Hydraulic plate shears

DURMA ES3006

Condition: good (used), Year of construction: 2006, sheet width 3100 mm plate thickness 6.0 mm thickness at "Niro-steel" 4.0 mm distance between columns 3120 mm down holder 14 Stück cutting angle 1°5 no. of strokes 14 Hub/min control ENC 100 table width 500 mm work height max. 880 mm oil volume 170 ltr. total power requirement 11.0 KW weight 5550 kg range L-W-H 3750 x 1950 x 1650 mm Machine was used for ALU processing no "heavy" sheet metal processing Dwedsycxgmjpfx Apteb good condition (!) new price ~ 32.000 Euro - in checked conditions - machinevideo - ?v=o2LW7L2r7Xs ----- Swing cut guillotine shear with fixed cutting angle * with DURMA ENC 100 NC control unit * manual cutting gap adjustment from the front ----- Equipment: - electro-hydraulic guillotine shears "swing cut" - with DURMA "ENC 100 NC" control unit * Backgauge preselection - X axis * Number of pieces (in automatic mode) * Control panel, front left * Retraction from backgauge on/off * Input of target/actual value procedure with button - NC electro-motorized backgauge (X axis) * on recirculating ball screws * Traversing speed 120 mm/sec. - Manual cutting gap adjustment, from the front - hydraulically acting hold-down device - 1x side stop 1,000 mm - 2x front support arms - Ball rollers in the front support table - Light barrier behind the machine (safety device) - 1x free-moving foot switch - Rear sheet metal chute - Operating instructions

Condition: excellent (used), Year of construction: 2021, operating hours: 140 h, functionality: fully functional, feed length X-axis: 3,050 mm, feed length Y-axis: 1,250 mm, feed length Z-axis: 80 mm, input frequency: 50 Hz, input current: 29 A, working width: 3,050 mm, We offer this very good HOMAG DRILLTEQ V-500 throughfeed drilling machine, year of construction 2021. Working dimension X 3.050 mm Working dimension Y 1.250 mm Working dimension Z 80 mm Number of milling spindles 1 Main motor power 10 kW Rotation speed max 24.000 rpm Tool clamping system HSK-F63 Tool changer positions 4 Vertical drilling spindles 15 Horizontal drilling spindles in X 6 Horizontal drilling spindles in Y 4 Groove saw 90° turnable Vertical working surface Machine table Feed-through technology Special workpiece clamping system clamp gripper Barcode reader Safety device enclosed cabin Control Homag powerTouch, HOMAG POWER CONTROL Software HOMAG WOODWOP 7.2 Conformity marking CE mark Category: Machining centre Type designation: DRILLTEQ V-500 Subtype: OPTIMAT BHX200 Machine number: 0-250-73-7195 Wiring diagram: 0-250-73-7195 Supply voltage: 400Y/230 V Neutral conductor: yes Phases: 3 Frequency: 50 Hz Maximum operating full load current: 29 A Fuse rating: 35 A Control voltage: 24 V If you have any questions or need more information, feel free to send us a message or give us a call. Dodpjylp Slsfx Aptswb

Condition: excellent (used), Year of construction: 2006, Sheetlength: 3100 mm Cutting capacity: 6 mm Backgauge reach: 750 mm Featured with: - 3 Sheetsupports frontside - Access protection backside - Footpedal Motor power: 11 kW Machine LxWxH: 3750 x 2350 x 1850 mm Machine weight: 5500 kg Dwodpen Smtqofx Aptob

Condition: used, Year of construction: 2019, functionality: fully functional, table length: 8,000 mm, table width: 2,540 mm, overall weight: 8,000 kg, sheet thickness steel (max.): 100 mm, cutting length (max.): 8,000 mm, cutting width (max.): 2,540 mm, drill diameter: 40 mm, FICEP TIPO G25LG - CNC PLATE PROCESSING LINE (DRILLING, MILLING, THERMAL CUTTING) | YEAR 2019 The Ficep Tipo G25LG is a CNC plate processing line for combined drilling, milling, tapping and thermal cutting of steel plates in structural steel fabrication. Built in 2019 - a young machine in its class on the used market. All processes run in a single pass on a rigid double-bridge gantry frame. CONDITION & REFURBISHMENT Refurbished and inspected by a certified technician, ready for operation. - The exact scope of reconditioning varies from machine to machine and is disclosed individually upon serious interest. - Viewing possible by arrangement (machine reconditioned - no demonstration under power). FUNCTION & APPLICATION The vertical mono drilling unit with automatic tool changer (ISO 40) performs drilling, milling, tapping, centre-punching and countersinking. The Hypertherm XPR300 plasma torch and the integrated oxy-fuel cutting unit handle thermal cutting - from thin sheet to heavy plate. The line is operated via the Ficep Pegaso CNC control. Infeed and outfeed roller conveyors with material transfer (8 m each) ensure continuous material flow. Typical applications: structural steel fabrication, steel trading and plant engineering. TECHNICAL DATA - Manufacturer: Ficep | Model: Tipo G25LG | Year: 2019 | Serial number: 36098 - Machine type: CNC plate processing line (drilling / milling / thermal cutting) - Condition: used, refurbished by certified technician Dodpfx Apeu Dw I Ejtjwb - Frame design: double-bridge gantry frame, welded | Machine weight: 8,000 kg - Plate width: max. approx. 2,540 mm, min. 200 mm - Plate thickness: max. 45 mm (plasma cutting), max. 100 mm (drilling) - Drilling heads: 1 (vertical mono drilling unit) | Tool holder: ISO 40 - Max. drilling diameter: 40 mm | Max. drilling/milling depth: 100 mm - Max. spindle speed: 7,000 rpm | Spindle power: 15 kW - Plasma cutting torch (straight): 1 | Plasma source: Hypertherm XPR300 | 300 A - Oxy-fuel cutting unit: included - CNC control: Ficep Pegaso CNC - Processes: drilling, milling (incl. straight/curved slots, Y/J weld-edge preparation), tapping, centre-punching, countersinking, marking, scribing, straight plasma cutting, oxy-fuel cutting On request (to be confirmed bindingly during inspection): processing length, tool magazine stations, min. plate thickness for drilling, min. drilling diameter, pass line height, longitudinal and cross positioning speeds, connected load and machine dimensions. SCOPE OF DELIVERY - 1 x Ficep Tipo G25LG CNC drilling, milling and thermal cutting line (year 2019) - 1 x Ficep Pegaso CNC control - 1 x Vertical mono drilling unit with automatic tool changer (ISO 40) - 1 x Plasma cutting torch (straight) | 1 x Hypertherm XPR300 plasma source (300 A) - 1 x Oxy-fuel cutting unit - 1 x Infeed roller conveyor with material transfer (8 m) | 1 x Outfeed roller conveyor (8 m) - 1 x Extraction system for plasma cutting LOGISTICS & LOCATION Location: Ulft (Netherlands), directly at the German border. Dismantling, transport, installation and commissioning by ASM by arrangement - individually calculated upon request. ABOUT ASM Arendsen Steel Machinery (ASM): specialist for refurbished Ficep structural-steel machinery. Further machines on request. CONTACT / INQUIRY Viewing by arrangement | Price on request. Sale exclusively to commercial customers (B2B).

Year of construction: 2009, condition: like new (used), Press with container Engine 5,5 kW 400 V Dedpfx Aofhb Tijptewb

Condition: ready for operation (used), Slideway grinding machine SFBZ 1800x4000 Length of grinding max, mm 4000 Width of grinding max, mm 1800 Dstance between column mm 2200 Height of grinding max, mm 1250 Table size, mm 4000 x 1800 Grinder wheel size max, mm 630 x 100 x 305 Weight of workpiece max, kg 15000 Dwodpfouug A Eox Aptjb Weight of machine, kg 56.000

Condition: good (used), Year of construction: 2011, machine/vehicle number: 2212.287, Automatic panelsaw Schelling Typ:FH 6 430 Maskin nr:221.287 År:2011 Panel beam saw Schelling with automatic, rear-feed,lifting table. For sawing board material, chipboard, MDF, Plywood, Board, Laminate etc. Techn info: Software MCS Evolution 2.0, SPS, Soft-SPS-Siemens WinAC Operating system WINDOWS XP PC with keyboard and mouse TFT monitor 17" Cutting length 4300mm, automatic detection of the start of the plate Cutting width 4300mm Machine accuracy of the cut length 3m +-0.1mm Positioning accuracy measured at input +-0.1mm Max diameter saw blade 460mm, spindle 30mm Pre-scoring blade 200mm, spindle 20mm motor operation is set from the control console Max panel thickness 120mm Panel stack aligner Main saw blade motor 27kw Saw blade over table 135mm Safety curtain Air cushion table with 3pcs air ball nozzles, radial ventilator fan Table sizes 2650x850mm 620x850mm 2650x2550mm Pressure beam with automatic adjustment of pressure to cut length and package height Package straightener before and after the pressure beam Max package height 120mm (incl. sum of curvature and board thickness tolerance) Pusher with 12 grippers Max clamp opening (gripper) 133mm Min-max force package straightener 400/2000N Speed saw carriage forward 6-150m/min Speed saw carriage back 150m/min Forward feed speed (pusher) up to 25m/min (according to EC Europa EN1870-13) other countries 80m/min Speed feeding back up to 80m/min Push-off device 3 pcs Lift table length x width 4350x2550mm Hydraulic unit Standard version 1600mm lifting height 1.25/2.5m/min raising speed, 1.25/5m/min lowering speed Maximum load 1200 kg/m2 total 9 tons Roller track driven rollers, frequency controlled for stack on lifting table 4100x2600mm Max stack weight 6500 kg Max stack length 1060mm Slots for forklift 4 pcs, distance in the middle 1200mm, slot width 300mm Light curtain for personal protection Roller conveyor driven for package frequency controlled input to lifting table left 5600x2600mm max load 6500kg Roller conveyor driven for packages frequency controlled input to lifting table right 5600x2600mm max load 6500kg Slots for forklift 2 pcs, center distance 900mm, slot width 400mm 2 positioning stops with roller for stack alignment Light curtain (double beam) for personal protection Roller table after saw depth 4300mm, free-running ployamide rollers Angle stop at the rolling table Infeed guide two-lane (beam length 7200mm) 2-sided hardened precision guides rack and pinion drive, two-sided Dwedotk It Sjpfx Aptsb Input carriage (pusher) gear rack servo drive, non-contact measuring system Gripper, (scissor clamps) in pusher 12 pcs Automatic adaptation of the clamping force to the package height (progressive clamping force) can be set to 0 Pusher for panels thickness greater than 6mm,material thinner than 6mm is fed manually Central cleaning system feed trough (pusher) Compressed air 6-8 bar, approx. 1600l/min Power 38 kw, 70 A. 3x400 volts, 50 Hz, operating voltage 24 VDC Dust extraction 4000m/h, air speed 30m/s Diameter connection 80mm (angle connection), 120mm /pressure beam), 150mm (sawdust channel) Total setup area without driven roller conveyors including protective grid approx: 11650x7300mm Driven roller tracks left-right 5500+5500mm Stock no: 2002125BXACEO Subject to incorrect technical data presented

Year of construction: 2010, condition: good (used), USED CNC BIESSE BREMA EKO 902 INSERTING MACHINE TECHNICAL DETAILS: 3-AXIS (X-Y-Z) CNC MACHINING CENTER Djdpohknbrjfx Aptswb - Complete protection of the machining head and the work area on the machine. - Numerical control system with BIESSE Works software on Windows. - Vertical positioning of the panels, with 2 panel clamping jaws. - Panel feed (in the direction of the X-axis, on the lower support with rubber wheels), movement (in the X-axis) of the panel/board clamping jaws. PANEL DIMENSIONS (WORKING DIMENSIONS): - Minimum length: 160 mm / Maximum length: 3200 mm - Minimum width: 35 mm / Maximum width: 900 mm - Minimum thickness: 8 mm / Maximum thickness: 80 mm WORKING GROUPS: - No. 1 Vertical spindle (electro-spindle) ER32 (4.5 kW) with inverter (up to 18000 RPM) - No. 1 Circular saw (for grooves) diameter 120 mm (X-axis fixed) - No. 13 Independent vertical spindles for drilling (6 on the X-axis + 7 on the Y-axis) - No. 8 Independent horizontal spindles for drilling (3+3 on the X-axis and 1+1 on the Y-axis) - No. 1 Head group for hinge drilling - Total installed power: 20 kW AUTOMATIC DOWEL INSERTING GROUP ON BOTH SIDES WITH A PRESSURE PUMP FOR APPLYING THE GLUE.

Condition: used, Year of construction: 2019, functionality: fully functional, machine/vehicle number: AN2018080, total length: 12,860 mm, total width: 4,806 mm, type of input current: three-phase, input voltage: 400 V, feed length X-axis: 3,000 mm, working width: 350 mm, power: 25 kW (33.99 HP), TRC 1500 – Timber Repair & Cosmetic Machine Technical Description • System Overview • Process Workflow System Overview The Wintersteiger TRC 1500 is a fully automated industrial system designed to detect, repair defects in wooden boards. It combines advanced 3D scanning, high-pressure thermoplastic injection technology to deliver consistent, high-quality repairs at production speed. Defects are repaired with thermoplastic filling material using injection and application units. No filling material is wasted thanks to the precise calculation of the filling quantity and precision injection. the edges can also be filled. Key Features • Automated 3D laser triangulation defect detection • High-pressure thermoplastic injection for durable repairs • Precision finishing unit for cosmetic perfection Dedpfex Dmdhex Aptjwb • Independent melt temperature zones with 8 kg tank • Closed glycol-water cooling system for controlled solidification • Ethernet-based control system with remote maintenance • Unlimited product profiles and intuitive scanner interface Product Range (Workpiece Specifications) Length 500–3000 mm Width 100–350 mm Thickness 3–30 mm Production speed upto 10 m/min – depending on number and sizes of defects Filling System – Injection & Application Units • Injection Unit: • 3-axis positioning (X/Y servo-driven, Z pneumatic) • Pressure-regulated melt feed • High-pressure injection • Application Unit: • 3-axis control • Fine finishing of repaired areas Faulty Spot Eye Scanner • 3D laser triangulation and high-speed camera system. • Detects defects from approx. 1 mm depth • Automatic height adjustment • 2D + 3D measurement • Adjustable parameters for wood types Melting Unit • 8 kg tank • Independent temperature zones • Integrated piston pump for constant pressure Cooling Unit • Closed glycol-water circuit • Stable temperature control Control System • Ethernet-based communication with remote maintenance • Access to PLC, scanner, servo drives • Energy-efficient regenerative drive technology Scanner Software • Processes 3D light-section profiles • Calculates defect volume and coordinates • Unlimited product programs • Intuitive operator interface High-Pressure Injection Process 1. Melting of thermoplastic material 2. Pressure and temperature regulation 3. Targeted injection into defect 4. Immediate cooling 5. Minimal surface residue • Benefits: • Low material usage • Excellent adhesion • No alteration of surrounding wood structure System Architecture • Melting unit • Heated hoses • Injection head • Cooling plate • Cooling unit with supply/return flow

Condition: used, Year of construction: 2008, operating hours: 9,950 h, functionality: fully functional, type of input current: three-phase, Handfeed station – 14 x feeder - 12 Clamp Binding Unit - Milling & Spine Preparation Units - Hot Melt Side Glue with pre-melter – Hot Melt Spine Glue with pre-melter - Drum Cover Feeder - Nipping & Pressing Station - Exit Raceway & Laydown Delivery - Conveyor System with Reject Gate - Muller Martini Esprit Trimmer Binding thickness 2 mm - 50 mm Dsdpfx Aextau Esptswb Cover size max. 640 mm Cover size min. 202 mm Max. speed 900 to 4,000 cycles/hr. Max. book size 380x320 mm Min. book size 120x100 mm