Chipper / material shredder

WEIMA WLK 800

Condition: excellent (used), Year of construction: 2018, operating hours: 1,192 h, functionality: fully functional, rotor diameter: 260 mm, rotor width: 800 mm, power: 30 kW (40.79 HP), filling opening width: 800 mm, filling opening length: 1,450 mm, working width: 800 mm, Technical data wood and plastic shredder: Manufacturer WEIMA Maschinenbau GmbH Type WLK 800 Year of construction 2018 Operating hours 1,192 hours Drive power 30 kW Speed 90 rpm Rated current 70 A Slow-blow fuse 80 A Hydraulic pressure for horizontal slide 160 bar, load-dependent or pulsed control selectable Rotor type profiled V-rotor Rotor diameter 260 mm Rotor length 800 mm Rotor speed 80 - 125 rpm Number of cutting crowns, concave, 2-row, 42 pieces Cutting crown size 40 x 40 mm Grain size 15 - 80 mm Feed opening 800 x 1450 mm Cutting chamber dimensions 720 x 700 mm Hopper capacity 0.8 m³ Machine dimensions 2,590 x 1,745 x 2,180 mm (l x w x h) PLC control Siemens SIMATIC S7-1200 Screen basket with 30 mm hole size, can be folded downwards Shredder transport weight 2.8 tonnes Machine equipment: Segmented floor 2-sided Free-cutting hopper Electromechanical drive with WEIMA WAP gearbox Hydromechanical starting clutch V-rotor (2-row) Hnsdpfxswrxkle Adwjg Adjustable counter blade for regulating the cutting gap Reversible counter blade Remote bearing for easy maintenance Condition of the shredder: The shredder was only used sporadically for wood and plastic shredding and is in good, ready-to-use condition. The machine is available at short notice. Scope of delivery: 1 Weimar WLK 800 shredder with control cabinet Comments: The documentation (Manual, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2015, condition: new, Hydraulic magnets are supplied with built-in magnet generator, so that only the hydraulic connection is required. ON/OFF switching and demagnetization Hnjdpjc Spglofx Adweg are triggered by hydraulic flow. We have different sizes and capacities in stock NEW and USED

Condition: used, Year of construction: 2018, System: Decanter Type: Flottweg C4E-4/454 Complete dewatering system in container Year of construction: 2018 Sludge throughput: approx. 0-40m3/h Solids capacity: max. 1.2 TS/h Equipment: front double door, side entrance door, fan heater, lighting, sockets, etc. Rotor: max. speed 3650 min-1 Drum diameter: 470 mm System: Container system Interchangeable bridge system for accommodating the downstream system components. Piped and wired ready for operation as a functioning unit. Container system design: Stand construction, clad with sandwich panels and holders for transportation with interchangeable bridge systems. Accessories: FHM preparation station PolyMix 4000SP, measuring equipment, switchgear Feed pump: Seepex BN 52-6LS Discharge conveyor: SS D320 double trough spiral conveyor Dimensions: L 7820mm x W 2500 mm x H 3880 mm Hnedpfeu R Icmex Adwjg Empty weight: 14500 kg Weight in operation: 15000kg Voltage: 400V Power consumption: 142 A Power consumption max.: 70kW Fuse protection: 250 A Frequency: 50 Hz Sludge inlet: DN 100 Centrate drain: DN200 Solids discharge: Spiral conveyor Further information: see photos

Condition: excellent (used), Year of construction: 2019, operating hours: 3,631 h, color: green, total height: 3,400 mm, total length: 6,850 mm, total width: 2,860 mm, mobility: mobile, General Information Hnsdpfx Ajw Eu Aqodwog Year of Manufacture: 2019 Applications: Forestry and Land Management Technical Information Power: 441 kW (600 HP) Number of cylinders: 6 Engine displacement: 18,100 cc Fuel type: Diesel Drive: Track Unladen weight: 26,700 kg Functional CE marking: yes Condition Technical condition: very good Visual condition: very good

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material Hnedpovwlqqefx Adwjg 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Well-maintained horizontal creel. Passage 1000 mm. Stroke 800 mm. Feed electronically adjustable. Hnodounhl Ujpfx Adwsg Clamping carriage approx. 7.5 m long with 5 hydraulic clamping jacks. Can still be inspected in operation.

Year of construction: 2022, operating hours: 0 h, condition: new, Mobile cleaning centrifuge including buffer storage for dirty water, agitator and double membrane compressed air pump. - new machine - numerous other variants and special designs on request Machine type: Process water centrifuge solid-liquid Manufacturer: Eurotec Innovation GmbH Model: ZS21-M EUR Application: vibratory finishing technology, general solid-liquid separation, cooling lubricant processing, wet blasting systems, ... Benefits: - High discharge through acceleration forces acting in the system of over 1800 times the acceleration of gravity - Management of the process water in a circuit, which minimizes operating costs and protects the environment - Saving of expensive additives for the vibratory grinding process (compound) - Economical and efficient separation of solid particles from a mixture - Economical and efficient separation of solid particles from a mixture - Suitable for process liquids up to 70 ° C (optional cooling available) - frequency-controlled motor drive for smooth acceleration and braking of the rotor Are you looking for innovative solutions for surface treatment and process water treatment? We offer a wide range of systems in the field of vibratory grinding, drying and process water technology, which are precisely tailored to your application. From development to production: We deliver all of our products from a single source and everything is "Made in Germany". Hjdpfxof Sqfqe Adwsng ----- Please just contact us, we will be happy to advise you without obligation. ----- The European Commission provides a platform for out-of-court online dispute resolution (OS platform). The offer serves exclusively as an internet presentation of our goods. The contract negotiation comes about by means of telecommunication (email, fax, telephone, news portal), where we first make you a non-binding offer, in which we inform you about our general terms and conditions and the right of withdrawal with imprint before the purchase / contract is concluded.

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 1 h, functionality: fully functional, Compact Shredder typ PYTHON-XL 1600, with 15 KW electricmotor, 400V 50Hz• • Electric motorreductor 15KW, 400V, 3phs, 50Hz 40% MORE torque compare PYTHON 1600 Standard • Opening 1600 x 1000 mm • Main dimensions L 2700 x B 1400 x H 2600mm • Discharge opening 400x 100mm • Height discharge opening ca 1000mm • Electrical control box with INVERTER, main switch, selector switch on / off switch and emergency stop • Easily moved either with forklift or by means of lifting eyes • Weight approx. 2700 kg • Comprehensive machine manual Hjdpfx Asf N Nlgsdwjng • Finishing in RAL 3002 and RAL 7022 • (Subject to technical changes) • CE certified and "Made in Holland"

Condition: new, Year of construction: 2024, Magnetic separator for chip transport line Hedpfxjcqvhws Adweng Pipe magnet with 4 magnetic plates (permanent magnet) Hinged door for easy removal of metal parts Pipe diameter: 180 mm Location: From stock 54634 Bitburg - available immediately -

Condition: reconditioned (used), functionality: fully functional, Rotary shear, twin-shaft shredder, Drive power: 110 kW (2 x 55 kW), Rated current: 210 amps Blade width: 75 mm Hodpfx Aowva Hisdwsng Cutting unit size: length 1600 mm x width 980 mm Quick-change blade system, SEW gearbox, Including hydraulic pusher, hydraulic rated power: 7.5 kW, Control cabinet, Cutting unit overhauled, Dimensions: Length approx. 6150 mm x width approx. 3100 mm x height approx. 3150 mm, Total weight: approx. 17 t