Eccentric Press - Single Column

WEINGARTEN ARP100

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Klsdpfxsu Rwa Ie Adwol Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, Year of construction: 1977, pressure 250 t stroke 40 - 190 mm no. of strokes 40 /min Kljdpevuuaijfx Adwsl throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm table height over floor 800 mm ram surface 1200 x 800 mm ram adjustment 125 mm power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation

Year of construction: 1981, condition: ready for operation (used), There are two identical eccentric presses available, nominal force: 1000kN, stroke speed: 30-85/min, stroke adjustment: 20-125mm, weight: 8t, year of construction machine 1/ 2: 1978/ 1981, with documentation. Ksdpfx Adelc N Rvowell

Condition: good (used), functionality: fully functional, Year of construction: 2012, machine/vehicle number: 778 F 319, Lazer Cutting Kedpfx Adomx Rrlswoll Fabrikat: Prima Power Typ: Palatino 1530 Baujahr: 2012

Year of construction: 1965, condition: used, pressure 150 t throat 550 mm stroke 10 - 140 mm table surface area 1180 x 980 mm no. of strokes 40 Hub/min dayligth 500 mm ram surface 1040 x 800 mm ram adjustment 70 - 150 mm tool shank hole (depth x diameter) 435 x 55 mm required power 15 kW weight of the machine ca. 12 t Kjdocubatspfx Adwoll dimensions of the machine ca. 3 x 1,7 x 3 m - with additional brake - slide weight compensation - motorized slide adjustment - central grease lubrication (manual) - table mounting plate - safe for manual inlay work

Year of construction: 1988, condition: used, machine/vehicle number: 103.071.3156.78192, disk of circular saw-Ø: 400 u. 425 mm Ksdpoz N Amjfx Adwell cutting area at 90° round: 130 mm cutting area at 90° square: 120 x 120 mm cutting area in mitre at 45° round: 130 mm cutting area in mitre at 45° square: 110 x 110 mm cutting speeds: 11 u. 22 m/min forward feed speeds: 670 mm/min cutting length: m. automat. Vorschub bis 1200 mm electrical connection: 380 V, ca. 4 kVA V sawing drive: 1,6/2,5 kW space needed: 1800 x 3800 x 2000 mm weight: ca. 1800 kg

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Klsdpofx Hv Hsfx Adwol Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: ready for operation (used), Year of construction: 1980, Power: 300 to Size of bolster: 1.200 x 850 mm Overhang: 400 mm Width of ram: 1.100 mm Opening in bolster: 400 x 250 mm Daylight: 500 mm Frequency: 32 1/min Stroke: 30 - 140 mm Ram adjustment: 105 mm Weight: app. 19.500kg Kledpfx Ajd A Hbcedwel Other - allowed for 2-Hand safe working - euqipped by safety valve Herion Xsz 20 - Motorized grease lubrication - Pneumatic ram balancing cylinders - Motorized ram adjustment - T-slots in ram - Stand alone control panel - bearing of con rod overhault

Condition: used, Year of construction: 1999, x-axis 6450 mm Klodst H Sn Repfx Adwjl y-axis 400 mm z-axis 380 mm working lenght 6500 mm Number of tools 8 St. tool taper BT30 tool changing time 1,2 sec diameter of tools max. 80 mm turning speeds 6000 U/min Feed speed X = 34 m/min. Feed speed Y+Z = 18 m/min. total power requirement 8,5 kW dimensions 9800 x 3000 x 2400/3300 mm weight 5400 kg *Bar machining center, 3-axis machining of aluminum, plastic, steel and stainless steel profiles*

Condition: new, weight max. 10 t workpiece diameter 100 - 3200 mm drum diameter 300 x 120 mm feed 100 - 1000 mm/min Kedof Ep Dijpfx Adwjll total power requirement 2 x 0,55 kW