Eccentric press

EBU , Typ E 50

Condition: used, Year of construction: 1977, pressure 250 t stroke 40 - 190 mm no. of strokes 40 /min throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm table height over floor 800 mm ram surface 1200 x 800 mm ram adjustment 125 mm power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation Ksdpfx Adjvuuaijwjwt

Condition: excellent (used), Year of construction: 2010, Control: Siemens Sinumerik 840D Work Area Swing diameter over bed: 820 mm Swing diameter over cross slide: 520 mm Cross slide travel: 600 mm Kjdpfx Adoxgdfbowowt Tool Holder: Front: Capto size C6 – Multifix D1 Rear: Boring block with clamping claw Centre Distance: 3,000 mm Main Spindle Drive Power digital AC motor – 60% duty cycle: 46 kW Number of gear stages: 2 (ZF planetary gearbox, electrically shifted, mounted outside the headstock) Headstock Spindle nose DIN 55027 / Bore (standard): 11 / Ø 132 mm Spindle diameter in front bearing: 190 mm Speed range (constant V): 1 – 1800 rpm Standard chuck sizes: Ø 315, Ø 400, Ø 500 mm Spindle nose DIN 55026 / Bore (option): A 11 / Ø 164 mm Spindle diameter in front bearing: 210 mm Speed range (constant V): 1–1600 rpm Cross Slide Transverse feed range: 0.001 – 1000 mm/min Longitudinal feed range: 0.001 – 2000 mm/min Thread pitches: 0.01–999.999 mm Rapid traverse transverse/longitudinal: 5/10 m/min At centre distance: 4,000 mm Transverse feed force: 16,000 N Longitudinal feed force: 22,000 N Turning tool section: 40 x 40 mm² Tailstock Quill diameter: 125 mm Quill travel: 280 mm Taper: 6 Mk Electrical Equipment Three-phase: 400 V, 50 Hz Design in accordance with VDE and EMC guidelines EN50081-2 / EN 50082-2 Interference suppression level A according to EN 50081-2 For TN-S or TN-C networks / industrial networks without RCD protection Dimensions Machine (L × W × H) = 2.88 m + centre distance × 2.55 m × 2.32 m Machine Weight (Centre distance / weight approx. kg) 3000 mm: 10,900 kg

Condition: excellent (used), Grinding length 1000 mm grinding diameter fi 350 mm Kwodsk Abxxepfx Adwjt In very good condition.

Year of construction: 1965, condition: used, pressure 150 t throat 550 mm stroke 10 - 140 mm table surface area 1180 x 980 mm no. of strokes 40 Hub/min dayligth 500 mm ram surface 1040 x 800 mm ram adjustment 70 - 150 mm tool shank hole (depth x diameter) 435 x 55 mm required power 15 kW Kwedpfx Aecubatsdwjt weight of the machine ca. 12 t dimensions of the machine ca. 3 x 1,7 x 3 m - with additional brake - slide weight compensation - motorized slide adjustment - central grease lubrication (manual) - table mounting plate - safe for manual inlay work

Condition: new, Bernardo universal lathe Titan 660 x 2000 Technical Specifications Centre distance 2000 mm Centre height 330 mm Swing diameter over bed 660 mm Swing diameter over cranking 900 mm Swing diameter over cross slide 460 mm Bed width 400 mm Spindle bore 105 mm Spindle mounting DIN 55029, D1-8 Speed range (16) 25 - 1600 rpm Range of longitudinal feeds (25) 0.044 - 1.48 mm/U Plan feed range (25) 0.022 - 0.740 mm/U Metric threads (54) 0.45 - 120 mm inch thread (54) 7/16 - 80 Gg/1″ Pinol diameter 90 mm Kjdpefbbx Refx Adwowt Sleeve travel 235 mm Sleeve holder MK 5 Engine power 7,5 kW (10,0 PS) Machine dimensions (W x D x H) 3630 x 1200 x 1520 mm Weight approx. 2900 kg Features & Benefits Versatile application possibilities in general mechanical engineering, production, single part production, ... Central, handy switch for feeds and threads with guide and feed spindle Prism bed made of grey cast iron, inductively hardened and precision ground Modern main spindle bearings with angular contact roller bearings in precision design Hardened and ground gears and shafts, also in the feed gear Rapid traverse lengthwise and flat as standard to reduce non-productive times Large spindle bore (105 mm) for large diameter workpieces Soft start due to the mechanical multi-disc clutch Electromechanical foot brake to reduce non-productive time Best cutting performance even during face turning For stiffening the bed guide and for minimizing

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm Kwjdpfx Adsfx Hv Hewst dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: ready for operation (used), Year of construction: 1980, Power: 300 to Size of bolster: 1.200 x 850 mm Overhang: 400 mm Width of ram: 1.100 mm Opening in bolster: 400 x 250 mm Daylight: 500 mm Frequency: 32 1/min Stroke: 30 - 140 mm Ram adjustment: 105 mm Weight: app. 19.500kg Other - allowed for 2-Hand safe working Ksdpfx Adjd A Hbcowjwt - euqipped by safety valve Herion Xsz 20 - Motorized grease lubrication - Pneumatic ram balancing cylinders - Motorized ram adjustment - T-slots in ram - Stand alone control panel - bearing of con rod overhault

Condition: used, Year of construction: 1974, turning diameter over bed slide: 480 mm, center width: 1,500 mm, Center Lathe Manufactured by Heidenreich & Harbeck Type Hanseat 480 Fully overhauled in 2012 Technical Specifications Manufactured by Heidenreich & Harbeck Type: Hanseat 480 Year of construction: 1974, fully overhauled in 2012 Control: Conventional Center distance: 1500 mm Turning diameter over bed: 480 mm Turning diameter over support: 295 mm Spindle speed: 20 – 2190 rpm Kwjdpfx Aswm D Iledwst Dimensions: L 3.50 x W 1.20 x H 1.55 m Machine weight: 1200 kg Equipment - 3-jaw chuck D 250, built-in - Faceplate D 400 - 10 quick-change tool holders - 1 steady rest All information is provided without guarantee. A live demonstration is possible at any time in our exhibition hall.

Year of construction: 1995, condition: ready for operation (used), A Promecam (Amada) APX 103 CNC press brake is available. Pressing force: 1000kN, working width: 3000mm, column distance: 2550mm, gap opening: 370mm, stroke: 100mm, column depth: 400mm, infeed speed: 70mm/s, bending speed: 9mm/s, return speed: 85mm/s, drive power: 10.5kW. Machine dimensions X/Y/Z: approx. 3500mm/2200mm/2300mm, weight: approx. 6400kg, control: Amada Operator, operating hours: 36261h. The press is still in operation, therefore the operating hours change continuously. Documentation available. On-site inspection is possible. Kodpfxowm Nn Rs Adwewt

Condition: like new (used), Year of construction: 2021, operating hours: 1,200 h, functionality: fully functional, turning diameter: 1,100 mm, power: 46 kW (62.54 HP), distance between centers: 2,000 mm, load hours: 1,200 h, A DMT CD1100 lathe with Heidenhain control and only 1,200 operating hours is available. The working area offers a swing diameter of approx. 1,100 mm over the bed and approx. 800 mm over the cross-slide. The tool holder is a Multifix D1. The distance between centers is 2,000 mm. The main spindle drive is a motor with 46 kW output at 60% duty cycle and two gearbox stages. Kwjdpoxlza Hofx Adwst Tailstock: - Quill diameter: 125 mm - Taper: 6 Morse taper Delivery: Collection by the buyer Payment: 100% via bank transfer immediately upon invoicing, prior to collection All information is non-binding. Subject to prior sale. The machine is sold without any guarantee or warranty claims and remains our property until full payment is received.