed, XYZ, infinitely variable 100 - 10,000/15.000 mm/min. Force rate of feed motors 27 Nm / 1.000 daN Spindle drive steplessly adjustable 7 kW Total electrical load, approx. 30 kW - 400 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features: Hfedpfx Ajt Hw Ayjhfon " Ideal machine for the complete processing of large workpieces like tool a. dies (cooling holes) mould- and dieplates, hydraulicparts etc. by means of deep hole drilling up to 25 x 1.000 mm, face milling up to Ø 60 mm, spiral twist drilling, counterboring and threading up to M 24 x 3 mm. " SIEMENS Continuous Path Control in 4 axes Model 840 D, with process monitoring for coolant pressure, operation data control function, toollife, feed force,Error diagnostics and easy dialogueprogramming directly on the panel, etc. " High Frequency Spindle Make GAMFIOR with stepless speeds " Hydraulically movable drill bush carrier, swivels 90° for holding gun drills (ELB) or picking up regular tools from the tool changer like twist drills, milling tools, taps, etc. " With automatic tool changer made by MIKSCH, Model CTM 40, using a 12-position tool changer, which is mounted on the r.h.side of machine housing, in fixed position, only moving forward and backward for tool changing operation. " Built-on indexing table as B-Axis made by FIBRO Model RTN 400 = 420 x 420 mm, " Extra Rotary Table made by FIBRO with Ø 1.000mm, for indexing 3-144 positions " Built-in coolant device with chip conveyor and various filters. " 2 steady rests. " Completely covered working area with access at the front and at the side. Condition : Very good condition. This is a rare and valuable machine. Under Power Delivery : immediately ex our Stock Payment : Net, after conclusion of contract.

Condition: new, Table dimensions 800 x 800 mm table load 1500 Kg swivelling range 0 - 105 Grad turning speeds 0,15 - 1 U/min height adjustment 672 - 1180 mm hollow spindle diameter mm welding current 500 Ampere max. torque on the faceplate 3000 Nm total power requirement 0,75 kW dimensions of the machine ca. 1560x1120x750 m Characteristics: • Made in EU • Self-locking gear, therefore no leading and trailing at eccentric load • Hydraulic height adjustment allows almost limitless positioning • Electronic quality components from Schneider / Siemens / Delta • Frequency-controlled stepless speed of the turntable • High stability through a heavy and compact design • CE certificate • Very good value for money • Standard version comes with remote control and dual foot pedal • 3 years warranty (see warranty conditions) • Hydraulically height adjustable with locking system (for fall protection) Hjdpfjfv Azpsx Ahfjfn

Condition: excellent (used), Year of construction: 2012, Coordinate measuring machine for inline and prduction use from Mitutoyo in good condition, built 2012, installed 2014 Controller Mitutoyo UC240, Probe Renishaw PH10MQ/TP7, Software Mitutoyo MCOSMOS-1 V3.5 Measuring ranges: X – axis 905 mm Y – axis 1005 mm Z – axis 605 mm Accuracy acc. ISO 10360 MPEE = [2,5 + 3,5L/1000] µm at temperature range 18… 22 °C Base material Steel fixing holes M8 x 1,25 Hfsdeh Nu Uhjpfx Ahfon Scales Mitutoyo Linear Scales Scale Resolution 0,0001 mm DC motores with encoders Guideways linear guides Probe Renishaw PH10MQ with PHC10-2 plus (used) Probe Renishaw TP7 optional with ACR-3 (used) Computer Workstation WIN 10 (used) loading and tranport to be arranged by the customer