Center lathe

Used Harrison V350 Gap Bed Centre Lathe

Condition: good (used), Year of construction: 1956, Heavy lathe, turning machine, lathe, center and feed screw lathe, center and feed screw lathe -Manufacturer: Weisser, lead screw lathe type PF200 -Turning length: 1340 mm Kledpfx Apotzf N Rjdou -Turning Ø over bed: 420 mm -Turning Ø over support: 240 mm -Spindle bore: Ø 41 mm -Spindle speeds: 31.5 - 1400 rpm -Three-jaw chuck: Röhm Ø 250 mm -Accessories: incl., see photos -Tailstock mount: MK4 -Drive motor: 2.5/3.5 kW -Dimensions: 2670/1000/H1230 mm -Weight: 1450 kg

Condition: used, Year of construction: 1990, Universal tool milling machine Make: MACMON Model: M 100 E Year of manufacture: 1990 – workshop tested Machine No.: 1479 Geometrical inspection with test protocol Accessories: - 3-axis digital readout K+C Arbah-M, new - Fixed table 600 x 210 mm (T-slot: 12 mm) Kodex Ada Repfx Apdjlu - Vertical milling head SK 40 with draw thread S 20 x 2 - Coolant system - Operating manual Used as seen, without warranty The machine conforms technically to the state of the art at the year of manufacture.

Condition: used, Year of construction: 2011, cutting diameter 260 mm saw band length 3340 x 27 x 0,9 mm capacity 90 degrees: square 260 mm capacity 90 degrees: flat 380 x 260 mm band speed 37 / 74 m/min sawing motor 1,5 kW weight of the machine ca. 0,62 t dimensions of the machine ca. 1,7 x 1,4 x 1,3 m Miter band saw - Semi-automatic - Double miter - Material detection during lowering - incl. 7 saw blades Klodpfx Apjwkvq Hodju

Year of construction: 1980, condition: good (used), A used very well preserved cycle controlled lathe from Weisser Heilbronn with SIEMENS control. centre distance 2000 mm centre height 295 mm Swing over bed 600 mm Swing over cross slide 260 mm Swing diameter in the bend 800 mm Total length of the crank 375 mm Bed width 450 mm Plan travel X-axis 350 mm Longitudinal travel Z-axis 1850 mm Spindle nose DIN 55022 size 8 Spindle speed Number 18 14 - 1400 rpm spindle bore 71,5 mm Diameter of front bearing 110 mm feed range 0,01 - 40,95 mm/rev rapid traverse 8 m/min Direct current drive 15 kW 400V 50Hz Max. permissible torque at the spindle 2500 Nm Tailstock quill 80 mm quill stroke 250 mm inner taper quill MK 5 Length x width x height Weight of the machine 5500 kg Accessories Tailstock Pneumatic three-jaw chuck with interchangeable jaws 315mm Quick change holder "MULTIFIX "in front of the center size "C Quadruple turret behind the center Tool holder Coolant device Pneumatic steady rest Klsdpfxjgyy I Aj Apdju Technical data and dimensions: Errors excepted. Videoconference via whatsapp possible by appointment

Condition: good (used), Magnetic table 455 x 170 mm digital display Kedpfxotu Il Tj Apdelu water tank Honing device Wet sanding device

Condition: used, Year of construction: 1976, turning diameter over bed 600 mm turning diameter over slide rest 400 mm turning length 1000 mm turning diameter in the gap 850 mm turning speeds 15 - 810 U/min centre height 300 mm spindle bore 56 mm total power requirement 9,0 KW weight of the machine ca. 2,9 t dimensions of the machine ca. 2,8 x 1,45 x 1,65 m Center lathe - Forkardt 3-jaw chuck F 315 - Single-jaw tool post - Steady rest Kledpfx Apjw Tdxcjdju - Live center - Chuck guard, limit switch monitored - Chip tray

Condition: new, Year of construction: 2026, CORMAK HBS275 band saw, equipped with a hydraulic cylinder, a cooling system and an arm swivelling up to 60º, together with blades from renowned German company Röntgen, is used commonly in ironworking, where precision, quality and cutting speed are essential. Horizontal band saw with a swivelling arm for cutting metals, allows for cutting in plane perpendicular to the axis of material cut and at any angle from 0 to 60º. Material for cutting can be fed manually or with any mechanical feeding device, with automatic tool feed. Band guides are equipped with dedicated carbide plates and bearings. This has a huge impact on band guiding, its durability, cut straightness, cutting accuracy and quality. Carbide guiding drastically reduces the wear of the machine and blades. Kedpfx Aeudi Unopdolu Machine's arm made of uniform cast iron as well as a 27 mm wide cutting band are capable of low and high quantity cutting of profiles and other materials. The vice is located in an adjustable bed, equipped with a quick clamp. Blade guides have cemented carbide plates and roller bearings. Its these cemented carbide guides that provide cut precision and straightness. The arm, positioned at an angle of 25º, thus increasing blade durability. To the bottom of the arm a brush wire is attached, ensuring clean and functional brush. Machine's drive is transmitted through a worm drive. A 3-phase motor with 2 cutting speeds and motor thermal protection. This cutting machine also has a strain gauge - a band tension sensor and an automatic switch-off in case the cutting band breaks. Upper part of the base constitutes a tank for flood coolant draining and chips produced during cutting. A cast iron workbench is attached to the base, with a swivel arm and control panel on separate arm. The main cutting move in the cutting process is moving the cutting band and the arm lowering feed. The arm lowering speed (the cutting speed) is adjusted with the hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds to choose from: 37.5 and 75 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Total power 1.5 kW Power supply 400V 50Hz Arm lowering control hydraulic cylinder Band dimensions 2455 x 27 x 0.9 mm Band speed 37.5/75 m/min Vice base height 900 mm Weight 215 kg Angle 0º ø220 260 x 140 200 x 200 45º R ø160 160 x 140 160 x 160 60º R ø100 120 x 100 100 x 100

Condition: excellent (used), Year of construction: 2024, operating hours: 20 h, turning diameter over cross slide: 300 mm, turning length: 1,350 mm, turning diameter: 510 mm, spindle bore: 50 mm, spindle speed (max.): 2,500 rpm, spindle motor power: 7,500 W, rapid traverse Y-axis: 8 m/min, rapid traverse Z-axis: 8 m/min, rotational speed (min.): 2,500 rpm, quill travel distance: 160 mm, quill diameter: 75 mm, quill stroke: 160 mm, swing diameter over cross slide: 300 mm, feed rate X-axis: 2 m/min, feed rate Y-axis: 2 m/min, workpiece weight (max.): 600 kg, turning diameter over top slide: 300 mm, overall weight: 2,700 kg, mount diameter: 40 mm, Equipment: documentation/manual, Style CNC is a company specializing in the manufacture of CNC lathes and milling machines for single-piece or small-batch production. If you operate a tool shop, prototyping center, or provide services with very fast turnaround times, Style is an excellent solution. The intuitive graphical software allows you to create a program directly on the touch screen of the machine in just a few minutes. Klodpfxsw Eum Aj Apdju We currently have a demo machine for sale with a limited number of dry run hours. The machine is sold with a full 12-month warranty, including commissioning and training. In Poland, Style CNC has its own dedicated service branch.

Condition: reconditioned (used), Year of construction: 2008, functionality: fully functional, input voltage: 400 V, travel distance X-axis: 760 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 570 mm, workpiece height (max.): 520 mm, workpiece weight (max.): 300 kg, number of slots in tool magazine: 34, total height: 2,935 mm, total length: 3,600 mm, total width: 3,700 mm, table width: 860 mm, controller model: FANUC, coolant supply: 12 bar, distance table center to spindle nose: 780 mm, spindle motor power: 15 W, rapid traverse Z-axis: 40 m/min, rapid traverse X-axis: 40 m/min, rapid traverse Y-axis: 40 m/min, spindle nose: ISO 40, spindle speed (max.): 10,000 rpm, spindle speed (min.): 80 rpm, table height: 560 mm, table load: 300 kg, tool diameter: 80 mm, tool length: 300 mm, tool weight: 8 g, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Vertical machining center with automatic pallet changer "DOOSAN mod. VC500" with CNC Fanuc 21i-MB Kjdpfju T Hg Tjx Apdelu

Condition: ready for operation (used), Swing diameter over bed/cross slide: 650mm/430mm, distance between centers: 3000mm, bed width: 450mm, max. workpiece weight: 1800kg, spindle speed: 2000rpm, rapid traverse: 8m/min, feed rate: 2m/min, quill diameter: 105mm, quill stroke: 225mm, taper: MK5, tool stations: 8. Machine dimensions X/Y/Z: approx. 5300mm/2300mm/2200mm, weight: approx. 7000kg. Documentation available. An on-site inspection is possible. Kledpfx Asxr Nvcspdou