Low loader semitrailer

GOLDHOFER 3-Achs-Tiefbett 3x12 t

Condition: used, maximum load weight: 45,400 kg, overall weight: 66,000 kg, axle configuration: 3 axles, first registration: 08/2012, next inspection (TÜV): 08/2026, total width: 2,750 mm, Equipment: ABS, More vehicles under Extract from equipment. Complete equipment details upon request. * BPW axles, all axles hydraulically steered * Tyres 245/70 R 17.5 * Stake pockets, lashing rings * Removable loading bolster * Aluminium inlay floors * Hydraulic axle compensation * 2-inch king pin * ABS * Tractor unit with hydraulics required * Auxiliary steering * Detachable gooseneck * Folding extensions Lodpjx E Iw Ujfx Aanjak * Small ramps at the front of the loading area * Side walls on the gooseneck * New TÜV inspection available on request

Condition: new, Year of construction: 2023, Standby power 20 kVA (16 kW) Full load 17.5kVA (14kW) Voltage 230/400V Generator power 16 kW Generator continuous power 14 kW Number of phases 3 ECU adjustment Fuel tank capacity 60 l Liquid cooling Frequency 50Hz Rotation speed 1500 rpm. Engine type in-line, 4-cylinder, naturally aspirated Cylinder diameter and length 98 x 105 mm Lasdpfx Aei Nthqsanjk Engine capacity 3.2 liters Capacity oil approx. 3 l (between the min./max. value on the dipstick) Capacity coolant approx. 5 l diesel fuel Compression ratio 17.2:1 DATAKOM D300 control panel Insulation class (alternator) H Number of windings (alternator) 12 IP degree of protection (alternator) IP23 Shunt excitation type Voltage (alternator) +/- 1% Overall dimensions (length x width x height) 2000 x 900 x 1070 mm EURO III emission standard Weight 730 kg

Condition: used, mileage: 53,318 km, lifting height: 1,10,000 mm, Year of construction: 2018, Drivetrain Drive: Wheel Weights Empty weight: 60.000 kg Functional Lifting capacity: 250.000 kg Lodjwz Ut Ispfx Aanoak Identification Serial number: 088666 Other information Front tyres / undercarriage remaining: 90 Rear tyres remaining : 90 Tyre brand: - Carrier engine: - Upper engine: - Counterweight: 0 Transport dimensions (LxWxH): 15.86x2.99x3.99 Additional information Please contact PFEIFER GROUP for more information

Condition: ready for operation (used), Percussion Mill MFL Brand: MFL Lodpfokwzp Tox Aansak Type: RCL 140-160 Feed Opening : 1700 x 1000 mm Driving: E-Motor 250-300 kW.

Condition: as good as new (ex-display), Year of construction: 2024, Set of shredding shafts manufactured NEW. These shafts are available with different knife configurations, the following are currently possible: Size 450 / 650 / 750 / 850 / 950 5 / 6 / 7 / 8 / 9 / 10 knives possible 7 / 8 / 9 disks arivable for machine type VB-750 / VZ-750 / U-75 / HPS-1.5 / Pronar 2.8 / Inmpaktor 250 .. 300 / Titan ... We are also happy to meet your wishes. Ledpfx Asivpkyoanjak Please state your company address and contact details when making enquiries. This way we can prepare a quote and send it to your personal email.

Condition: used, axle configuration: 3 axles, first registration: 03/2007, total width: 2,740 mm, suspension: hydraulics, tire size: 245/70R17.5, wheelbase: 14,380 mm, color: blue, Year of construction: 2007, Nooteboom EURO-54-03 Operates on 24V supplied by the tractor. Remote steering via cable. SAF axles. Extendable by 550 cm. Wheelbase: 1438 - 1988 cm. Total length: 1633 - 2138 cm. Coupling to rear of trailer: 1528 - 2078 cm. Loading platform length: 750 cm + 550 cm extension. Width: 274 cm + wider. Loading height: approx. 48 cm. = Additional Information = Axle configuration Lajdpfeuydmmex Aansk Tyre size: 245/70R17.5 Brakes: drum brakes Suspension: hydraulic suspension Front axle: twin tyres; steered; tyre tread depth left inner: 40%, left outer: 40%, right inner: 40%, right outer: 40% Middle axle: twin tyres; steered; tyre tread depth left inner: 40%, left outer: 40%, right inner: 40%, right outer: 40% Rear axle: twin tyres; steered; tyre tread depth left inner: 40%, left outer: 40%, right inner: 40%, right outer: 40% Weights Unladen weight: 16,720 kg Payload: 34,280 kg Gross vehicle weight (GVW): 51,000 kg Identification Type number: EURO-54-03 / REMOVABLE NECK / 55 = Company Information = ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-GB), Wouter Greutink (NL-DE-GB-ES-IT). Russian spoken. We strive to provide accurate information, but no rights can be derived from the texts provided.

Condition: used, machine/vehicle number: YV2RT60FXKA84xxxx, mileage: 5,874 km, Year of construction: 2021, Please contact ATS Norway for more information Please provide reference number upon request: 20511 Specifications: - 2021 model Lajdpfx Aajwphixjnok - 5874 km (will increase slightly) - Eu-approved until: 21.02.26 - Euro 6 engine - 8x2 - 551 Hp - Suspension on 1st and 2nd axle: Steel - Suspension on 3rd and 4th axle: air - 2 x 110 liter variable pumps - 2 x manual extensions for main boom and 2 x for jib - Scanreco optical remote control (Top model) - Weight cell main boom - Extra function for main boom and jib - Auto leveling (The car puts itself in a level position ready for lifting.) - Virtual room (Possibility to limit all axes with a few keystrokes, no need to go to a workshop for this. Brilliant when working under high voltage etc.) - SKF central lubrication of the crown and up to the first joint - Extra function fully extended on jib - Single winch hook (Jib / main boom) - 2-part winch hook (Jib / main boom) - 4-part winch hook (Main boom) - Hook for jib - Hook for main boom (Large hook) - Emergency lowering unit (24 volts) - Wire stop sensor and sleeve - 4 ton winch - Diagnostic cable for online help (Remote help) - Danfoss valve center - 2 x 2 ton counterweight (Must only be used for cranes above the cabin otherwise the counterweights are not needed, and these can be removed as needed) - Front support leg Construction: - 4 x work lights strategically placed inside each support leg cabinet. - 50" LED bar work light rearward on the cabin - Powerful LED lamps in the crane. - VBG mount, with air servo control unit mounted in the rear cabinet left side. - Bracket on the roof - 2 pcs high beam LED bar on the roof forward (daylight!!). - Orange work warning LED beam on the roof. - EasyUp foldable ladder in the side with railing. - Boxes for chain, chainsaw etc. Mounted on the rear support leg so that these are driven out together with the support leg and are at the same time packed away while driving. - Charger for control in the cabin - Plastic internal screens axle 3 and 4. - 3 edge pull-out cabinet between axle 3 and 4 - On the left side between axle 2 and 3 there is a large cabinet with 500 W fan heater installed to hang clothes to dry etc. - Plane / bottom at the rear closed with alloxed aluminum floor plates that are cut to fit the car perfectly, with rounded edges for a very professional send. - CNC manufactured plates up the rear edge of the cabin. - Fully painted sides, cabin and stern. - Resting cradle for crane for driving without jib. - 5 support leg plates. 4 pcs 80x80x6 cm. placed in dedicated cradles at the rear on the "level" - Right side large cabinet 1.2 x 1 meter - Powerful LED back / work lights at the rear. - Rear part of the car rebuilt with CNC manufactured plates, and beautiful LED taillights have been installed in several stages. - Hatches strategically placed for access to relevant devices under the bodywork. - Precisely cut out fields in the side coverage for access to the screen, manual controls, emergency lowering functions etc. - Marker lights along the side mounted so that they flash together with the turn signals / direction indicators - Cradle to hold the jib when not in use. - Hydraulic extra function dismantled main boom and jib, but mounted if desired. - Kettle...

Condition: new, Year of construction: 2023, functionality: fully functional, overall weight: 915 kg, fuel type: diesel, tank capacity: 70 l, color: beige, power: 27.21 kW (37.00 HP), output current: 47 A, output voltage: 400 V, output frequency: 50 Hz, type of output current: three-phase, nominal power: 26 kW (35.35 HP), nominal power (apparent): 33 kVA, continuous power: 24 kW (32.63 HP), continuous power (apparent): 30 kVA, total length: 2,100 mm, total width: 960 mm, total height: 1,500 mm, rotational speed (max.): 1,500 rpm, motor manufacturer: John Deere, type of cooling: water, AVS-Dieselstromaggregat DW 30 JD2 15 AK14A PRP-Power: 24 kW / 30 kVA ESP-Power: 26.4 kW / 33 kVA Engine: John Deere 3029DFG20 Emission Stage: 2 Speed: 1,500 rpm Mechanical speed governor Operating voltage: 12 V Cooling: water-cooled Generator: Mecc Alte ECP 28-VL/4 C Voltage: 400/231 V Voltage regulator: DSR Control panel: DSE 6120 Battery charger: 5 ampere Type: Canopied aggregate; weather-protected, soundproofed • Emergency stop switch • Radiator with mechanical fan • Base frame construction with integrated fuel tank (70 L) and vibration dampers • Coolant preheater • Voltage and frequency regulation as per ISO 8528-5 • Unit suitable only for stationary use Laodpjwu D Nlofx Aanjk Please note that, according to applicable EU regulations, these units are not approved for mobile use. The generators are sold as B-grade goods. B-grade means that the units may have cosmetic defects such as surface rust or rust on the housing. However, these defects do not affect the functionality or performance of the generators in any way. By accepting this offer, you expressly acknowledge the described properties of the units and their associated condition.

Condition: used, pressure 100 t Lajdpfxjvu E Uwo Aansk stroke 400 mm daylight longitudinal/sideways 1010 x 300 mm Motor output 4,0 kW liter capacity 11,0 l dayligth 900 mm table surface area 1010 x 560 mm feed down 4,8 mm/sec feed up 7,5 mm/sec weight of the machine ca. 0,9 t dimensions 1550 x 900 x 2450 mm High-quality hydraulic press can be operated manually or by motor. Cylinders can be moved sideways. Safety valve at cylinder end position. CE marked

Condition: new, maximum load weight: 44,000 kg, overall weight: 61,000 kg, axle configuration: 3 axles, Year of construction: 2025, Further information here: Lajdpov D Abtefx Aanok