IPCA IPN-ADR.FFDXXXXXIRQ board

HOMAG

Condition: used, Year of construction: 2007, power: 43 kW (58.46 HP), cutting height (max.): 90 mm, cutting width (max.): 1,200 mm, cutting length (max.): 5,600 mm, feed rate X-axis: 40 m/min, The machine comes from a business liquidation. Inspection under power is possible! TECHNICAL DETAILS Maximum panel width: 1,200 mm Maximum panel length: 5,600 mm Minimum panel width: 150 mm Minimum panel length: 250 mm Minimum panel height: 8 mm Maximum panel height: 90 mm Maximum feed speed: 40 m/min The machine is configured as follows: Number of processing units: 4 Unit 1: Double cutter, top and bottom Motor power: 11 kW Speed: 7,090 rpm Unit 2: Scoring unit Motor power: 2.2 kW Speed: 6,920 rpm Unit 3: Milling unit Motor power: 8 kW Gbedpfx Aoy R S I Uef Asl Speed: 7,090 rpm Unit 4: Milling unit Design type: on rear table Motor power: 2.2 kW Speed: 6,920 rpm MACHINE DETAILS Control system: WINDOWS Machine programming software: POWER CONTROL PC22 Total connected load: 43 kW EQUIPMENT Top pressure unit Additional guide for workpieces Rubber conveyor belt NC positioning system The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. External reference: 8448

Condition: used, Year of construction: 2007, travel distance X-axis: 6,000 mm, travel distance Y-axis: 3,000 mm, number of slots in tool magazine: 10, controller model: POWER CONTROL PC85, spindle speed (max.): 24,000 rpm, The machine originates from a business closure. Inspections under power are possible! TECHNICAL DETAILS Travel range X-axis: 6,000 mm Travel range Y-axis: 3,000 mm Working area X-axis: 5,600 mm Working area Y-axis: 1,200 mm Rapid traverse X-axis: 80 m/min Rapid traverse Y-axis: 80 m/min Rapid traverse Z-axis: 30 m/min Milling spindles: 2 Main electrospindle power: 11 kW Spindle speed: 24,000 rpm Total number of tool changer positions: 10 MACHINE DETAILS Type of operation: Milling Control system: POWER CONTROL PC85 Machine programming software: WOODWOP 5.0 Number of controlled axes: 4 Vacuum cups: 32 Individual vacuum pump capacity: 120 + 80 m³/h Number of pumps: 2 Total installed power: 27 kW EQUIPMENT Gbedpfxsy R Swij Af Asl Vacuum loading Motorized transfer system Automatic panel loading system Automatic panel stacking system Liquid cooling system CE marking Protective structure for operating units with safety sensors Protective netting on the machine Chip conveyor for waste removal The machine is being sold and delivered in its actual and legal condition ("as seen and approved") based on the photographic documentation and technical/commercial documents of descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 8457

Condition: used, Year of construction: 2002, travel distance X-axis: 10,500 mm, travel distance Y-axis: 2,700 mm, number of slots in tool magazine: 24, controller model: POWER CONTROL PC83, milling spindle speed (max.): 18,000 rpm, The machine comes from a business closure. Inspection under power is possible! TECHNICAL DETAILS Travel path X-axis: 10,500 mm Travel path Y-axis: 2,700 mm Working area X-axis: 5,600 mm Working area Y-axis: 1,200 mm Speed X-axis: 80 m/min Speed Y-axis: 80 m/min Speed Z-axis: 30 m/min Main electrospindle power: 12 kW Number of milling spindles: 2 Spindle motor output: 12 kW Spindle speed: 18,000 rpm Gbedpfx Ajy R Si Ssf Asl Number of controlled axes: 4 Number of tools in the changer: 24 Number of tool magazine positions: 12 (2 magazines) Maximum panel thickness: 40 mm Minimum panel thickness: 10 mm MACHINE DETAILS Type of machining: Edge processing, Milling Control system: POWER CONTROL PC83 Programming software: WOODWOP 5.0 Total installed power: 51 kW Number of work zones: 1 Number of rails: 5 Number of vacuum cups: 10 Number of vacuum pumps: 2 Capacity per pump: 120 m³/h EQUIPMENT Worktable: Pod and rail Positioning via NC Automatic panel loading system: vacuum loading system Automatic panel stacking system Vacuum pump Liquid cooling system Gluing unit with hot melt pre-melter Edgeband magazine Tool magazine at rear of machine Protective structure for operating units with safety sensors Protective net attached to the machine Safety system: front safety mats Waste chip conveyor The machine is sold and delivered in its current technical and legal condition ("as seen and approved"), based on photographic documentation and technical/commercial documents of descriptive character. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operating the machine at the destination. External reference: 8458

Condition: used, Year of construction: 2007, workpiece height (max.): 60 mm, edge thickness (max.): 35 mm, feed rate X-axis: 40 m/min, controller model: POWER CONTROL PC22", The machine comes from a company closure. Inspections under power are possible! TECHNICAL DETAILS Number of working units: 11 Maximum feed speed: 40 m/min Maximum panel thickness: 60 mm Minimum panel height: 16 mm Minimum panel width: 85 mm Minimum edge thickness: 0.3 mm Maximum edge thickness: 35 mm Pressure system: Rubber belt Workpiece support guides NC-controlled positioning Panel infeed alignment system The machine is configured as follows: PRE-MILLING / MILLING UNITS Number of pre-milling / milling units: 2 Unit 1: Pre-milling unit Motor power: 4.5 kW Speed: 5,860 rpm Automatic, time-controlled engagement Unit 2: End trimming unit Motor power: 1.8 kW Automatic tool change GLUING AND EDGE FEEDING Number of edge rollers: 68 Number of pressure rollers: 14 (1 x 7 + 1 x 7) Lamps for pre-heating the panel edge Pre-melter for PUR adhesive Gluing system Adhesive pot for PUR glue NC-controlled positioning EDGE PROCESSING UNITS Number of edge processing units: 8 Unit 1: End trimming unit Number of motors: 2 Motor power: 0.22 kW Speed: 10,350 rpm NC-controlled positioning Unit 2: Top and bottom flush trimming unit Number of motors: 2 Motor power: 0.55 kW Speed: 11,400 rpm Unit 3: Corner rounding unit Number of motors: 2 Motor power: 0.4 kW Speed: 10,980 rpm Automatic tool change NC-controlled positioning Automatic, time-controlled engagement Unit 4: Scraper unit NC-controlled positioning Unit 5: Glue joint scraper unit Unit 6: Buffing unit Number of motors: 4 Motor power: 0.25 kW Speed: 1,390 rpm Automatic, time-controlled engagement Unit 7: Buffing unit Number of motors: 1 Motor power: 0.30 kW Speed: 3,000 rpm Gjdpfxjy R R T Nj Af Aobl Unit 8: Buffing unit Number of motors: 2 Motor power: 0.18 kW Speed: 1,370 rpm MACHINE DETAILS Control system: WINDOWS XP Machine programming software: POWER CONTROL PC22 The machine is sold and delivered in its actual and legal condition (“as seen and agreed”) based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and is responsible for the installation, securing, and use of the machine at the destination. External reference: 8453

Condition: ready for operation (used), Year of construction: 2008, machine/vehicle number: 0-250-23-0021, functionality: fully functional, workpiece length (max.): 2,500 mm, workpiece width (max.): 1,000 mm, workpiece height (max.): 80 mm, feed rate X-axis: 138 m/min, feed rate Y-axis: 80 m/min, Submission of a bid obligates timely collection by 15.06.2026! TECHNICAL DETAILS X-axis speed: 138 m/min Y-axis speed: 80 m/min Z-axis speed: 50 m/min Workpiece length: 300–2,500 mm Gbjdey Sad Hopfx Af Ajl Workpiece width: 100–1,000 mm Workpiece height: 4–80 mm MACHINE DETAILS Control system: power control PC 85 T Dimensions (L x W x H): 6,500 × 2,300 × 2,700 mm Electrics: 3 × 415 V / 50 Hz Power consumption: 19.5 kW Fuse: 50 A Pneumatics: min. 7 bar Air consumption: 2,500 NL/min Extraction connection: 2 × 280 mm Extraction capacity: min. 4,450 m³/h

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, Used 5-axis CNC machining center Manufacturer: Homag Model: Centateq 110 (5-axis) Year of manufacture: 2021 Last manufacturer service: 18.05.2026 Console table with LED indicator for suction cup positioning, 6 manually adjustable consoles (length 1360 mm) each with 3 vacuum cups, 4 support rails Workpiece clamping via vacuum pump 63 m³/h LED system for vacuum clamping units, Working area X 3100 mm Working area Y up to 1250 mm (front stop); up to 1405 mm at the rear with 25 mm tool diameter Working area Z 260 mm / 160 mm with standard suction cups Drilling head with 12 vertical spindles; 6 (4+2) horizontal drilling spindles, Grooving saw, 90° swiveling, max. 125 mm diameter Main spindle DRIVE Future 10 kW, liquid-cooled, 1500 – 24,000 rpm 14-position tool changer (carousel) at the rear and 10-position linear tool changer fixed at the side Aggregate carrier for 2 Z-axes (main spindle + drilling gear unit) Chip conveyor, program-controlled dust extraction hood Power-Control PC 86 POWERTOUCH with Woodwop (incl. Lamello CLAMEX-P component), Gsdpfey Nzc Sox Af Aebl WoodWop also available for office station (Office Professional version; DXF-Import Basic) UPS for the PC; Tapio Ready-compatible Basic barcode reading system Documentation: German The tools shown, HSK tool holders, drills, etc. are not included in the scope of delivery! Machine available from end of May 2026 The attached PDF file for the machine description refers to the original delivery condition of the machine as delivered by the manufacturer in 2021 and is not binding for the current delivery condition as a used machine.

Condition: used, machine/vehicle number: 008522, Position 1: Robot HOMAG + KUKA-KFL10 + KR Gedpsy Nx U Eefx Af Asbl Position 2: Single Edgebanders HOMAG + KUKA-KFL10 + KR Position 3: Robot HOMAG + KUKA-KFL10 + KR Position 4: Panel Return Systems HOMAG + KUKA-KFL10 + KR

Condition: used, machine/vehicle number: 008323, Type of edging: Thin edge, Thick edge, Solid wood Gluing System: EVA Hotmelt, PUR Premilling Unit: yes Gbedpfox Hpkxsx Af Ajl Corner Rounding Unit: yes Max feed speed: 20 m/min Maximum panel thickness: 60 mm Operating Units: 7 nr

Condition: used, machine/vehicle number: 008526, X axis working area: 4000 mm Y axis working area: 1100 mm Working Table: Pod and Rail Main Electrospindle power: 12 KW Gedpfx Afoy Nx Ule Aobl Number of controlled axes: 5 axes Total number of drilling spindles: 35 Total number of tool changer positions: 29

Condition: used, machine/vehicle number: 008324, Max. panel width: 1000 mm Max. panel length: 2500 mm Length of conveyor: 7000 mm Panel return for edgebander: Right Gjdpfx Asx Hpkrof Asbl